3 - The "learn" action supports a new flag "delete_learned" that causes
4 the learned flows to be deleted when the flow with the "learn" action
6 - Basic support for the Geneve tunneling protocol. It is not yet
7 possible to generate or match options. This is planned for a future
8 release. The protocol is documented at
9 http://tools.ietf.org/html/draft-gross-geneve-00
14 - OpenFlow 1.1, 1.2, and 1.3 are now enabled by default in
16 - Linux kernel datapath now has an exact match cache optimizing the
17 flow matching process.
18 - Datapath flows now have partially wildcarded tranport port field
19 matches. This reduces userspace upcalls, but increases the
20 number of different masks in the datapath. The kernel datapath
21 exact match cache removes the overhead of matching the incoming
22 packets with the larger number of masks, but when paired with an
23 older kernel module, some workloads may perform worse with the
26 v2.2.0 - Internal Release
28 - Internal ports are no longer brought up by default, because it
29 should be an administrator task to bring up devices as they are
31 - ovs-vsctl now reports when ovs-vswitchd fails to create a new port or
33 - Port creation and configuration errors are now stored in a new error
34 column of the Interface table and included in 'ovs-vsctl show'.
35 - The "ovsdbmonitor" graphical tool has been removed, because it was
36 poorly maintained and not widely used.
37 - New "check-ryu" Makefile target for running Ryu tests for OpenFlow
38 controllers against Open vSwitch. See INSTALL for details.
39 - Added IPFIX support for SCTP flows and templates for ICMPv4/v6 flows.
40 - Upon the receipt of a SIGHUP signal, ovs-vswitchd no longer reopens its
41 log file (it will terminate instead). Please use 'ovs-appctl vlog/reopen'
43 - Support for Linux kernels up to 3.14. From Kernel 3.12 onwards OVS uses
44 tunnel API for GRE and VXLAN.
46 - Added support for custom vlog patterns in Python
51 - Address prefix tracking support for flow tables. New columns
52 "prefixes" in OVS-DB table "Flow_Table" controls which packet
53 header fields are used for address prefix tracking. Prefix
54 tracking allows the classifier to skip rules with longer than
55 necessary prefixes, resulting in better wildcarding for datapath
56 flows. Default configuration is to not use any fields for prefix
57 tracking. However, if any flow tables contain both exact matches
58 and masked matches for IP address fields, OVS performance may be
59 increased by using this feature.
60 * As of now, the fields for which prefix lookup can be enabled
61 are: 'tun_id', 'tun_src', 'tun_dst', 'nw_src', 'nw_dst' (or
62 aliases 'ip_src' and 'ip_dst'), 'ipv6_src', and 'ipv6_dst'.
63 (Using this feature for 'tun_id' would only make sense if the
64 tunnel IDs have prefix structure similar to IP addresses.)
65 * There is a maximum number of fields that can be enabled for any
66 one flow table. Currently this limit is 3.
68 $ ovs-vsctl set Bridge br0 flow_tables:0=@N1 -- \
69 --id=@N1 create Flow_Table name=table0
70 $ ovs-vsctl set Bridge br0 flow_tables:1=@N1 -- \
71 --id=@N1 create Flow_Table name=table1
72 $ ovs-vsctl set Flow_Table table0 prefixes=ip_dst,ip_src
73 $ ovs-vsctl set Flow_Table table1 prefixes=[]
74 - TCP flags matching: OVS now supports matching of TCP flags. This
75 has an adverse performance impact when using OVS userspace 1.10
76 or older (no megaflows support) together with the new OVS kernel
77 module. It is recommended that the kernel and userspace modules
78 both are upgraded at the same time.
79 - The default OpenFlow and OVSDB ports will change to
80 IANA-assigned numbers in a future release. Consider updating
81 your installations to specify port numbers instead of using the
84 * The OpenFlow 1.1+ "Write-Actions" instruction is now supported.
85 * OVS limits the OpenFlow port numbers it assigns to port 32767 and
86 below, leaving port numbers above that range free for assignment
88 * ovs-vswitchd now honors changes to the "ofport_request" column
89 in the Interface table by changing the port's OpenFlow port
91 - ovs-vswitchd.conf.db.5 man page will contain graphviz/dot
92 diagram only if graphviz package was installed at the build time.
93 - Support for Linux kernels up to 3.11
95 The "show" command also displays mega flow mask stats.
97 * New command "ofp-parse-pcap" to dump OpenFlow from PCAP files.
98 - ovs-controller has been renamed test-controller. It is no longer
99 packaged or installed by default, because too many users assumed
100 incorrectly that ovs-controller was a necessary or desirable part
101 of an Open vSwitch deployment.
102 - Added vlog option to export to a UDP syslog sink.
104 * The "monitor" command can now monitor all tables in a database,
105 instead of being limited to a single table.
106 - The flow-eviction-threshold has been replaced by the flow-limit which is a
107 hard limit on the number of flows in the datapath. It defaults to 200,000
108 flows. OVS automatically adjusts this number depending on network
110 - Added IPv6 support for active and passive socket communications.
114 ---------------------
115 - The ovs-vswitchd process is no longer single-threaded. Multiple
116 threads are now used to handle flow set up and asynchronous
119 * Experimental support for OpenFlow 1.1 (in addition to 1.2 and
120 1.3, which had experimental support in 1.10).
121 * Experimental protocol support for OpenFlow 1.1+ groups. This
122 does not yet include an implementation in the Open vSwitch
124 * Experimental protocol support for OpenFlow 1.2+ meters. This
125 does not yet include an implementation in the Open vSwitch
127 * New support for matching outer source and destination IP address
128 of tunneled packets, for tunnel ports configured with the newly
129 added "remote_ip=flow" and "local_ip=flow" options.
130 * Support for matching on metadata 'pkt_mark' for interacting with
131 other system components. On Linux this corresponds to the skb
133 * Support matching, rewriting SCTP ports
134 - The Interface table in the database has a new "ifindex" column to
135 report the interface's OS-assigned ifindex.
136 - New "check-oftest" Makefile target for running OFTest against Open
137 vSwitch. See README-OFTest for details.
138 - The flow eviction threshold has been moved to the Open_vSwitch table.
139 - Database names are now mandatory when specifying ovsdb-server options
140 through database paths (e.g. Private key option with the database name
141 should look like "--private-key=db:Open_vSwitch,SSL,private_key").
142 - Added ovs-dev.py, a utility script helpful for Open vSwitch developers.
143 - Support for Linux kernels up to 3.10
145 * New "ofp-parse" for printing OpenFlow messages read from a file.
146 * New commands for OpenFlow 1.1+ groups.
147 - Added configurable flow caching support to IPFIX exporter.
148 - Dropped support for Linux pre-2.6.32.
149 - Log file timestamps and ovsdb commit timestamps are now reported
150 with millisecond resolution. (Previous versions only reported
154 v1.11.0 - 28 Aug 2013
155 ---------------------
156 - Support for megaflows, which allows wildcarding in the kernel (and
157 any dpif implementation that supports wildcards). Depending on
158 the flow table and switch configuration, flow set up rates are
159 close to the Linux bridge.
160 - The "tutorial" directory contains a new tutorial for some advanced
161 Open vSwitch features.
162 - Stable bond mode has been removed.
163 - The autopath action has been removed.
164 - New support for the data encapsulation format of the LISP tunnel
165 protocol (RFC 6830). An external control plane or manual flow
166 setup is required for EID-to-RLOC mapping.
168 * The "dec_mpls_ttl" and "set_mpls_ttl" actions from OpenFlow
169 1.1 and later are now implemented.
170 * New "stack" extension for use in actions, to push and pop from
172 * The "load" and "set_field" actions can now modify the "in_port". (This
173 allows one to enable output to a flow's input port by setting the
174 in_port to some unused value, such as OFPP_NONE.)
176 * New debugging commands "add-flow", "mod-flow", "del-flow".
177 * "dump-flows" now has a -m option to increase output verbosity.
178 - In dpif-based bridges, cache action translations, which can improve
179 flow set up performance by 80% with a complicated flow table.
180 - New syslog format, prefixed with "ovs|", to be easier to filter.
181 - RHEL: Removes the default firewall rule that allowed GRE traffic to
182 pass through. Any users that relied on this automatic firewall hole
183 will have to manually configure it. The ovs-ctl(8) manpage documents
184 the "enable-protocol" command that can be used as an alternative.
185 - New CFM demand mode which uses data traffic to indicate interface
188 v1.10.0 - 01 May 2013
189 ---------------------
190 - Bridge compatibility support has been removed. Any uses that
191 rely on ovs-brcompatd will have to stick with Open vSwitch 1.9.x
192 or adapt to native Open vSwitch support (e.g. use ovs-vsctl instead
194 - The maximum size of the MAC learning table is now configurable.
195 - With the Linux datapath, packets for new flows are now queued
196 separately on a per-port basis, so it should no longer be
197 possible for a large number of new flows arriving on one port to
198 prevent new flows from being processed on other ports.
200 * Previously ovs-vsctl would retry connecting to the database forever,
201 causing it to hang if ovsdb-server was not running. Now, ovs-vsctl
202 only tries once by default (use --retry to try forever). This change
203 means that you may want to remove uses of --timeout to avoid hangs
205 * Many "ovs-vsctl" database commands now accept an --if-exists option.
206 Please refer to the ovs-vsctl manpage for details.
208 - Experimental support for newer versions of OpenFlow. See
209 the "What versions of OpenFlow does Open vSwitch support?"
210 question in the FAQ for more details.
211 - The OpenFlow "dp_desc" may now be configured by setting the
212 value of other-config:dp-desc in the Bridge table.
213 - It is possible to request the OpenFlow port number with the
214 "ofport_request" column in the Interface table.
215 - The NXM flow_removed message now reports the OpenFlow table ID
216 from which the flow was removed.
218 - New support for the VXLAN tunnel protocol (see the IETF draft here:
219 http://tools.ietf.org/html/draft-mahalingam-dutt-dcops-vxlan-03).
220 - Tunneling requires the version of the kernel module paired with
221 Open vSwitch 1.9.0 or later.
222 - Inheritance of the Don't Fragment bit in IP tunnels (df_inherit)
223 is no longer supported.
224 - Path MTU discovery is no longer supported.
225 - CAPWAP tunneling support removed.
226 - Tunnels with multicast destination ports are no longer supported.
228 - The "dump-flows" and "del-flows" no longer require an argument
229 if only one datapath exists.
231 - New "vlog/disable-rate-limit" and "vlog/enable-rate-limit"
232 commands available allow control over logging rate limits.
233 - New "dpif/dump-dps", "dpif/show", and "dpif/dump-flows" command
234 that mimic the equivalent ovs-dpctl commands.
235 - The ofproto library is now responsible for assigning OpenFlow port
236 numbers. An ofproto implementation should assign them when
237 port_construct() is called.
238 - All dpif-based bridges of a particular type share a common
239 datapath called "ovs-<type>", e.g. "ovs-system". The ovs-dpctl
240 commands will now return information on that shared datapath. To
241 get the equivalent bridge-specific information, use the new
242 "ovs-appctl dpif/*" commands.
243 - Backward-incompatible changes:
244 - Earlier Open vSwitch versions treated ANY as a wildcard in flow
245 syntax. OpenFlow 1.1 adds a port named ANY, which introduces a
246 conflict. ANY was rarely used in flow syntax, so we chose to
247 retire that meaning of ANY in favor of the OpenFlow 1.1 meaning.
248 - Patch ports no longer require kernel support, so they now work
249 with FreeBSD and the kernel module built into Linux 3.3 and later.
250 - New "sample" action.
254 ------------------------
256 - Support for ipv6 set action.
257 - SKB mark matching and setting.
258 - support for Linux kernels up to 3.8
259 - FreeBSD is now a supported platform, thanks to code contributions from
260 Gaetano Catalli, Ed Maste, and Giuseppe Lettieri.
261 - ovs-bugtool: New --ovs option to report only OVS related information.
262 - New %t and %T log escapes to identify the subprogram within a
263 cooperating group of processes or threads that emitted a log message.
264 The default log patterns now include this information.
266 - Allow bitwise masking for SHA and THA fields in ARP, SLL and TLL
267 fields in IPv6 neighbor discovery messages, and IPv6 flow label.
268 - Adds support for writing to the metadata field for a flow.
270 - The tunneling code no longer assumes input and output keys are
271 symmetric. If they are not, PMTUD needs to be disabled for
272 tunneling to work. Note this only applies to flow-based keys.
273 - New support for a nonstandard form of GRE that supports a 64-bit key.
274 - Tunnel Path MTU Discovery default value was set to 'disabled'.
275 This feature is deprecated and will be removed soon.
276 - Tunnel header caching removed.
278 - Commands and actions that accept port numbers now also accept keywords
279 that represent those ports (such as LOCAL, NONE, and ALL). This is
280 also the recommended way to specify these ports, for compatibility
281 with OpenFlow 1.1 and later (which use the OpenFlow 1.0 numbers
282 for these ports for different purposes).
284 - Support requesting the port number with the "port_no" option in
285 the "add-if" command.
286 - ovs-pki: The "online PKI" features have been removed, along with
287 the ovs-pki-cgi program that facilitated it, because of some
288 alarmist insecurity claims. We do not believe that these claims
289 are true, but because we do not know of any users for this
290 feature it seems better on balance to remove it. (The ovs-pki-cgi
291 program was not included in distribution packaging.)
292 - ovsdb-server now enforces the immutability of immutable columns. This
293 was not enforced in earlier versions due to an oversight.
294 - The following features are now deprecated. They will be removed no
295 earlier than February 2013. Please email dev@openvswitch.org with
297 - Bridge compatibility.
299 - The autopath action.
300 - Interface type "null".
301 - Numeric values for reserved ports (see "ovs-ofctl" note above).
302 - Tunnel Path MTU Discovery.
303 - CAPWAP tunnel support.
304 - The data in the RARP packets can now be matched in the same way as the
309 ------------------------
310 *** Internal only release ***
311 - New FAQ. Please send updates and additions!
312 - Authors of controllers, please read the new section titled "Action
313 Reproduction" in DESIGN, which describes an Open vSwitch change in
314 behavior in corner cases that may affect some controllers.
316 - A new test utility that can create L3 tunnel between two Open
317 vSwitches and detect connectivity issues.
319 - New --sort and --rsort options for "dump-flows" command.
320 - "mod-port" command can now control all OpenFlow config flags.
322 - Allow general bitwise masking for IPv4 and IPv6 addresses in
323 IPv4, IPv6, and ARP packets. (Previously, only CIDR masks
325 - Allow support for arbitrary Ethernet masks. (Previously, only
326 the multicast bit in the destination address could be individually
328 - New field OXM_OF_METADATA, to align with OpenFlow 1.1.
329 - The OFPST_QUEUE request now reports an error if a specified port or
330 queue does not exist, or for requests for a specific queue on all
331 ports, if the specified queue does not exist on any port. (Previous
332 versions generally reported an empty set of results.)
333 - New "flow monitor" feature to allow controllers to be notified of
334 flow table changes as they happen.
335 - Additional protocols are not mirrored and dropped when forward-bpdu is
336 false. For a full list, see the ovs-vswitchd.conf.db man page.
337 - Open vSwitch now sends RARP packets in situations where it previously
338 sent a custom protocol, making it consistent with behavior of QEMU and
340 - All Open vSwitch programs and log files now show timestamps in UTC,
341 instead the local timezone, by default.
345 ------------------------
346 - kernel modules are renamed. openvswitch_mod.ko is now
347 openvswitch.ko and brcompat_mod.ko is now brcompat.ko.
348 - Increased the number of NXM registers to 8.
349 - Added ability to configure DSCP setting for manager and controller
350 connections. By default, these connections have a DSCP value of
351 Internetwork Control (0xc0).
352 - Added the granular link health statistics, 'cfm_health', to an
355 - Added support to mask nd_target for ICMPv6 neighbor discovery flows.
356 - Added support for OpenFlow 1.3 port description (OFPMP_PORT_DESC)
359 - Added the "dump-ports-desc" command to retrieve port
360 information using the new port description multipart messages.
362 - Added support for spawning ovs-test server from the client.
363 - Now ovs-test is able to automatically create test bridges and ports.
364 - "ovs-dpctl dump-flows" now prints observed TCP flags in TCP flows.
365 - Tripled flow setup performance.
366 - The "coverage/log" command previously available through ovs-appctl
367 has been replaced by "coverage/show". The new command replies with
368 coverage counter values, instead of logging them.
372 ------------------------
373 - Allow OFPP_CONTROLLER as the in_port for packet-out messages.
377 ------------------------
378 *** Internal only release ***
380 - LACP bonds no longer fall back to balance-slb when negotiations fail.
381 Instead they drop traffic.
382 - The default bond_mode changed from SLB to active-backup, to protect
383 unsuspecting users from the significant risks of SLB bonds (which are
384 documented in vswitchd/INTERNALS).
385 - Load balancing can be disabled by setting the bond-rebalance-interval
388 - Added support for bitwise matching on TCP and UDP ports.
389 See ovs-ofctl(8) for more information.
390 - NXM flow dumps now include times elapsed toward idle and hard
392 - Added an OpenFlow extension NXT_SET_ASYNC_CONFIG that allows
393 controllers more precise control over which OpenFlow messages they
394 receive asynchronously.
395 - New "fin_timeout" action.
396 - Added "fin_timeout" support to "learn" action.
397 - New Nicira action NXAST_CONTROLLER that offers additional features
398 over output to OFPP_CONTROLLER.
399 - When QoS settings for an interface do not configure a default queue
400 (queue 0), Open vSwitch now uses a default configuration for that
401 queue, instead of dropping all packets as in previous versions.
403 - Logging to console and file will have UTC timestamp as a default for
404 all the daemons. An example of the default format is
405 2012-01-27T16:35:17Z. ovs-appctl can be used to change the default
407 - The syntax of commands and options to set log levels was simplified,
408 to make it easier to remember.
409 - New support for limiting the number of flows in an OpenFlow flow
410 table, with configurable policy for evicting flows upon
411 overflow. See the Flow_Table table in ovs-vswitch.conf.db(5)
412 for more information.
413 - New "enable-async-messages" column in the Controller table. If set to
414 false, OpenFlow connections to the controller will initially have all
415 asynchronous messages disabled, overriding normal OpenFlow behavior.
416 - ofproto-provider interface:
417 - "struct rule" has a new member "used" that ofproto implementations
418 should maintain by updating with ofproto_rule_update_used().
420 - The new option --timestamp causes the "monitor" command to print
421 a timestamp with every update.
422 - CFM module CCM broadcasts can now be tagged with an 802.1p priority.
426 ------------------------
428 - Added support for querying, modifying, and deleting flows
429 based on flow cookie when using NXM.
430 - Added new NXM_PACKET_IN format.
431 - Added new NXAST_DEC_TTL action.
433 - Added daemonization support to the monitor and snoop commands.
435 - The "find" command supports new set relational operators
436 {=}, {!=}, {<}, {>}, {<=}, and {>=}.
437 - ovsdb-tool now uses the typical database and schema installation
438 directories as defaults.
439 - The default MAC learning timeout has been increased from 60 seconds
440 to 300 seconds. The MAC learning timeout is now configurable.
444 ------------------------
445 - Compatible with Open vSwitch kernel module included in Linux 3.3.
446 - New "VLAN splinters" feature to work around buggy device drivers
447 in old Linux versions. (This feature is deprecated. When
448 broken device drivers are no longer in widespread use, we will
449 delete this feature.) See ovs-vswitchd.conf.db(5) for more
452 - Added ability to match on IPv6 flow label through NXM.
453 - Added ability to match on ECN bits in IPv4 and IPv6 through NXM.
454 - Added ability to match on TTL in IPv4 and IPv6 through NXM.
455 - Added ability to modify ECN bits in IPv4.
456 - Added ability to modify TTL in IPv4.
458 - Don't require the "normal" action to use mirrors. Traffic will
459 now be properly mirrored for any flows, regardless of their
461 - Track packet and byte statistics sent on mirrors.
462 - The sFlow implementation can now usually infer the correct agent
463 device instead of having to be told explicitly.
465 - New "fdb/flush" command to flush bridge's MAC learning table.
467 - A new distributed testing tool that allows one to diagnose performance
468 and connectivity issues. This tool currently is not included in RH or
470 - RHEL packaging now supports integration with Red Hat network scripts.
472 - Post 1.4.*, OVS will be changing the default bond mode from balance-slb
473 to active-backup. SLB bonds carry significant risks with them
474 (documented vswitchd/INTERNALS) which we want to prevent unsuspecting
475 users from running into. Users are advised to update any scripts or
476 configuration which may be negatively impacted by explicitly setting
477 the bond mode which they want to use.
481 ------------------------
483 - Added an OpenFlow extension which allows the "output" action to accept
485 - Added an OpenFlow extension for flexible learning.
486 - Bumped number of NXM registers from four to five.
488 - New "version" command to determine version of running daemon.
489 - If no argument is provided for "cfm/show", displays detailed
490 information about all interfaces with CFM enabled.
491 - If no argument is provided for "lacp/show", displays detailed
492 information about all ports with LACP enabled.
494 - New "set-if" command to modify a datapath port's configuration.
496 - The software switch now supports 255 OpenFlow tables, instead
497 of just one. By default, only table 0 is consulted, but the
498 new NXAST_RESUBMIT_TABLE action can look up in additional
499 tables. Tables 128 and above are reserved for use by the
500 switch itself; please use only tables 0 through 127.
501 - Add support for 802.1D spanning tree (STP).
502 - Fragment handling extensions:
503 - New OFPC_FRAG_NX_MATCH fragment handling mode, in which L4
504 fields are made available for matching in fragments with
506 - New NXM_NX_IP_FRAG match field for matching IP fragments (usable
507 via "ip_frag" in ovs-ofctl).
508 - New ovs-ofctl "get-frags" and "set-frags" commands to get and set
509 fragment handling policy.
510 - CAPWAP tunneling now supports an extension to transport a 64-bit key.
511 By default it remains compatible with the old version and other
512 standards-based implementations.
513 - Flow setups are now processed in a round-robin manner across ports
514 to prevent any single client from monopolizing the CPU and conducting
515 a denial of service attack.
516 - Added support for native VLAN tagging. A new "vlan_mode"
517 parameter can be set for "port". Possible values: "access",
518 "trunk", "native-tagged" and "native-untagged".
519 - test-openflowd has been removed. Please use ovs-vswitchd instead.
522 ------------------------
523 - New "ofproto" abstraction layer to ease porting to hardware
525 - Packaging for Red Hat Enterprise Linux 5.6 and 6.0.
526 - Datapath support for Linux kernels up to 3.0.
528 - New "bundle" and "bundle_load" action extensions.
530 - Implement table unique constraints.
531 - Support cooperative locking between callers.
533 - New "-s" option for "show" command prints packet and byte
534 counters for each port.
536 - New "--readd" option for "replace-flows".
538 - New "show" command to print an overview of configuration.
539 - New "comment" command to add remark that explains intentions.
540 - ovs-brcompatd has been rewritten to fix long-standing bugs.
541 - ovs-openflowd has been renamed test-openflowd and moved into the
542 tests directory. Its presence confused too many users. Please
543 use ovs-vswitchd instead.
544 - New ovs-benchmark utility to test flow setup performance.
545 - A new log level "off" has been added. Configuring a log facility
546 "off" prevents any messages from being logged to it. Previously,
547 "emer" was effectively "off" because no messages were ever logged at
548 level "emer". Now, errors that cause a process to exit are logged
550 - "configure" option --with-l26 has been renamed --with-linux, and
551 --with-l26-source has been renamed --with-linux-source. The old
552 names will be removed after the next release, so please update
554 - The "-2.6" suffix has been dropped from the datapath/linux-2.6 and
555 datapath/linux-2.6/compat-2.6 directories.
557 - Dropped support for "tun_id_from_cookie" OpenFlow extension.
558 Please use the extensible match extensions instead.
559 - Removed the Maintenance_Point and Monitor tables in an effort
560 to simplify 802.1ag configuration.
561 - Performance and scalability improvements
565 ------------------------
566 - Ability to define policies over IPv6
569 - Support for extensible match extensions to OpenFlow
571 - Support for HFSC qdisc.
572 - Queue used by in-band control can now be configured.
574 - Kernel<->userspace interface has been reworked and should be
575 close to a stable ABI now.
576 - "Port group" concept has been dropped.
577 - GRE over IPSEC tunnels
579 - New active backup bonding mode.
580 - New L4 hashing support when LACP is enabled.
581 - Source MAC hash now includes VLAN field also.
583 - Greatly improved handling of large flow tables
585 - "show" command now prints full vport configuration.
586 - "dump-groups" command removed since kernel support for
587 port groups was dropped.
589 - New commands for working with the new Managers table.
590 - "list" command enhanced with new formatting options and --columns
592 - "get" command now accepts new --id option.
593 - New "find" command.
595 - New "queue-stats" command for printing queue stats.
596 - New commands "replace-flows" and "diff-flows".
597 - Commands to add and remove flows can now read from files.
598 - New --flow-format option to enable or disable NXM.
599 - New --more option to increase OpenFlow message verbosity.
600 - Removed "tun-cookie" command, which is no longer useful.
601 - ovs-controller enhancements for testing various features.
602 - New ovs-vlan-test command for testing for Linux kernel driver VLAN
603 bugs. New ovs-vlan-bug-workaround command for enabling and
604 disabling a workaround for these driver bugs.
606 - "Resubmit" actions now update flow statistics.
607 - New "register" extension for use in matching and actions, via NXM.
608 - New "multipath" experimental action extension.
609 - New support for matching multicast Ethernet frames, via NXM.
610 - New extension for OpenFlow vendor error codes.
611 - New extension to set the QoS output queue without actually
612 sending to an output port.
613 - Open vSwitch now reports a single flow table, instead of
614 separate hash and wildcard tables. This better models the
615 current implementation.
616 - New experimental "note" action.
617 - New "ofproto/trace" ovs-appctl command and associated utilities
618 to ease debugging complex flow tables.
620 - Schema documentation now includes an entity-relationship diagram.
621 - The database is now garbage collected. In most tables,
622 unreferenced rows will be deleted automatically.
623 - Many tables now include statistics updated periodically by
624 ovs-vswitchd or ovsdb-server.
625 - Every table now has an "external-ids" column for use by OVS
627 - There is no default controller anymore. Each bridge must have its
628 controller individually specified.
629 - The "fail-mode" is now a property of a Bridge instead of a Controller.
630 - New versioning and checksum features.
631 - New Managers table and manager_options column in Open_vSwitch table
632 for specifying managers. The old "managers" column in the
633 Open_vSwitch table has been removed.
634 - Many "name" columns are now immutable.
636 - Dropped support for XenServer pre-5.6.100.
637 - Dropped support for Linux pre-2.6.18.
638 - Dropped controller discovery support.
639 - Dropped "ovs-ofctl status" and the OpenFlow extension that it used.
640 Statistics reporting in the database is a rough equivalent.
641 - Dropped the "corekeeper" package (now separate, at
642 http://openvswitch.org/cgi-bin/gitweb.cgi?p=corekeeper).
643 - Performance and scalability improvements
646 v1.1.0pre2 - 13 Sep 2010
647 ------------------------
650 v1.1.0pre1 - 31 Aug 2010
651 ------------------------
652 - OpenFlow 1.0 slicing (QoS) functionality
653 - Python bindings for configuration database (no write support)
654 - Performance and scalability improvements
659 - New "patch" interface type
664 - Configuration database with remote management
667 - Support for XenServer 5.5 and 5.6
668 - Performance and scalability improvements
671 v0.99.2 - 18 Feb 2010
672 ---------------------
675 v0.99.1 - 25 Jan 2010
676 ---------------------
677 - Add support for sFlow(R)
678 - Make headers compatible with C++
681 v0.99.0 - 14 Jan 2010
682 ---------------------
683 - User-space forwarding engine
686 v0.90.7 - 29 Nov 2009
687 ---------------------
688 - Add support for NetFlow active timeouts
695 v0.90.5 - 21 Sep 2009
696 ---------------------
697 - Generalize in-band control to more diverse network setups