3 - The "learn" action supports a new flag "delete_learned" that causes
4 the learned flows to be deleted when the flow with the "learn" action
6 - Basic support for the Geneve tunneling protocol. It is not yet
7 possible to generate or match options. This is planned for a future
8 release. The protocol is documented at
9 http://tools.ietf.org/html/draft-gross-geneve-00
10 - The OVS database now reports controller rate limiting statistics.
11 - ovs-dpctl functionality is now available for datapaths integrated
12 into ovs-vswitchd, via ovs-appctl. Some existing ovs-appctl
13 commands are now redundant and will be removed in a future
14 release. See ovs-vswitchd(8) for details.
16 * OpenFlow 1.5 (draft) extended registers are now supported.
17 * OpenFlow 1.3+ table features requests are now supported (read-only).
22 - OpenFlow 1.1, 1.2, and 1.3 are now enabled by default in
24 - Linux kernel datapath now has an exact match cache optimizing the
25 flow matching process.
26 - Datapath flows now have partially wildcarded tranport port field
27 matches. This reduces userspace upcalls, but increases the
28 number of different masks in the datapath. The kernel datapath
29 exact match cache removes the overhead of matching the incoming
30 packets with the larger number of masks, but when paired with an
31 older kernel module, some workloads may perform worse with the
33 - Support for multicast snooping (IGMPv1 and IGMPv2)
34 - Compatibility with autoconf 2.63 (previously >=2.64)
36 v2.2.0 - Internal Release
38 - Internal ports are no longer brought up by default, because it
39 should be an administrator task to bring up devices as they are
41 - ovs-vsctl now reports when ovs-vswitchd fails to create a new port or
43 - Port creation and configuration errors are now stored in a new error
44 column of the Interface table and included in 'ovs-vsctl show'.
45 - The "ovsdbmonitor" graphical tool has been removed, because it was
46 poorly maintained and not widely used.
47 - New "check-ryu" Makefile target for running Ryu tests for OpenFlow
48 controllers against Open vSwitch. See INSTALL for details.
49 - Added IPFIX support for SCTP flows and templates for ICMPv4/v6 flows.
50 - Upon the receipt of a SIGHUP signal, ovs-vswitchd no longer reopens its
51 log file (it will terminate instead). Please use 'ovs-appctl vlog/reopen'
53 - Support for Linux kernels up to 3.14. From Kernel 3.12 onwards OVS uses
54 tunnel API for GRE and VXLAN.
56 - Added support for custom vlog patterns in Python
61 - Address prefix tracking support for flow tables. New columns
62 "prefixes" in OVS-DB table "Flow_Table" controls which packet
63 header fields are used for address prefix tracking. Prefix
64 tracking allows the classifier to skip rules with longer than
65 necessary prefixes, resulting in better wildcarding for datapath
66 flows. Default configuration is to not use any fields for prefix
67 tracking. However, if any flow tables contain both exact matches
68 and masked matches for IP address fields, OVS performance may be
69 increased by using this feature.
70 * As of now, the fields for which prefix lookup can be enabled
71 are: 'tun_id', 'tun_src', 'tun_dst', 'nw_src', 'nw_dst' (or
72 aliases 'ip_src' and 'ip_dst'), 'ipv6_src', and 'ipv6_dst'.
73 (Using this feature for 'tun_id' would only make sense if the
74 tunnel IDs have prefix structure similar to IP addresses.)
75 * There is a maximum number of fields that can be enabled for any
76 one flow table. Currently this limit is 3.
78 $ ovs-vsctl set Bridge br0 flow_tables:0=@N1 -- \
79 --id=@N1 create Flow_Table name=table0
80 $ ovs-vsctl set Bridge br0 flow_tables:1=@N1 -- \
81 --id=@N1 create Flow_Table name=table1
82 $ ovs-vsctl set Flow_Table table0 prefixes=ip_dst,ip_src
83 $ ovs-vsctl set Flow_Table table1 prefixes=[]
84 - TCP flags matching: OVS now supports matching of TCP flags. This
85 has an adverse performance impact when using OVS userspace 1.10
86 or older (no megaflows support) together with the new OVS kernel
87 module. It is recommended that the kernel and userspace modules
88 both are upgraded at the same time.
89 - The default OpenFlow and OVSDB ports will change to
90 IANA-assigned numbers in a future release. Consider updating
91 your installations to specify port numbers instead of using the
94 * The OpenFlow 1.1+ "Write-Actions" instruction is now supported.
95 * OVS limits the OpenFlow port numbers it assigns to port 32767 and
96 below, leaving port numbers above that range free for assignment
98 * ovs-vswitchd now honors changes to the "ofport_request" column
99 in the Interface table by changing the port's OpenFlow port
101 - ovs-vswitchd.conf.db.5 man page will contain graphviz/dot
102 diagram only if graphviz package was installed at the build time.
103 - Support for Linux kernels up to 3.11
105 The "show" command also displays mega flow mask stats.
107 * New command "ofp-parse-pcap" to dump OpenFlow from PCAP files.
108 - ovs-controller has been renamed test-controller. It is no longer
109 packaged or installed by default, because too many users assumed
110 incorrectly that ovs-controller was a necessary or desirable part
111 of an Open vSwitch deployment.
112 - Added vlog option to export to a UDP syslog sink.
114 * The "monitor" command can now monitor all tables in a database,
115 instead of being limited to a single table.
116 - The flow-eviction-threshold has been replaced by the flow-limit which is a
117 hard limit on the number of flows in the datapath. It defaults to 200,000
118 flows. OVS automatically adjusts this number depending on network
120 - Added IPv6 support for active and passive socket communications.
124 ---------------------
125 - The ovs-vswitchd process is no longer single-threaded. Multiple
126 threads are now used to handle flow set up and asynchronous
129 * Experimental support for OpenFlow 1.1 (in addition to 1.2 and
130 1.3, which had experimental support in 1.10).
131 * Experimental protocol support for OpenFlow 1.1+ groups. This
132 does not yet include an implementation in the Open vSwitch
134 * Experimental protocol support for OpenFlow 1.2+ meters. This
135 does not yet include an implementation in the Open vSwitch
137 * New support for matching outer source and destination IP address
138 of tunneled packets, for tunnel ports configured with the newly
139 added "remote_ip=flow" and "local_ip=flow" options.
140 * Support for matching on metadata 'pkt_mark' for interacting with
141 other system components. On Linux this corresponds to the skb
143 * Support matching, rewriting SCTP ports
144 - The Interface table in the database has a new "ifindex" column to
145 report the interface's OS-assigned ifindex.
146 - New "check-oftest" Makefile target for running OFTest against Open
147 vSwitch. See README-OFTest for details.
148 - The flow eviction threshold has been moved to the Open_vSwitch table.
149 - Database names are now mandatory when specifying ovsdb-server options
150 through database paths (e.g. Private key option with the database name
151 should look like "--private-key=db:Open_vSwitch,SSL,private_key").
152 - Added ovs-dev.py, a utility script helpful for Open vSwitch developers.
153 - Support for Linux kernels up to 3.10
155 * New "ofp-parse" for printing OpenFlow messages read from a file.
156 * New commands for OpenFlow 1.1+ groups.
157 - Added configurable flow caching support to IPFIX exporter.
158 - Dropped support for Linux pre-2.6.32.
159 - Log file timestamps and ovsdb commit timestamps are now reported
160 with millisecond resolution. (Previous versions only reported
164 v1.11.0 - 28 Aug 2013
165 ---------------------
166 - Support for megaflows, which allows wildcarding in the kernel (and
167 any dpif implementation that supports wildcards). Depending on
168 the flow table and switch configuration, flow set up rates are
169 close to the Linux bridge.
170 - The "tutorial" directory contains a new tutorial for some advanced
171 Open vSwitch features.
172 - Stable bond mode has been removed.
173 - The autopath action has been removed.
174 - New support for the data encapsulation format of the LISP tunnel
175 protocol (RFC 6830). An external control plane or manual flow
176 setup is required for EID-to-RLOC mapping.
178 * The "dec_mpls_ttl" and "set_mpls_ttl" actions from OpenFlow
179 1.1 and later are now implemented.
180 * New "stack" extension for use in actions, to push and pop from
182 * The "load" and "set_field" actions can now modify the "in_port". (This
183 allows one to enable output to a flow's input port by setting the
184 in_port to some unused value, such as OFPP_NONE.)
186 * New debugging commands "add-flow", "mod-flow", "del-flow".
187 * "dump-flows" now has a -m option to increase output verbosity.
188 - In dpif-based bridges, cache action translations, which can improve
189 flow set up performance by 80% with a complicated flow table.
190 - New syslog format, prefixed with "ovs|", to be easier to filter.
191 - RHEL: Removes the default firewall rule that allowed GRE traffic to
192 pass through. Any users that relied on this automatic firewall hole
193 will have to manually configure it. The ovs-ctl(8) manpage documents
194 the "enable-protocol" command that can be used as an alternative.
195 - New CFM demand mode which uses data traffic to indicate interface
198 v1.10.0 - 01 May 2013
199 ---------------------
200 - Bridge compatibility support has been removed. Any uses that
201 rely on ovs-brcompatd will have to stick with Open vSwitch 1.9.x
202 or adapt to native Open vSwitch support (e.g. use ovs-vsctl instead
204 - The maximum size of the MAC learning table is now configurable.
205 - With the Linux datapath, packets for new flows are now queued
206 separately on a per-port basis, so it should no longer be
207 possible for a large number of new flows arriving on one port to
208 prevent new flows from being processed on other ports.
210 * Previously ovs-vsctl would retry connecting to the database forever,
211 causing it to hang if ovsdb-server was not running. Now, ovs-vsctl
212 only tries once by default (use --retry to try forever). This change
213 means that you may want to remove uses of --timeout to avoid hangs
215 * Many "ovs-vsctl" database commands now accept an --if-exists option.
216 Please refer to the ovs-vsctl manpage for details.
218 - Experimental support for newer versions of OpenFlow. See
219 the "What versions of OpenFlow does Open vSwitch support?"
220 question in the FAQ for more details.
221 - The OpenFlow "dp_desc" may now be configured by setting the
222 value of other-config:dp-desc in the Bridge table.
223 - It is possible to request the OpenFlow port number with the
224 "ofport_request" column in the Interface table.
225 - The NXM flow_removed message now reports the OpenFlow table ID
226 from which the flow was removed.
228 - New support for the VXLAN tunnel protocol (see the IETF draft here:
229 http://tools.ietf.org/html/draft-mahalingam-dutt-dcops-vxlan-03).
230 - Tunneling requires the version of the kernel module paired with
231 Open vSwitch 1.9.0 or later.
232 - Inheritance of the Don't Fragment bit in IP tunnels (df_inherit)
233 is no longer supported.
234 - Path MTU discovery is no longer supported.
235 - CAPWAP tunneling support removed.
236 - Tunnels with multicast destination ports are no longer supported.
238 - The "dump-flows" and "del-flows" no longer require an argument
239 if only one datapath exists.
241 - New "vlog/disable-rate-limit" and "vlog/enable-rate-limit"
242 commands available allow control over logging rate limits.
243 - New "dpif/dump-dps", "dpif/show", and "dpif/dump-flows" command
244 that mimic the equivalent ovs-dpctl commands.
245 - The ofproto library is now responsible for assigning OpenFlow port
246 numbers. An ofproto implementation should assign them when
247 port_construct() is called.
248 - All dpif-based bridges of a particular type share a common
249 datapath called "ovs-<type>", e.g. "ovs-system". The ovs-dpctl
250 commands will now return information on that shared datapath. To
251 get the equivalent bridge-specific information, use the new
252 "ovs-appctl dpif/*" commands.
253 - Backward-incompatible changes:
254 - Earlier Open vSwitch versions treated ANY as a wildcard in flow
255 syntax. OpenFlow 1.1 adds a port named ANY, which introduces a
256 conflict. ANY was rarely used in flow syntax, so we chose to
257 retire that meaning of ANY in favor of the OpenFlow 1.1 meaning.
258 - Patch ports no longer require kernel support, so they now work
259 with FreeBSD and the kernel module built into Linux 3.3 and later.
260 - New "sample" action.
264 ------------------------
266 - Support for ipv6 set action.
267 - SKB mark matching and setting.
268 - support for Linux kernels up to 3.8
269 - FreeBSD is now a supported platform, thanks to code contributions from
270 Gaetano Catalli, Ed Maste, and Giuseppe Lettieri.
271 - ovs-bugtool: New --ovs option to report only OVS related information.
272 - New %t and %T log escapes to identify the subprogram within a
273 cooperating group of processes or threads that emitted a log message.
274 The default log patterns now include this information.
276 - Allow bitwise masking for SHA and THA fields in ARP, SLL and TLL
277 fields in IPv6 neighbor discovery messages, and IPv6 flow label.
278 - Adds support for writing to the metadata field for a flow.
280 - The tunneling code no longer assumes input and output keys are
281 symmetric. If they are not, PMTUD needs to be disabled for
282 tunneling to work. Note this only applies to flow-based keys.
283 - New support for a nonstandard form of GRE that supports a 64-bit key.
284 - Tunnel Path MTU Discovery default value was set to 'disabled'.
285 This feature is deprecated and will be removed soon.
286 - Tunnel header caching removed.
288 - Commands and actions that accept port numbers now also accept keywords
289 that represent those ports (such as LOCAL, NONE, and ALL). This is
290 also the recommended way to specify these ports, for compatibility
291 with OpenFlow 1.1 and later (which use the OpenFlow 1.0 numbers
292 for these ports for different purposes).
294 - Support requesting the port number with the "port_no" option in
295 the "add-if" command.
296 - ovs-pki: The "online PKI" features have been removed, along with
297 the ovs-pki-cgi program that facilitated it, because of some
298 alarmist insecurity claims. We do not believe that these claims
299 are true, but because we do not know of any users for this
300 feature it seems better on balance to remove it. (The ovs-pki-cgi
301 program was not included in distribution packaging.)
302 - ovsdb-server now enforces the immutability of immutable columns. This
303 was not enforced in earlier versions due to an oversight.
304 - The following features are now deprecated. They will be removed no
305 earlier than February 2013. Please email dev@openvswitch.org with
307 - Bridge compatibility.
309 - The autopath action.
310 - Interface type "null".
311 - Numeric values for reserved ports (see "ovs-ofctl" note above).
312 - Tunnel Path MTU Discovery.
313 - CAPWAP tunnel support.
314 - The data in the RARP packets can now be matched in the same way as the
319 ------------------------
320 *** Internal only release ***
321 - New FAQ. Please send updates and additions!
322 - Authors of controllers, please read the new section titled "Action
323 Reproduction" in DESIGN, which describes an Open vSwitch change in
324 behavior in corner cases that may affect some controllers.
326 - A new test utility that can create L3 tunnel between two Open
327 vSwitches and detect connectivity issues.
329 - New --sort and --rsort options for "dump-flows" command.
330 - "mod-port" command can now control all OpenFlow config flags.
332 - Allow general bitwise masking for IPv4 and IPv6 addresses in
333 IPv4, IPv6, and ARP packets. (Previously, only CIDR masks
335 - Allow support for arbitrary Ethernet masks. (Previously, only
336 the multicast bit in the destination address could be individually
338 - New field OXM_OF_METADATA, to align with OpenFlow 1.1.
339 - The OFPST_QUEUE request now reports an error if a specified port or
340 queue does not exist, or for requests for a specific queue on all
341 ports, if the specified queue does not exist on any port. (Previous
342 versions generally reported an empty set of results.)
343 - New "flow monitor" feature to allow controllers to be notified of
344 flow table changes as they happen.
345 - Additional protocols are not mirrored and dropped when forward-bpdu is
346 false. For a full list, see the ovs-vswitchd.conf.db man page.
347 - Open vSwitch now sends RARP packets in situations where it previously
348 sent a custom protocol, making it consistent with behavior of QEMU and
350 - All Open vSwitch programs and log files now show timestamps in UTC,
351 instead the local timezone, by default.
355 ------------------------
356 - kernel modules are renamed. openvswitch_mod.ko is now
357 openvswitch.ko and brcompat_mod.ko is now brcompat.ko.
358 - Increased the number of NXM registers to 8.
359 - Added ability to configure DSCP setting for manager and controller
360 connections. By default, these connections have a DSCP value of
361 Internetwork Control (0xc0).
362 - Added the granular link health statistics, 'cfm_health', to an
365 - Added support to mask nd_target for ICMPv6 neighbor discovery flows.
366 - Added support for OpenFlow 1.3 port description (OFPMP_PORT_DESC)
369 - Added the "dump-ports-desc" command to retrieve port
370 information using the new port description multipart messages.
372 - Added support for spawning ovs-test server from the client.
373 - Now ovs-test is able to automatically create test bridges and ports.
374 - "ovs-dpctl dump-flows" now prints observed TCP flags in TCP flows.
375 - Tripled flow setup performance.
376 - The "coverage/log" command previously available through ovs-appctl
377 has been replaced by "coverage/show". The new command replies with
378 coverage counter values, instead of logging them.
382 ------------------------
383 - Allow OFPP_CONTROLLER as the in_port for packet-out messages.
387 ------------------------
388 *** Internal only release ***
390 - LACP bonds no longer fall back to balance-slb when negotiations fail.
391 Instead they drop traffic.
392 - The default bond_mode changed from SLB to active-backup, to protect
393 unsuspecting users from the significant risks of SLB bonds (which are
394 documented in vswitchd/INTERNALS).
395 - Load balancing can be disabled by setting the bond-rebalance-interval
398 - Added support for bitwise matching on TCP and UDP ports.
399 See ovs-ofctl(8) for more information.
400 - NXM flow dumps now include times elapsed toward idle and hard
402 - Added an OpenFlow extension NXT_SET_ASYNC_CONFIG that allows
403 controllers more precise control over which OpenFlow messages they
404 receive asynchronously.
405 - New "fin_timeout" action.
406 - Added "fin_timeout" support to "learn" action.
407 - New Nicira action NXAST_CONTROLLER that offers additional features
408 over output to OFPP_CONTROLLER.
409 - When QoS settings for an interface do not configure a default queue
410 (queue 0), Open vSwitch now uses a default configuration for that
411 queue, instead of dropping all packets as in previous versions.
413 - Logging to console and file will have UTC timestamp as a default for
414 all the daemons. An example of the default format is
415 2012-01-27T16:35:17Z. ovs-appctl can be used to change the default
417 - The syntax of commands and options to set log levels was simplified,
418 to make it easier to remember.
419 - New support for limiting the number of flows in an OpenFlow flow
420 table, with configurable policy for evicting flows upon
421 overflow. See the Flow_Table table in ovs-vswitch.conf.db(5)
422 for more information.
423 - New "enable-async-messages" column in the Controller table. If set to
424 false, OpenFlow connections to the controller will initially have all
425 asynchronous messages disabled, overriding normal OpenFlow behavior.
426 - ofproto-provider interface:
427 - "struct rule" has a new member "used" that ofproto implementations
428 should maintain by updating with ofproto_rule_update_used().
430 - The new option --timestamp causes the "monitor" command to print
431 a timestamp with every update.
432 - CFM module CCM broadcasts can now be tagged with an 802.1p priority.
436 ------------------------
438 - Added support for querying, modifying, and deleting flows
439 based on flow cookie when using NXM.
440 - Added new NXM_PACKET_IN format.
441 - Added new NXAST_DEC_TTL action.
443 - Added daemonization support to the monitor and snoop commands.
445 - The "find" command supports new set relational operators
446 {=}, {!=}, {<}, {>}, {<=}, and {>=}.
447 - ovsdb-tool now uses the typical database and schema installation
448 directories as defaults.
449 - The default MAC learning timeout has been increased from 60 seconds
450 to 300 seconds. The MAC learning timeout is now configurable.
454 ------------------------
455 - Compatible with Open vSwitch kernel module included in Linux 3.3.
456 - New "VLAN splinters" feature to work around buggy device drivers
457 in old Linux versions. (This feature is deprecated. When
458 broken device drivers are no longer in widespread use, we will
459 delete this feature.) See ovs-vswitchd.conf.db(5) for more
462 - Added ability to match on IPv6 flow label through NXM.
463 - Added ability to match on ECN bits in IPv4 and IPv6 through NXM.
464 - Added ability to match on TTL in IPv4 and IPv6 through NXM.
465 - Added ability to modify ECN bits in IPv4.
466 - Added ability to modify TTL in IPv4.
468 - Don't require the "normal" action to use mirrors. Traffic will
469 now be properly mirrored for any flows, regardless of their
471 - Track packet and byte statistics sent on mirrors.
472 - The sFlow implementation can now usually infer the correct agent
473 device instead of having to be told explicitly.
475 - New "fdb/flush" command to flush bridge's MAC learning table.
477 - A new distributed testing tool that allows one to diagnose performance
478 and connectivity issues. This tool currently is not included in RH or
480 - RHEL packaging now supports integration with Red Hat network scripts.
482 - Post 1.4.*, OVS will be changing the default bond mode from balance-slb
483 to active-backup. SLB bonds carry significant risks with them
484 (documented vswitchd/INTERNALS) which we want to prevent unsuspecting
485 users from running into. Users are advised to update any scripts or
486 configuration which may be negatively impacted by explicitly setting
487 the bond mode which they want to use.
491 ------------------------
493 - Added an OpenFlow extension which allows the "output" action to accept
495 - Added an OpenFlow extension for flexible learning.
496 - Bumped number of NXM registers from four to five.
498 - New "version" command to determine version of running daemon.
499 - If no argument is provided for "cfm/show", displays detailed
500 information about all interfaces with CFM enabled.
501 - If no argument is provided for "lacp/show", displays detailed
502 information about all ports with LACP enabled.
504 - New "set-if" command to modify a datapath port's configuration.
506 - The software switch now supports 255 OpenFlow tables, instead
507 of just one. By default, only table 0 is consulted, but the
508 new NXAST_RESUBMIT_TABLE action can look up in additional
509 tables. Tables 128 and above are reserved for use by the
510 switch itself; please use only tables 0 through 127.
511 - Add support for 802.1D spanning tree (STP).
512 - Fragment handling extensions:
513 - New OFPC_FRAG_NX_MATCH fragment handling mode, in which L4
514 fields are made available for matching in fragments with
516 - New NXM_NX_IP_FRAG match field for matching IP fragments (usable
517 via "ip_frag" in ovs-ofctl).
518 - New ovs-ofctl "get-frags" and "set-frags" commands to get and set
519 fragment handling policy.
520 - CAPWAP tunneling now supports an extension to transport a 64-bit key.
521 By default it remains compatible with the old version and other
522 standards-based implementations.
523 - Flow setups are now processed in a round-robin manner across ports
524 to prevent any single client from monopolizing the CPU and conducting
525 a denial of service attack.
526 - Added support for native VLAN tagging. A new "vlan_mode"
527 parameter can be set for "port". Possible values: "access",
528 "trunk", "native-tagged" and "native-untagged".
529 - test-openflowd has been removed. Please use ovs-vswitchd instead.
532 ------------------------
533 - New "ofproto" abstraction layer to ease porting to hardware
535 - Packaging for Red Hat Enterprise Linux 5.6 and 6.0.
536 - Datapath support for Linux kernels up to 3.0.
538 - New "bundle" and "bundle_load" action extensions.
540 - Implement table unique constraints.
541 - Support cooperative locking between callers.
543 - New "-s" option for "show" command prints packet and byte
544 counters for each port.
546 - New "--readd" option for "replace-flows".
548 - New "show" command to print an overview of configuration.
549 - New "comment" command to add remark that explains intentions.
550 - ovs-brcompatd has been rewritten to fix long-standing bugs.
551 - ovs-openflowd has been renamed test-openflowd and moved into the
552 tests directory. Its presence confused too many users. Please
553 use ovs-vswitchd instead.
554 - New ovs-benchmark utility to test flow setup performance.
555 - A new log level "off" has been added. Configuring a log facility
556 "off" prevents any messages from being logged to it. Previously,
557 "emer" was effectively "off" because no messages were ever logged at
558 level "emer". Now, errors that cause a process to exit are logged
560 - "configure" option --with-l26 has been renamed --with-linux, and
561 --with-l26-source has been renamed --with-linux-source. The old
562 names will be removed after the next release, so please update
564 - The "-2.6" suffix has been dropped from the datapath/linux-2.6 and
565 datapath/linux-2.6/compat-2.6 directories.
567 - Dropped support for "tun_id_from_cookie" OpenFlow extension.
568 Please use the extensible match extensions instead.
569 - Removed the Maintenance_Point and Monitor tables in an effort
570 to simplify 802.1ag configuration.
571 - Performance and scalability improvements
575 ------------------------
576 - Ability to define policies over IPv6
579 - Support for extensible match extensions to OpenFlow
581 - Support for HFSC qdisc.
582 - Queue used by in-band control can now be configured.
584 - Kernel<->userspace interface has been reworked and should be
585 close to a stable ABI now.
586 - "Port group" concept has been dropped.
587 - GRE over IPSEC tunnels
589 - New active backup bonding mode.
590 - New L4 hashing support when LACP is enabled.
591 - Source MAC hash now includes VLAN field also.
593 - Greatly improved handling of large flow tables
595 - "show" command now prints full vport configuration.
596 - "dump-groups" command removed since kernel support for
597 port groups was dropped.
599 - New commands for working with the new Managers table.
600 - "list" command enhanced with new formatting options and --columns
602 - "get" command now accepts new --id option.
603 - New "find" command.
605 - New "queue-stats" command for printing queue stats.
606 - New commands "replace-flows" and "diff-flows".
607 - Commands to add and remove flows can now read from files.
608 - New --flow-format option to enable or disable NXM.
609 - New --more option to increase OpenFlow message verbosity.
610 - Removed "tun-cookie" command, which is no longer useful.
611 - ovs-controller enhancements for testing various features.
612 - New ovs-vlan-test command for testing for Linux kernel driver VLAN
613 bugs. New ovs-vlan-bug-workaround command for enabling and
614 disabling a workaround for these driver bugs.
616 - "Resubmit" actions now update flow statistics.
617 - New "register" extension for use in matching and actions, via NXM.
618 - New "multipath" experimental action extension.
619 - New support for matching multicast Ethernet frames, via NXM.
620 - New extension for OpenFlow vendor error codes.
621 - New extension to set the QoS output queue without actually
622 sending to an output port.
623 - Open vSwitch now reports a single flow table, instead of
624 separate hash and wildcard tables. This better models the
625 current implementation.
626 - New experimental "note" action.
627 - New "ofproto/trace" ovs-appctl command and associated utilities
628 to ease debugging complex flow tables.
630 - Schema documentation now includes an entity-relationship diagram.
631 - The database is now garbage collected. In most tables,
632 unreferenced rows will be deleted automatically.
633 - Many tables now include statistics updated periodically by
634 ovs-vswitchd or ovsdb-server.
635 - Every table now has an "external-ids" column for use by OVS
637 - There is no default controller anymore. Each bridge must have its
638 controller individually specified.
639 - The "fail-mode" is now a property of a Bridge instead of a Controller.
640 - New versioning and checksum features.
641 - New Managers table and manager_options column in Open_vSwitch table
642 for specifying managers. The old "managers" column in the
643 Open_vSwitch table has been removed.
644 - Many "name" columns are now immutable.
646 - Dropped support for XenServer pre-5.6.100.
647 - Dropped support for Linux pre-2.6.18.
648 - Dropped controller discovery support.
649 - Dropped "ovs-ofctl status" and the OpenFlow extension that it used.
650 Statistics reporting in the database is a rough equivalent.
651 - Dropped the "corekeeper" package (now separate, at
652 http://openvswitch.org/cgi-bin/gitweb.cgi?p=corekeeper).
653 - Performance and scalability improvements
656 v1.1.0pre2 - 13 Sep 2010
657 ------------------------
660 v1.1.0pre1 - 31 Aug 2010
661 ------------------------
662 - OpenFlow 1.0 slicing (QoS) functionality
663 - Python bindings for configuration database (no write support)
664 - Performance and scalability improvements
669 - New "patch" interface type
674 - Configuration database with remote management
677 - Support for XenServer 5.5 and 5.6
678 - Performance and scalability improvements
681 v0.99.2 - 18 Feb 2010
682 ---------------------
685 v0.99.1 - 25 Jan 2010
686 ---------------------
687 - Add support for sFlow(R)
688 - Make headers compatible with C++
691 v0.99.0 - 14 Jan 2010
692 ---------------------
693 - User-space forwarding engine
696 v0.90.7 - 29 Nov 2009
697 ---------------------
698 - Add support for NetFlow active timeouts
705 v0.90.5 - 21 Sep 2009
706 ---------------------
707 - Generalize in-band control to more diverse network setups