drivers/net/ethernet/stmicro/stmmac/stmmac_main.c

   1 /*******************************************************************************
   2   This is the driver for the ST MAC 10/100/1000 on-chip Ethernet controllers.
   3   ST Ethernet IPs are built around a Synopsys IP Core.
   4
   5         Copyright(C) 2007-2011 STMicroelectronics Ltd
   6
   7   This program is free software; you can redistribute it and/or modify it
   8   under the terms and conditions of the GNU General Public License,
   9   version 2, as published by the Free Software Foundation.
  10
  11   This program is distributed in the hope it will be useful, but WITHOUT
  12   ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
  13   FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
  14   more details.
  15
  16   You should have received a copy of the GNU General Public License along with
  17   this program; if not, write to the Free Software Foundation, Inc.,
  18   51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
  19
  20   The full GNU General Public License is included in this distribution in
  21   the file called "COPYING".
  22
  23   Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
  24
  25   Documentation available at:
  26         http://www.stlinux.com
  27   Support available at:
  28         https://bugzilla.stlinux.com/
  29 *******************************************************************************/
  30
  31 #include <linux/kernel.h>
  32 #include <linux/interrupt.h>
  33 #include <linux/ip.h>
  34 #include <linux/tcp.h>
  35 #include <linux/skbuff.h>
  36 #include <linux/ethtool.h>
  37 #include <linux/if_ether.h>
  38 #include <linux/crc32.h>
  39 #include <linux/mii.h>
  40 #include <linux/if.h>
  41 #include <linux/if_vlan.h>
  42 #include <linux/dma-mapping.h>
  43 #include <linux/slab.h>
  44 #include <linux/prefetch.h>
  45 #ifdef CONFIG_STMMAC_DEBUG_FS
  46 #include <linux/debugfs.h>
  47 #include <linux/seq_file.h>
  48 #endif
  49 #include "stmmac.h"
  50
  51 #undef STMMAC_DEBUG
  52 /*#define STMMAC_DEBUG*/
  53 #ifdef STMMAC_DEBUG
  54 #define DBG(nlevel, klevel, fmt, args...) \
  55                 ((void)(netif_msg_##nlevel(priv) && \
  56                 printk(KERN_##klevel fmt, ## args)))
  57 #else
  58 #define DBG(nlevel, klevel, fmt, args...) do { } while (0)
  59 #endif
  60
  61 #undef STMMAC_RX_DEBUG
  62 /*#define STMMAC_RX_DEBUG*/
  63 #ifdef STMMAC_RX_DEBUG
  64 #define RX_DBG(fmt, args...)  printk(fmt, ## args)
  65 #else
  66 #define RX_DBG(fmt, args...)  do { } while (0)
  67 #endif
  68
  69 #undef STMMAC_XMIT_DEBUG
  70 /*#define STMMAC_XMIT_DEBUG*/
  71 #ifdef STMMAC_TX_DEBUG
  72 #define TX_DBG(fmt, args...)  printk(fmt, ## args)
  73 #else
  74 #define TX_DBG(fmt, args...)  do { } while (0)
  75 #endif
  76
  77 #define STMMAC_ALIGN(x) L1_CACHE_ALIGN(x)
  78 #define JUMBO_LEN       9000
  79
  80 /* Module parameters */
  81 #define TX_TIMEO 5000 /* default 5 seconds */
  82 static int watchdog = TX_TIMEO;
  83 module_param(watchdog, int, S_IRUGO | S_IWUSR);
  84 MODULE_PARM_DESC(watchdog, "Transmit timeout in milliseconds");
  85
  86 static int debug = -1;          /* -1: default, 0: no output, 16:  all */
  87 module_param(debug, int, S_IRUGO | S_IWUSR);
  88 MODULE_PARM_DESC(debug, "Message Level (0: no output, 16: all)");
  89
  90 int phyaddr = -1;
  91 module_param(phyaddr, int, S_IRUGO);
  92 MODULE_PARM_DESC(phyaddr, "Physical device address");
  93
  94 #define DMA_TX_SIZE 256
  95 static int dma_txsize = DMA_TX_SIZE;
  96 module_param(dma_txsize, int, S_IRUGO | S_IWUSR);
  97 MODULE_PARM_DESC(dma_txsize, "Number of descriptors in the TX list");
  98
  99 #define DMA_RX_SIZE 256
 100 static int dma_rxsize = DMA_RX_SIZE;
 101 module_param(dma_rxsize, int, S_IRUGO | S_IWUSR);
 102 MODULE_PARM_DESC(dma_rxsize, "Number of descriptors in the RX list");
 103
 104 static int flow_ctrl = FLOW_OFF;
 105 module_param(flow_ctrl, int, S_IRUGO | S_IWUSR);
 106 MODULE_PARM_DESC(flow_ctrl, "Flow control ability [on/off]");
 107
 108 static int pause = PAUSE_TIME;
 109 module_param(pause, int, S_IRUGO | S_IWUSR);
 110 MODULE_PARM_DESC(pause, "Flow Control Pause Time");
 111
 112 #define TC_DEFAULT 64
 113 static int tc = TC_DEFAULT;
 114 module_param(tc, int, S_IRUGO | S_IWUSR);
 115 MODULE_PARM_DESC(tc, "DMA threshold control value");
 116
 117 /* Pay attention to tune this parameter; take care of both
 118  * hardware capability and network stabitily/performance impact.
 119  * Many tests showed that ~4ms latency seems to be good enough. */
 120 #ifdef CONFIG_STMMAC_TIMER
 121 #define DEFAULT_PERIODIC_RATE   256
 122 static int tmrate = DEFAULT_PERIODIC_RATE;
 123 module_param(tmrate, int, S_IRUGO | S_IWUSR);
 124 MODULE_PARM_DESC(tmrate, "External timer freq. (default: 256Hz)");
 125 #endif
 126
 127 #define DMA_BUFFER_SIZE BUF_SIZE_2KiB
 128 static int buf_sz = DMA_BUFFER_SIZE;
 129 module_param(buf_sz, int, S_IRUGO | S_IWUSR);
 130 MODULE_PARM_DESC(buf_sz, "DMA buffer size");
 131
 132 static const u32 default_msg_level = (NETIF_MSG_DRV | NETIF_MSG_PROBE |
 133                                       NETIF_MSG_LINK | NETIF_MSG_IFUP |
 134                                       NETIF_MSG_IFDOWN | NETIF_MSG_TIMER);
 135
 136 static irqreturn_t stmmac_interrupt(int irq, void *dev_id);
 137
 138 #ifdef CONFIG_STMMAC_DEBUG_FS
 139 static int stmmac_init_fs(struct net_device *dev);
 140 static void stmmac_exit_fs(void);
 141 #endif
 142
 143 /**
 144  * stmmac_verify_args - verify the driver parameters.
 145  * Description: it verifies if some wrong parameter is passed to the driver.
 146  * Note that wrong parameters are replaced with the default values.
 147  */
 148 static void stmmac_verify_args(void)
 149 {
 150         if (unlikely(watchdog < 0))
 151                 watchdog = TX_TIMEO;
 152         if (unlikely(dma_rxsize < 0))
 153                 dma_rxsize = DMA_RX_SIZE;
 154         if (unlikely(dma_txsize < 0))
 155                 dma_txsize = DMA_TX_SIZE;
 156         if (unlikely((buf_sz < DMA_BUFFER_SIZE) || (buf_sz > BUF_SIZE_16KiB)))
 157                 buf_sz = DMA_BUFFER_SIZE;
 158         if (unlikely(flow_ctrl > 1))
 159                 flow_ctrl = FLOW_AUTO;
 160         else if (likely(flow_ctrl < 0))
 161                 flow_ctrl = FLOW_OFF;
 162         if (unlikely((pause < 0) || (pause > 0xffff)))
 163                 pause = PAUSE_TIME;
 164 }
 165
 166 static void stmmac_clk_csr_set(struct stmmac_priv *priv)
 167 {
 168 #ifdef CONFIG_HAVE_CLK
 169         u32 clk_rate;
 170
 171         if (IS_ERR(priv->stmmac_clk))
 172                 return;
 173
 174         clk_rate = clk_get_rate(priv->stmmac_clk);
 175
 176         /* Platform provided default clk_csr would be assumed valid
 177          * for all other cases except for the below mentioned ones. */
 178         if (!(priv->clk_csr & MAC_CSR_H_FRQ_MASK)) {
 179                 if (clk_rate < CSR_F_35M)
 180                         priv->clk_csr = STMMAC_CSR_20_35M;
 181                 else if ((clk_rate >= CSR_F_35M) && (clk_rate < CSR_F_60M))
 182                         priv->clk_csr = STMMAC_CSR_35_60M;
 183                 else if ((clk_rate >= CSR_F_60M) && (clk_rate < CSR_F_100M))
 184                         priv->clk_csr = STMMAC_CSR_60_100M;
 185                 else if ((clk_rate >= CSR_F_100M) && (clk_rate < CSR_F_150M))
 186                         priv->clk_csr = STMMAC_CSR_100_150M;
 187                 else if ((clk_rate >= CSR_F_150M) && (clk_rate < CSR_F_250M))
 188                         priv->clk_csr = STMMAC_CSR_150_250M;
 189                 else if ((clk_rate >= CSR_F_250M) && (clk_rate < CSR_F_300M))
 190                         priv->clk_csr = STMMAC_CSR_250_300M;
 191         } /* For values higher than the IEEE 802.3 specified frequency
 192            * we can not estimate the proper divider as it is not known
 193            * the frequency of clk_csr_i. So we do not change the default
 194            * divider. */
 195 #endif
 196 }
 197
 198 #if defined(STMMAC_XMIT_DEBUG) || defined(STMMAC_RX_DEBUG)
 199 static void print_pkt(unsigned char *buf, int len)
 200 {
 201         int j;
 202         pr_info("len = %d byte, buf addr: 0x%p", len, buf);
 203         for (j = 0; j < len; j++) {
 204                 if ((j % 16) == 0)
 205                         pr_info("\n %03x:", j);
 206                 pr_info(" %02x", buf[j]);
 207         }
 208         pr_info("\n");
 209 }
 210 #endif
 211
 212 /* minimum number of free TX descriptors required to wake up TX process */
 213 #define STMMAC_TX_THRESH(x)     (x->dma_tx_size/4)
 214
 215 static inline u32 stmmac_tx_avail(struct stmmac_priv *priv)
 216 {
 217         return priv->dirty_tx + priv->dma_tx_size - priv->cur_tx - 1;
 218 }
 219
 220 /* On some ST platforms, some HW system configuraton registers have to be
 221  * set according to the link speed negotiated.
 222  */
 223 static inline void stmmac_hw_fix_mac_speed(struct stmmac_priv *priv)
 224 {
 225         struct phy_device *phydev = priv->phydev;
 226
 227         if (likely(priv->plat->fix_mac_speed))
 228                 priv->plat->fix_mac_speed(priv->plat->bsp_priv,
 229                                           phydev->speed);
 230 }
 231
 232 /**
 233  * stmmac_adjust_link
 234  * @dev: net device structure
 235  * Description: it adjusts the link parameters.
 236  */
 237 static void stmmac_adjust_link(struct net_device *dev)
 238 {
 239         struct stmmac_priv *priv = netdev_priv(dev);
 240         struct phy_device *phydev = priv->phydev;
 241         unsigned long flags;
 242         int new_state = 0;
 243         unsigned int fc = priv->flow_ctrl, pause_time = priv->pause;
 244
 245         if (phydev == NULL)
 246                 return;
 247
 248         DBG(probe, DEBUG, "stmmac_adjust_link: called.  address %d link %d\n",
 249             phydev->addr, phydev->link);
 250
 251         spin_lock_irqsave(&priv->lock, flags);
 252         if (phydev->link) {
 253                 u32 ctrl = readl(priv->ioaddr + MAC_CTRL_REG);
 254
 255                 /* Now we make sure that we can be in full duplex mode.
 256                  * If not, we operate in half-duplex mode. */
 257                 if (phydev->duplex != priv->oldduplex) {
 258                         new_state = 1;
 259                         if (!(phydev->duplex))
 260                                 ctrl &= ~priv->hw->link.duplex;
 261                         else
 262                                 ctrl |= priv->hw->link.duplex;
 263                         priv->oldduplex = phydev->duplex;
 264                 }
 265                 /* Flow Control operation */
 266                 if (phydev->pause)
 267                         priv->hw->mac->flow_ctrl(priv->ioaddr, phydev->duplex,
 268                                                  fc, pause_time);
 269
 270                 if (phydev->speed != priv->speed) {
 271                         new_state = 1;
 272                         switch (phydev->speed) {
 273                         case 1000:
 274                                 if (likely(priv->plat->has_gmac))
 275                                         ctrl &= ~priv->hw->link.port;
 276                                         stmmac_hw_fix_mac_speed(priv);
 277                                 break;
 278                         case 100:
 279                         case 10:
 280                                 if (priv->plat->has_gmac) {
 281                                         ctrl |= priv->hw->link.port;
 282                                         if (phydev->speed == SPEED_100) {
 283                                                 ctrl |= priv->hw->link.speed;
 284                                         } else {
 285                                                 ctrl &= ~(priv->hw->link.speed);
 286                                         }
 287                                 } else {
 288                                         ctrl &= ~priv->hw->link.port;
 289                                 }
 290                                 stmmac_hw_fix_mac_speed(priv);
 291                                 break;
 292                         default:
 293                                 if (netif_msg_link(priv))
 294                                         pr_warning("%s: Speed (%d) is not 10"
 295                                        " or 100!\n", dev->name, phydev->speed);
 296                                 break;
 297                         }
 298
 299                         priv->speed = phydev->speed;
 300                 }
 301
 302                 writel(ctrl, priv->ioaddr + MAC_CTRL_REG);
 303
 304                 if (!priv->oldlink) {
 305                         new_state = 1;
 306                         priv->oldlink = 1;
 307                 }
 308         } else if (priv->oldlink) {
 309                 new_state = 1;
 310                 priv->oldlink = 0;
 311                 priv->speed = 0;
 312                 priv->oldduplex = -1;
 313         }
 314
 315         if (new_state && netif_msg_link(priv))
 316                 phy_print_status(phydev);
 317
 318         spin_unlock_irqrestore(&priv->lock, flags);
 319
 320         DBG(probe, DEBUG, "stmmac_adjust_link: exiting\n");
 321 }
 322
 323 /**
 324  * stmmac_init_phy - PHY initialization
 325  * @dev: net device structure
 326  * Description: it initializes the driver's PHY state, and attaches the PHY
 327  * to the mac driver.
 328  *  Return value:
 329  *  0 on success
 330  */
 331 static int stmmac_init_phy(struct net_device *dev)
 332 {
 333         struct stmmac_priv *priv = netdev_priv(dev);
 334         struct phy_device *phydev;
 335         char phy_id[MII_BUS_ID_SIZE + 3];
 336         char bus_id[MII_BUS_ID_SIZE];
 337         int interface = priv->plat->interface;
 338         priv->oldlink = 0;
 339         priv->speed = 0;
 340         priv->oldduplex = -1;
 341
 342         if (priv->plat->phy_bus_name)
 343                 snprintf(bus_id, MII_BUS_ID_SIZE, "%s-%x",
 344                                 priv->plat->phy_bus_name, priv->plat->bus_id);
 345         else
 346                 snprintf(bus_id, MII_BUS_ID_SIZE, "stmmac-%x",
 347                                 priv->plat->bus_id);
 348
 349         snprintf(phy_id, MII_BUS_ID_SIZE + 3, PHY_ID_FMT, bus_id,
 350                  priv->plat->phy_addr);
 351         pr_debug("stmmac_init_phy:  trying to attach to %s\n", phy_id);
 352
 353         phydev = phy_connect(dev, phy_id, &stmmac_adjust_link, 0, interface);
 354
 355         if (IS_ERR(phydev)) {
 356                 pr_err("%s: Could not attach to PHY\n", dev->name);
 357                 return PTR_ERR(phydev);
 358         }
 359
 360         /* Stop Advertising 1000BASE Capability if interface is not GMII */
 361         if ((interface == PHY_INTERFACE_MODE_MII) ||
 362             (interface == PHY_INTERFACE_MODE_RMII))
 363                 phydev->advertising &= ~(SUPPORTED_1000baseT_Half |
 364                                          SUPPORTED_1000baseT_Full);
 365
 366         /*
 367          * Broken HW is sometimes missing the pull-up resistor on the
 368          * MDIO line, which results in reads to non-existent devices returning
 369          * 0 rather than 0xffff. Catch this here and treat 0 as a non-existent
 370          * device as well.
 371          * Note: phydev->phy_id is the result of reading the UID PHY registers.
 372          */
 373         if (phydev->phy_id == 0) {
 374                 phy_disconnect(phydev);
 375                 return -ENODEV;
 376         }
 377         pr_debug("stmmac_init_phy:  %s: attached to PHY (UID 0x%x)"
 378                  " Link = %d\n", dev->name, phydev->phy_id, phydev->link);
 379
 380         priv->phydev = phydev;
 381
 382         return 0;
 383 }
 384
 385 /**
 386  * display_ring
 387  * @p: pointer to the ring.
 388  * @size: size of the ring.
 389  * Description: display all the descriptors within the ring.
 390  */
 391 static void display_ring(struct dma_desc *p, int size)
 392 {
 393         struct tmp_s {
 394                 u64 a;
 395                 unsigned int b;
 396                 unsigned int c;
 397         };
 398         int i;
 399         for (i = 0; i < size; i++) {
 400                 struct tmp_s *x = (struct tmp_s *)(p + i);
 401                 pr_info("\t%d [0x%x]: DES0=0x%x DES1=0x%x BUF1=0x%x BUF2=0x%x",
 402                        i, (unsigned int)virt_to_phys(&p[i]),
 403                        (unsigned int)(x->a), (unsigned int)((x->a) >> 32),
 404                        x->b, x->c);
 405                 pr_info("\n");
 406         }
 407 }
 408
 409 static int stmmac_set_bfsize(int mtu, int bufsize)
 410 {
 411         int ret = bufsize;
 412
 413         if (mtu >= BUF_SIZE_4KiB)
 414                 ret = BUF_SIZE_8KiB;
 415         else if (mtu >= BUF_SIZE_2KiB)
 416                 ret = BUF_SIZE_4KiB;
 417         else if (mtu >= DMA_BUFFER_SIZE)
 418                 ret = BUF_SIZE_2KiB;
 419         else
 420                 ret = DMA_BUFFER_SIZE;
 421
 422         return ret;
 423 }
 424
 425 /**
 426  * init_dma_desc_rings - init the RX/TX descriptor rings
 427  * @dev: net device structure
 428  * Description:  this function initializes the DMA RX/TX descriptors
 429  * and allocates the socket buffers. It suppors the chained and ring
 430  * modes.
 431  */
 432 static void init_dma_desc_rings(struct net_device *dev)
 433 {
 434         int i;
 435         struct stmmac_priv *priv = netdev_priv(dev);
 436         struct sk_buff *skb;
 437         unsigned int txsize = priv->dma_tx_size;
 438         unsigned int rxsize = priv->dma_rx_size;
 439         unsigned int bfsize;
 440         int dis_ic = 0;
 441         int des3_as_data_buf = 0;
 442
 443         /* Set the max buffer size according to the DESC mode
 444          * and the MTU. Note that RING mode allows 16KiB bsize. */
 445         bfsize = priv->hw->ring->set_16kib_bfsize(dev->mtu);
 446
 447         if (bfsize == BUF_SIZE_16KiB)
 448                 des3_as_data_buf = 1;
 449         else
 450                 bfsize = stmmac_set_bfsize(dev->mtu, priv->dma_buf_sz);
 451
 452 #ifdef CONFIG_STMMAC_TIMER
 453         /* Disable interrupts on completion for the reception if timer is on */
 454         if (likely(priv->tm->enable))
 455                 dis_ic = 1;
 456 #endif
 457
 458         DBG(probe, INFO, "stmmac: txsize %d, rxsize %d, bfsize %d\n",
 459             txsize, rxsize, bfsize);
 460
 461         priv->rx_skbuff_dma = kmalloc(rxsize * sizeof(dma_addr_t), GFP_KERNEL);
 462         priv->rx_skbuff =
 463             kmalloc(sizeof(struct sk_buff *) * rxsize, GFP_KERNEL);
 464         priv->dma_rx =
 465             (struct dma_desc *)dma_alloc_coherent(priv->device,
 466                                                   rxsize *
 467                                                   sizeof(struct dma_desc),
 468                                                   &priv->dma_rx_phy,
 469                                                   GFP_KERNEL);
 470         priv->tx_skbuff = kmalloc(sizeof(struct sk_buff *) * txsize,
 471                                        GFP_KERNEL);
 472         priv->dma_tx =
 473             (struct dma_desc *)dma_alloc_coherent(priv->device,
 474                                                   txsize *
 475                                                   sizeof(struct dma_desc),
 476                                                   &priv->dma_tx_phy,
 477                                                   GFP_KERNEL);
 478
 479         if ((priv->dma_rx == NULL) || (priv->dma_tx == NULL)) {
 480                 pr_err("%s:ERROR allocating the DMA Tx/Rx desc\n", __func__);
 481                 return;
 482         }
 483
 484         DBG(probe, INFO, "stmmac (%s) DMA desc: virt addr (Rx %p, "
 485             "Tx %p)\n\tDMA phy addr (Rx 0x%08x, Tx 0x%08x)\n",
 486             dev->name, priv->dma_rx, priv->dma_tx,
 487             (unsigned int)priv->dma_rx_phy, (unsigned int)priv->dma_tx_phy);
 488
 489         /* RX INITIALIZATION */
 490         DBG(probe, INFO, "stmmac: SKB addresses:\n"
 491                          "skb\t\tskb data\tdma data\n");
 492
 493         for (i = 0; i < rxsize; i++) {
 494                 struct dma_desc *p = priv->dma_rx + i;
 495
 496                 skb = __netdev_alloc_skb(dev, bfsize + NET_IP_ALIGN,
 497                                          GFP_KERNEL);
 498                 if (unlikely(skb == NULL)) {
 499                         pr_err("%s: Rx init fails; skb is NULL\n", __func__);
 500                         break;
 501                 }
 502                 skb_reserve(skb, NET_IP_ALIGN);
 503                 priv->rx_skbuff[i] = skb;
 504                 priv->rx_skbuff_dma[i] = dma_map_single(priv->device, skb->data,
 505                                                 bfsize, DMA_FROM_DEVICE);
 506
 507                 p->des2 = priv->rx_skbuff_dma[i];
 508
 509                 priv->hw->ring->init_desc3(des3_as_data_buf, p);
 510
 511                 DBG(probe, INFO, "[%p]\t[%p]\t[%x]\n", priv->rx_skbuff[i],
 512                         priv->rx_skbuff[i]->data, priv->rx_skbuff_dma[i]);
 513         }
 514         priv->cur_rx = 0;
 515         priv->dirty_rx = (unsigned int)(i - rxsize);
 516         priv->dma_buf_sz = bfsize;
 517         buf_sz = bfsize;
 518
 519         /* TX INITIALIZATION */
 520         for (i = 0; i < txsize; i++) {
 521                 priv->tx_skbuff[i] = NULL;
 522                 priv->dma_tx[i].des2 = 0;
 523         }
 524
 525         /* In case of Chained mode this sets the des3 to the next
 526          * element in the chain */
 527         priv->hw->ring->init_dma_chain(priv->dma_rx, priv->dma_rx_phy, rxsize);
 528         priv->hw->ring->init_dma_chain(priv->dma_tx, priv->dma_tx_phy, txsize);
 529
 530         priv->dirty_tx = 0;
 531         priv->cur_tx = 0;
 532
 533         /* Clear the Rx/Tx descriptors */
 534         priv->hw->desc->init_rx_desc(priv->dma_rx, rxsize, dis_ic);
 535         priv->hw->desc->init_tx_desc(priv->dma_tx, txsize);
 536
 537         if (netif_msg_hw(priv)) {
 538                 pr_info("RX descriptor ring:\n");
 539                 display_ring(priv->dma_rx, rxsize);
 540                 pr_info("TX descriptor ring:\n");
 541                 display_ring(priv->dma_tx, txsize);
 542         }
 543 }
 544
 545 static void dma_free_rx_skbufs(struct stmmac_priv *priv)
 546 {
 547         int i;
 548
 549         for (i = 0; i < priv->dma_rx_size; i++) {
 550                 if (priv->rx_skbuff[i]) {
 551                         dma_unmap_single(priv->device, priv->rx_skbuff_dma[i],
 552                                          priv->dma_buf_sz, DMA_FROM_DEVICE);
 553                         dev_kfree_skb_any(priv->rx_skbuff[i]);
 554                 }
 555                 priv->rx_skbuff[i] = NULL;
 556         }
 557 }
 558
 559 static void dma_free_tx_skbufs(struct stmmac_priv *priv)
 560 {
 561         int i;
 562
 563         for (i = 0; i < priv->dma_tx_size; i++) {
 564                 if (priv->tx_skbuff[i] != NULL) {
 565                         struct dma_desc *p = priv->dma_tx + i;
 566                         if (p->des2)
 567                                 dma_unmap_single(priv->device, p->des2,
 568                                                  priv->hw->desc->get_tx_len(p),
 569                                                  DMA_TO_DEVICE);
 570                         dev_kfree_skb_any(priv->tx_skbuff[i]);
 571                         priv->tx_skbuff[i] = NULL;
 572                 }
 573         }
 574 }
 575
 576 static void free_dma_desc_resources(struct stmmac_priv *priv)
 577 {
 578         /* Release the DMA TX/RX socket buffers */
 579         dma_free_rx_skbufs(priv);
 580         dma_free_tx_skbufs(priv);
 581
 582         /* Free the region of consistent memory previously allocated for
 583          * the DMA */
 584         dma_free_coherent(priv->device,
 585                           priv->dma_tx_size * sizeof(struct dma_desc),
 586                           priv->dma_tx, priv->dma_tx_phy);
 587         dma_free_coherent(priv->device,
 588                           priv->dma_rx_size * sizeof(struct dma_desc),
 589                           priv->dma_rx, priv->dma_rx_phy);
 590         kfree(priv->rx_skbuff_dma);
 591         kfree(priv->rx_skbuff);
 592         kfree(priv->tx_skbuff);
 593 }
 594
 595 /**
 596  *  stmmac_dma_operation_mode - HW DMA operation mode
 597  *  @priv : pointer to the private device structure.
 598  *  Description: it sets the DMA operation mode: tx/rx DMA thresholds
 599  *  or Store-And-Forward capability.
 600  */
 601 static void stmmac_dma_operation_mode(struct stmmac_priv *priv)
 602 {
 603         if (likely(priv->plat->force_sf_dma_mode ||
 604                 ((priv->plat->tx_coe) && (!priv->no_csum_insertion)))) {
 605                 /*
 606                  * In case of GMAC, SF mode can be enabled
 607                  * to perform the TX COE in HW. This depends on:
 608                  * 1) TX COE if actually supported
 609                  * 2) There is no bugged Jumbo frame support
 610                  *    that needs to not insert csum in the TDES.
 611                  */
 612                 priv->hw->dma->dma_mode(priv->ioaddr,
 613                                         SF_DMA_MODE, SF_DMA_MODE);
 614                 tc = SF_DMA_MODE;
 615         } else
 616                 priv->hw->dma->dma_mode(priv->ioaddr, tc, SF_DMA_MODE);
 617 }
 618
 619 /**
 620  * stmmac_tx:
 621  * @priv: private driver structure
 622  * Description: it reclaims resources after transmission completes.
 623  */
 624 static void stmmac_tx(struct stmmac_priv *priv)
 625 {
 626         unsigned int txsize = priv->dma_tx_size;
 627
 628         spin_lock(&priv->tx_lock);
 629
 630         while (priv->dirty_tx != priv->cur_tx) {
 631                 int last;
 632                 unsigned int entry = priv->dirty_tx % txsize;
 633                 struct sk_buff *skb = priv->tx_skbuff[entry];
 634                 struct dma_desc *p = priv->dma_tx + entry;
 635
 636                 /* Check if the descriptor is owned by the DMA. */
 637                 if (priv->hw->desc->get_tx_owner(p))
 638                         break;
 639
 640                 /* Verify tx error by looking at the last segment */
 641                 last = priv->hw->desc->get_tx_ls(p);
 642                 if (likely(last)) {
 643                         int tx_error =
 644                                 priv->hw->desc->tx_status(&priv->dev->stats,
 645                                                           &priv->xstats, p,
 646                                                           priv->ioaddr);
 647                         if (likely(tx_error == 0)) {
 648                                 priv->dev->stats.tx_packets++;
 649                                 priv->xstats.tx_pkt_n++;
 650                         } else
 651                                 priv->dev->stats.tx_errors++;
 652                 }
 653                 TX_DBG("%s: curr %d, dirty %d\n", __func__,
 654                         priv->cur_tx, priv->dirty_tx);
 655
 656                 if (likely(p->des2))
 657                         dma_unmap_single(priv->device, p->des2,
 658                                          priv->hw->desc->get_tx_len(p),
 659                                          DMA_TO_DEVICE);
 660                 priv->hw->ring->clean_desc3(p);
 661
 662                 if (likely(skb != NULL)) {
 663                         /*
 664                          * If there's room in the queue (limit it to size)
 665                          * we add this skb back into the pool,
 666                          * if it's the right size.
 667                          */
 668                         if ((skb_queue_len(&priv->rx_recycle) <
 669                                 priv->dma_rx_size) &&
 670                                 skb_recycle_check(skb, priv->dma_buf_sz))
 671                                 __skb_queue_head(&priv->rx_recycle, skb);
 672                         else
 673                                 dev_kfree_skb(skb);
 674
 675                         priv->tx_skbuff[entry] = NULL;
 676                 }
 677
 678                 priv->hw->desc->release_tx_desc(p);
 679
 680                 priv->dirty_tx++;
 681         }
 682         if (unlikely(netif_queue_stopped(priv->dev) &&
 683                      stmmac_tx_avail(priv) > STMMAC_TX_THRESH(priv))) {
 684                 netif_tx_lock(priv->dev);
 685                 if (netif_queue_stopped(priv->dev) &&
 686                      stmmac_tx_avail(priv) > STMMAC_TX_THRESH(priv)) {
 687                         TX_DBG("%s: restart transmit\n", __func__);
 688                         netif_wake_queue(priv->dev);
 689                 }
 690                 netif_tx_unlock(priv->dev);
 691         }
 692         spin_unlock(&priv->tx_lock);
 693 }
 694
 695 static inline void stmmac_enable_irq(struct stmmac_priv *priv)
 696 {
 697 #ifdef CONFIG_STMMAC_TIMER
 698         if (likely(priv->tm->enable))
 699                 priv->tm->timer_start(tmrate);
 700         else
 701 #endif
 702                 priv->hw->dma->enable_dma_irq(priv->ioaddr);
 703 }
 704
 705 static inline void stmmac_disable_irq(struct stmmac_priv *priv)
 706 {
 707 #ifdef CONFIG_STMMAC_TIMER
 708         if (likely(priv->tm->enable))
 709                 priv->tm->timer_stop();
 710         else
 711 #endif
 712                 priv->hw->dma->disable_dma_irq(priv->ioaddr);
 713 }
 714
 715 static int stmmac_has_work(struct stmmac_priv *priv)
 716 {
 717         unsigned int has_work = 0;
 718         int rxret, tx_work = 0;
 719
 720         rxret = priv->hw->desc->get_rx_owner(priv->dma_rx +
 721                 (priv->cur_rx % priv->dma_rx_size));
 722
 723         if (priv->dirty_tx != priv->cur_tx)
 724                 tx_work = 1;
 725
 726         if (likely(!rxret || tx_work))
 727                 has_work = 1;
 728
 729         return has_work;
 730 }
 731
 732 static inline void _stmmac_schedule(struct stmmac_priv *priv)
 733 {
 734         if (likely(stmmac_has_work(priv))) {
 735                 stmmac_disable_irq(priv);
 736                 napi_schedule(&priv->napi);
 737         }
 738 }
 739
 740 #ifdef CONFIG_STMMAC_TIMER
 741 void stmmac_schedule(struct net_device *dev)
 742 {
 743         struct stmmac_priv *priv = netdev_priv(dev);
 744
 745         priv->xstats.sched_timer_n++;
 746
 747         _stmmac_schedule(priv);
 748 }
 749
 750 static void stmmac_no_timer_started(unsigned int x)
 751 {;
 752 };
 753
 754 static void stmmac_no_timer_stopped(void)
 755 {;
 756 };
 757 #endif
 758
 759 /**
 760  * stmmac_tx_err:
 761  * @priv: pointer to the private device structure
 762  * Description: it cleans the descriptors and restarts the transmission
 763  * in case of errors.
 764  */
 765 static void stmmac_tx_err(struct stmmac_priv *priv)
 766 {
 767         netif_stop_queue(priv->dev);
 768
 769         priv->hw->dma->stop_tx(priv->ioaddr);
 770         dma_free_tx_skbufs(priv);
 771         priv->hw->desc->init_tx_desc(priv->dma_tx, priv->dma_tx_size);
 772         priv->dirty_tx = 0;
 773         priv->cur_tx = 0;
 774         priv->hw->dma->start_tx(priv->ioaddr);
 775
 776         priv->dev->stats.tx_errors++;
 777         netif_wake_queue(priv->dev);
 778 }
 779
 780
 781 static void stmmac_dma_interrupt(struct stmmac_priv *priv)
 782 {
 783         int status;
 784
 785         status = priv->hw->dma->dma_interrupt(priv->ioaddr, &priv->xstats);
 786         if (likely(status == handle_tx_rx))
 787                 _stmmac_schedule(priv);
 788
 789         else if (unlikely(status == tx_hard_error_bump_tc)) {
 790                 /* Try to bump up the dma threshold on this failure */
 791                 if (unlikely(tc != SF_DMA_MODE) && (tc <= 256)) {
 792                         tc += 64;
 793                         priv->hw->dma->dma_mode(priv->ioaddr, tc, SF_DMA_MODE);
 794                         priv->xstats.threshold = tc;
 795                 }
 796         } else if (unlikely(status == tx_hard_error))
 797                 stmmac_tx_err(priv);
 798 }
 799
 800 static void stmmac_mmc_setup(struct stmmac_priv *priv)
 801 {
 802         unsigned int mode = MMC_CNTRL_RESET_ON_READ | MMC_CNTRL_COUNTER_RESET |
 803                             MMC_CNTRL_PRESET | MMC_CNTRL_FULL_HALF_PRESET;
 804
 805         /* Mask MMC irq, counters are managed in SW and registers
 806          * are cleared on each READ eventually. */
 807         dwmac_mmc_intr_all_mask(priv->ioaddr);
 808
 809         if (priv->dma_cap.rmon) {
 810                 dwmac_mmc_ctrl(priv->ioaddr, mode);
 811                 memset(&priv->mmc, 0, sizeof(struct stmmac_counters));
 812         } else
 813                 pr_info(" No MAC Management Counters available\n");
 814 }
 815
 816 static u32 stmmac_get_synopsys_id(struct stmmac_priv *priv)
 817 {
 818         u32 hwid = priv->hw->synopsys_uid;
 819
 820         /* Only check valid Synopsys Id because old MAC chips
 821          * have no HW registers where get the ID */
 822         if (likely(hwid)) {
 823                 u32 uid = ((hwid & 0x0000ff00) >> 8);
 824                 u32 synid = (hwid & 0x000000ff);
 825
 826                 pr_info("stmmac - user ID: 0x%x, Synopsys ID: 0x%x\n",
 827                         uid, synid);
 828
 829                 return synid;
 830         }
 831         return 0;
 832 }
 833
 834 /**
 835  * stmmac_selec_desc_mode
 836  * @priv : private structure
 837  * Description: select the Enhanced/Alternate or Normal descriptors
 838  */
 839 static void stmmac_selec_desc_mode(struct stmmac_priv *priv)
 840 {
 841         if (priv->plat->enh_desc) {
 842                 pr_info(" Enhanced/Alternate descriptors\n");
 843                 priv->hw->desc = &enh_desc_ops;
 844         } else {
 845                 pr_info(" Normal descriptors\n");
 846                 priv->hw->desc = &ndesc_ops;
 847         }
 848 }
 849
 850 /**
 851  * stmmac_get_hw_features
 852  * @priv : private device pointer
 853  * Description:
 854  *  new GMAC chip generations have a new register to indicate the
 855  *  presence of the optional feature/functions.
 856  *  This can be also used to override the value passed through the
 857  *  platform and necessary for old MAC10/100 and GMAC chips.
 858  */
 859 static int stmmac_get_hw_features(struct stmmac_priv *priv)
 860 {
 861         u32 hw_cap = 0;
 862
 863         if (priv->hw->dma->get_hw_feature) {
 864                 hw_cap = priv->hw->dma->get_hw_feature(priv->ioaddr);
 865
 866                 priv->dma_cap.mbps_10_100 = (hw_cap & DMA_HW_FEAT_MIISEL);
 867                 priv->dma_cap.mbps_1000 = (hw_cap & DMA_HW_FEAT_GMIISEL) >> 1;
 868                 priv->dma_cap.half_duplex = (hw_cap & DMA_HW_FEAT_HDSEL) >> 2;
 869                 priv->dma_cap.hash_filter = (hw_cap & DMA_HW_FEAT_HASHSEL) >> 4;
 870                 priv->dma_cap.multi_addr =
 871                         (hw_cap & DMA_HW_FEAT_ADDMACADRSEL) >> 5;
 872                 priv->dma_cap.pcs = (hw_cap & DMA_HW_FEAT_PCSSEL) >> 6;
 873                 priv->dma_cap.sma_mdio = (hw_cap & DMA_HW_FEAT_SMASEL) >> 8;
 874                 priv->dma_cap.pmt_remote_wake_up =
 875                         (hw_cap & DMA_HW_FEAT_RWKSEL) >> 9;
 876                 priv->dma_cap.pmt_magic_frame =
 877                         (hw_cap & DMA_HW_FEAT_MGKSEL) >> 10;
 878                 /* MMC */
 879                 priv->dma_cap.rmon = (hw_cap & DMA_HW_FEAT_MMCSEL) >> 11;
 880                 /* IEEE 1588-2002*/
 881                 priv->dma_cap.time_stamp =
 882                         (hw_cap & DMA_HW_FEAT_TSVER1SEL) >> 12;
 883                 /* IEEE 1588-2008*/
 884                 priv->dma_cap.atime_stamp =
 885                         (hw_cap & DMA_HW_FEAT_TSVER2SEL) >> 13;
 886                 /* 802.3az - Energy-Efficient Ethernet (EEE) */
 887                 priv->dma_cap.eee = (hw_cap & DMA_HW_FEAT_EEESEL) >> 14;
 888                 priv->dma_cap.av = (hw_cap & DMA_HW_FEAT_AVSEL) >> 15;
 889                 /* TX and RX csum */
 890                 priv->dma_cap.tx_coe = (hw_cap & DMA_HW_FEAT_TXCOESEL) >> 16;
 891                 priv->dma_cap.rx_coe_type1 =
 892                         (hw_cap & DMA_HW_FEAT_RXTYP1COE) >> 17;
 893                 priv->dma_cap.rx_coe_type2 =
 894                         (hw_cap & DMA_HW_FEAT_RXTYP2COE) >> 18;
 895                 priv->dma_cap.rxfifo_over_2048 =
 896                         (hw_cap & DMA_HW_FEAT_RXFIFOSIZE) >> 19;
 897                 /* TX and RX number of channels */
 898                 priv->dma_cap.number_rx_channel =
 899                         (hw_cap & DMA_HW_FEAT_RXCHCNT) >> 20;
 900                 priv->dma_cap.number_tx_channel =
 901                         (hw_cap & DMA_HW_FEAT_TXCHCNT) >> 22;
 902                 /* Alternate (enhanced) DESC mode*/
 903                 priv->dma_cap.enh_desc =
 904                         (hw_cap & DMA_HW_FEAT_ENHDESSEL) >> 24;
 905
 906         }
 907
 908         return hw_cap;
 909 }
 910
 911 static void stmmac_check_ether_addr(struct stmmac_priv *priv)
 912 {
 913         /* verify if the MAC address is valid, in case of failures it
 914          * generates a random MAC address */
 915         if (!is_valid_ether_addr(priv->dev->dev_addr)) {
 916                 priv->hw->mac->get_umac_addr((void __iomem *)
 917                                              priv->dev->base_addr,
 918                                              priv->dev->dev_addr, 0);
 919                 if  (!is_valid_ether_addr(priv->dev->dev_addr))
 920                         eth_hw_addr_random(priv->dev);
 921         }
 922         pr_warning("%s: device MAC address %pM\n", priv->dev->name,
 923                                                    priv->dev->dev_addr);
 924 }
 925
 926 static int stmmac_init_dma_engine(struct stmmac_priv *priv)
 927 {
 928         int pbl = DEFAULT_DMA_PBL, fixed_burst = 0, burst_len = 0;
 929         int mixed_burst = 0;
 930
 931         /* Some DMA parameters can be passed from the platform;
 932          * in case of these are not passed we keep a default
 933          * (good for all the chips) and init the DMA! */
 934         if (priv->plat->dma_cfg) {
 935                 pbl = priv->plat->dma_cfg->pbl;
 936                 fixed_burst = priv->plat->dma_cfg->fixed_burst;
 937                 mixed_burst = priv->plat->dma_cfg->mixed_burst;
 938                 burst_len = priv->plat->dma_cfg->burst_len;
 939         }
 940
 941         return priv->hw->dma->init(priv->ioaddr, pbl, fixed_burst, mixed_burst,
 942                                    burst_len, priv->dma_tx_phy,
 943                                    priv->dma_rx_phy);
 944 }
 945
 946 /**
 947  *  stmmac_open - open entry point of the driver
 948  *  @dev : pointer to the device structure.
 949  *  Description:
 950  *  This function is the open entry point of the driver.
 951  *  Return value:
 952  *  0 on success and an appropriate (-)ve integer as defined in errno.h
 953  *  file on failure.
 954  */
 955 static int stmmac_open(struct net_device *dev)
 956 {
 957         struct stmmac_priv *priv = netdev_priv(dev);
 958         int ret;
 959
 960 #ifdef CONFIG_STMMAC_TIMER
 961         priv->tm = kzalloc(sizeof(struct stmmac_timer *), GFP_KERNEL);
 962         if (unlikely(priv->tm == NULL))
 963                 return -ENOMEM;
 964
 965         priv->tm->freq = tmrate;
 966
 967         /* Test if the external timer can be actually used.
 968          * In case of failure continue without timer. */
 969         if (unlikely((stmmac_open_ext_timer(dev, priv->tm)) < 0)) {
 970                 pr_warning("stmmaceth: cannot attach the external timer.\n");
 971                 priv->tm->freq = 0;
 972                 priv->tm->timer_start = stmmac_no_timer_started;
 973                 priv->tm->timer_stop = stmmac_no_timer_stopped;
 974         } else
 975                 priv->tm->enable = 1;
 976 #endif
 977         stmmac_clk_enable(priv);
 978
 979         stmmac_check_ether_addr(priv);
 980
 981         ret = stmmac_init_phy(dev);
 982         if (unlikely(ret)) {
 983                 pr_err("%s: Cannot attach to PHY (error: %d)\n", __func__, ret);
 984                 goto open_error;
 985         }
 986
 987         /* Create and initialize the TX/RX descriptors chains. */
 988         priv->dma_tx_size = STMMAC_ALIGN(dma_txsize);
 989         priv->dma_rx_size = STMMAC_ALIGN(dma_rxsize);
 990         priv->dma_buf_sz = STMMAC_ALIGN(buf_sz);
 991         init_dma_desc_rings(dev);
 992
 993         /* DMA initialization and SW reset */
 994         ret = stmmac_init_dma_engine(priv);
 995         if (ret < 0) {
 996                 pr_err("%s: DMA initialization failed\n", __func__);
 997                 goto open_error;
 998         }
 999
1000         /* Copy the MAC addr into the HW  */
1001         priv->hw->mac->set_umac_addr(priv->ioaddr, dev->dev_addr, 0);
1002
1003         /* If required, perform hw setup of the bus. */
1004         if (priv->plat->bus_setup)
1005                 priv->plat->bus_setup(priv->ioaddr);
1006
1007         /* Initialize the MAC Core */
1008         priv->hw->mac->core_init(priv->ioaddr);
1009
1010         /* Request the IRQ lines */
1011         ret = request_irq(dev->irq, stmmac_interrupt,
1012                          IRQF_SHARED, dev->name, dev);
1013         if (unlikely(ret < 0)) {
1014                 pr_err("%s: ERROR: allocating the IRQ %d (error: %d)\n",
1015                        __func__, dev->irq, ret);
1016                 goto open_error;
1017         }
1018
1019         /* Request the Wake IRQ in case of another line is used for WoL */
1020         if (priv->wol_irq != dev->irq) {
1021                 ret = request_irq(priv->wol_irq, stmmac_interrupt,
1022                                   IRQF_SHARED, dev->name, dev);
1023                 if (unlikely(ret < 0)) {
1024                         pr_err("%s: ERROR: allocating the ext WoL IRQ %d "
1025                                "(error: %d)\n", __func__, priv->wol_irq, ret);
1026                         goto open_error_wolirq;
1027                 }
1028         }
1029
1030         /* Enable the MAC Rx/Tx */
1031         stmmac_set_mac(priv->ioaddr, true);
1032
1033         /* Set the HW DMA mode and the COE */
1034         stmmac_dma_operation_mode(priv);
1035
1036         /* Extra statistics */
1037         memset(&priv->xstats, 0, sizeof(struct stmmac_extra_stats));
1038         priv->xstats.threshold = tc;
1039
1040         stmmac_mmc_setup(priv);
1041
1042 #ifdef CONFIG_STMMAC_DEBUG_FS
1043         ret = stmmac_init_fs(dev);
1044         if (ret < 0)
1045                 pr_warning("%s: failed debugFS registration\n", __func__);
1046 #endif
1047         /* Start the ball rolling... */
1048         DBG(probe, DEBUG, "%s: DMA RX/TX processes started...\n", dev->name);
1049         priv->hw->dma->start_tx(priv->ioaddr);
1050         priv->hw->dma->start_rx(priv->ioaddr);
1051
1052 #ifdef CONFIG_STMMAC_TIMER
1053         priv->tm->timer_start(tmrate);
1054 #endif
1055
1056         /* Dump DMA/MAC registers */
1057         if (netif_msg_hw(priv)) {
1058                 priv->hw->mac->dump_regs(priv->ioaddr);
1059                 priv->hw->dma->dump_regs(priv->ioaddr);
1060         }
1061
1062         if (priv->phydev)
1063                 phy_start(priv->phydev);
1064
1065         napi_enable(&priv->napi);
1066         skb_queue_head_init(&priv->rx_recycle);
1067         netif_start_queue(dev);
1068
1069         return 0;
1070
1071 open_error_wolirq:
1072         free_irq(dev->irq, dev);
1073
1074 open_error:
1075 #ifdef CONFIG_STMMAC_TIMER
1076         kfree(priv->tm);
1077 #endif
1078         if (priv->phydev)
1079                 phy_disconnect(priv->phydev);
1080
1081         stmmac_clk_disable(priv);
1082
1083         return ret;
1084 }
1085
1086 /**
1087  *  stmmac_release - close entry point of the driver
1088  *  @dev : device pointer.
1089  *  Description:
1090  *  This is the stop entry point of the driver.
1091  */
1092 static int stmmac_release(struct net_device *dev)
1093 {
1094         struct stmmac_priv *priv = netdev_priv(dev);
1095
1096         /* Stop and disconnect the PHY */
1097         if (priv->phydev) {
1098                 phy_stop(priv->phydev);
1099                 phy_disconnect(priv->phydev);
1100                 priv->phydev = NULL;
1101         }
1102
1103         netif_stop_queue(dev);
1104
1105 #ifdef CONFIG_STMMAC_TIMER
1106         /* Stop and release the timer */
1107         stmmac_close_ext_timer();
1108         if (priv->tm != NULL)
1109                 kfree(priv->tm);
1110 #endif
1111         napi_disable(&priv->napi);
1112         skb_queue_purge(&priv->rx_recycle);
1113
1114         /* Free the IRQ lines */
1115         free_irq(dev->irq, dev);
1116         if (priv->wol_irq != dev->irq)
1117                 free_irq(priv->wol_irq, dev);
1118
1119         /* Stop TX/RX DMA and clear the descriptors */
1120         priv->hw->dma->stop_tx(priv->ioaddr);
1121         priv->hw->dma->stop_rx(priv->ioaddr);
1122
1123         /* Release and free the Rx/Tx resources */
1124         free_dma_desc_resources(priv);
1125
1126         /* Disable the MAC Rx/Tx */
1127         stmmac_set_mac(priv->ioaddr, false);
1128
1129         netif_carrier_off(dev);
1130
1131 #ifdef CONFIG_STMMAC_DEBUG_FS
1132         stmmac_exit_fs();
1133 #endif
1134         stmmac_clk_disable(priv);
1135
1136         return 0;
1137 }
1138
1139 /**
1140  *  stmmac_xmit:
1141  *  @skb : the socket buffer
1142  *  @dev : device pointer
1143  *  Description : Tx entry point of the driver.
1144  */
1145 static netdev_tx_t stmmac_xmit(struct sk_buff *skb, struct net_device *dev)
1146 {
1147         struct stmmac_priv *priv = netdev_priv(dev);
1148         unsigned int txsize = priv->dma_tx_size;
1149         unsigned int entry;
1150         int i, csum_insertion = 0;
1151         int nfrags = skb_shinfo(skb)->nr_frags;
1152         struct dma_desc *desc, *first;
1153         unsigned int nopaged_len = skb_headlen(skb);
1154
1155         if (unlikely(stmmac_tx_avail(priv) < nfrags + 1)) {
1156                 if (!netif_queue_stopped(dev)) {
1157                         netif_stop_queue(dev);
1158                         /* This is a hard error, log it. */
1159                         pr_err("%s: BUG! Tx Ring full when queue awake\n",
1160                                 __func__);
1161                 }
1162                 return NETDEV_TX_BUSY;
1163         }
1164
1165         spin_lock(&priv->tx_lock);
1166
1167         entry = priv->cur_tx % txsize;
1168
1169 #ifdef STMMAC_XMIT_DEBUG
1170         if ((skb->len > ETH_FRAME_LEN) || nfrags)
1171                 pr_info("stmmac xmit:\n"
1172                        "\tskb addr %p - len: %d - nopaged_len: %d\n"
1173                        "\tn_frags: %d - ip_summed: %d - %s gso\n",
1174                        skb, skb->len, nopaged_len, nfrags, skb->ip_summed,
1175                        !skb_is_gso(skb) ? "isn't" : "is");
1176 #endif
1177
1178         csum_insertion = (skb->ip_summed == CHECKSUM_PARTIAL);
1179
1180         desc = priv->dma_tx + entry;
1181         first = desc;
1182
1183 #ifdef STMMAC_XMIT_DEBUG
1184         if ((nfrags > 0) || (skb->len > ETH_FRAME_LEN))
1185                 pr_debug("stmmac xmit: skb len: %d, nopaged_len: %d,\n"
1186                        "\t\tn_frags: %d, ip_summed: %d\n",
1187                        skb->len, nopaged_len, nfrags, skb->ip_summed);
1188 #endif
1189         priv->tx_skbuff[entry] = skb;
1190
1191         if (priv->hw->ring->is_jumbo_frm(skb->len, priv->plat->enh_desc)) {
1192                 entry = priv->hw->ring->jumbo_frm(priv, skb, csum_insertion);
1193                 desc = priv->dma_tx + entry;
1194         } else {
1195                 desc->des2 = dma_map_single(priv->device, skb->data,
1196                                         nopaged_len, DMA_TO_DEVICE);
1197                 priv->hw->desc->prepare_tx_desc(desc, 1, nopaged_len,
1198                                                 csum_insertion);
1199         }
1200
1201         for (i = 0; i < nfrags; i++) {
1202                 const skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
1203                 int len = skb_frag_size(frag);
1204
1205                 entry = (++priv->cur_tx) % txsize;
1206                 desc = priv->dma_tx + entry;
1207
1208                 TX_DBG("\t[entry %d] segment len: %d\n", entry, len);
1209                 desc->des2 = skb_frag_dma_map(priv->device, frag, 0, len,
1210                                               DMA_TO_DEVICE);
1211                 priv->tx_skbuff[entry] = NULL;
1212                 priv->hw->desc->prepare_tx_desc(desc, 0, len, csum_insertion);
1213                 wmb();
1214                 priv->hw->desc->set_tx_owner(desc);
1215         }
1216
1217         /* Interrupt on completition only for the latest segment */
1218         priv->hw->desc->close_tx_desc(desc);
1219
1220 #ifdef CONFIG_STMMAC_TIMER
1221         /* Clean IC while using timer */
1222         if (likely(priv->tm->enable))
1223                 priv->hw->desc->clear_tx_ic(desc);
1224 #endif
1225
1226         wmb();
1227
1228         /* To avoid raise condition */
1229         priv->hw->desc->set_tx_owner(first);
1230
1231         priv->cur_tx++;
1232
1233 #ifdef STMMAC_XMIT_DEBUG
1234         if (netif_msg_pktdata(priv)) {
1235                 pr_info("stmmac xmit: current=%d, dirty=%d, entry=%d, "
1236                        "first=%p, nfrags=%d\n",
1237                        (priv->cur_tx % txsize), (priv->dirty_tx % txsize),
1238                        entry, first, nfrags);
1239                 display_ring(priv->dma_tx, txsize);
1240                 pr_info(">>> frame to be transmitted: ");
1241                 print_pkt(skb->data, skb->len);
1242         }
1243 #endif
1244         if (unlikely(stmmac_tx_avail(priv) <= (MAX_SKB_FRAGS + 1))) {
1245                 TX_DBG("%s: stop transmitted packets\n", __func__);
1246                 netif_stop_queue(dev);
1247         }
1248
1249         dev->stats.tx_bytes += skb->len;
1250
1251         skb_tx_timestamp(skb);
1252
1253         priv->hw->dma->enable_dma_transmission(priv->ioaddr);
1254
1255         spin_unlock(&priv->tx_lock);
1256
1257         return NETDEV_TX_OK;
1258 }
1259
1260 static inline void stmmac_rx_refill(struct stmmac_priv *priv)
1261 {
1262         unsigned int rxsize = priv->dma_rx_size;
1263         int bfsize = priv->dma_buf_sz;
1264         struct dma_desc *p = priv->dma_rx;
1265
1266         for (; priv->cur_rx - priv->dirty_rx > 0; priv->dirty_rx++) {
1267                 unsigned int entry = priv->dirty_rx % rxsize;
1268                 if (likely(priv->rx_skbuff[entry] == NULL)) {
1269                         struct sk_buff *skb;
1270
1271                         skb = __skb_dequeue(&priv->rx_recycle);
1272                         if (skb == NULL)
1273                                 skb = netdev_alloc_skb_ip_align(priv->dev,
1274                                                                 bfsize);
1275
1276                         if (unlikely(skb == NULL))
1277                                 break;
1278
1279                         priv->rx_skbuff[entry] = skb;
1280                         priv->rx_skbuff_dma[entry] =
1281                             dma_map_single(priv->device, skb->data, bfsize,
1282                                            DMA_FROM_DEVICE);
1283
1284                         (p + entry)->des2 = priv->rx_skbuff_dma[entry];
1285
1286                         if (unlikely(priv->plat->has_gmac))
1287                                 priv->hw->ring->refill_desc3(bfsize, p + entry);
1288
1289                         RX_DBG(KERN_INFO "\trefill entry #%d\n", entry);
1290                 }
1291                 wmb();
1292                 priv->hw->desc->set_rx_owner(p + entry);
1293         }
1294 }
1295
1296 static int stmmac_rx(struct stmmac_priv *priv, int limit)
1297 {
1298         unsigned int rxsize = priv->dma_rx_size;
1299         unsigned int entry = priv->cur_rx % rxsize;
1300         unsigned int next_entry;
1301         unsigned int count = 0;
1302         struct dma_desc *p = priv->dma_rx + entry;
1303         struct dma_desc *p_next;
1304
1305 #ifdef STMMAC_RX_DEBUG
1306         if (netif_msg_hw(priv)) {
1307                 pr_debug(">>> stmmac_rx: descriptor ring:\n");
1308                 display_ring(priv->dma_rx, rxsize);
1309         }
1310 #endif
1311         while (!priv->hw->desc->get_rx_owner(p)) {
1312                 int status;
1313
1314                 if (count >= limit)
1315                         break;
1316
1317                 count++;
1318
1319                 next_entry = (++priv->cur_rx) % rxsize;
1320                 p_next = priv->dma_rx + next_entry;
1321                 prefetch(p_next);
1322
1323                 /* read the status of the incoming frame */
1324                 status = (priv->hw->desc->rx_status(&priv->dev->stats,
1325                                                     &priv->xstats, p));
1326                 if (unlikely(status == discard_frame))
1327                         priv->dev->stats.rx_errors++;
1328                 else {
1329                         struct sk_buff *skb;
1330                         int frame_len;
1331
1332                         frame_len = priv->hw->desc->get_rx_frame_len(p,
1333                                         priv->plat->rx_coe);
1334                         /* ACS is set; GMAC core strips PAD/FCS for IEEE 802.3
1335                          * Type frames (LLC/LLC-SNAP) */
1336                         if (unlikely(status != llc_snap))
1337                                 frame_len -= ETH_FCS_LEN;
1338 #ifdef STMMAC_RX_DEBUG
1339                         if (frame_len > ETH_FRAME_LEN)
1340                                 pr_debug("\tRX frame size %d, COE status: %d\n",
1341                                         frame_len, status);
1342
1343                         if (netif_msg_hw(priv))
1344                                 pr_debug("\tdesc: %p [entry %d] buff=0x%x\n",
1345                                         p, entry, p->des2);
1346 #endif
1347                         skb = priv->rx_skbuff[entry];
1348                         if (unlikely(!skb)) {
1349                                 pr_err("%s: Inconsistent Rx descriptor chain\n",
1350                                         priv->dev->name);
1351                                 priv->dev->stats.rx_dropped++;
1352                                 break;
1353                         }
1354                         prefetch(skb->data - NET_IP_ALIGN);
1355                         priv->rx_skbuff[entry] = NULL;
1356
1357                         skb_put(skb, frame_len);
1358                         dma_unmap_single(priv->device,
1359                                          priv->rx_skbuff_dma[entry],
1360                                          priv->dma_buf_sz, DMA_FROM_DEVICE);
1361 #ifdef STMMAC_RX_DEBUG
1362                         if (netif_msg_pktdata(priv)) {
1363                                 pr_info(" frame received (%dbytes)", frame_len);
1364                                 print_pkt(skb->data, frame_len);
1365                         }
1366 #endif
1367                         skb->protocol = eth_type_trans(skb, priv->dev);
1368
1369                         if (unlikely(!priv->plat->rx_coe)) {
1370                                 /* No RX COE for old mac10/100 devices */
1371                                 skb_checksum_none_assert(skb);
1372                                 netif_receive_skb(skb);
1373                         } else {
1374                                 skb->ip_summed = CHECKSUM_UNNECESSARY;
1375                                 napi_gro_receive(&priv->napi, skb);
1376                         }
1377
1378                         priv->dev->stats.rx_packets++;
1379                         priv->dev->stats.rx_bytes += frame_len;
1380                 }
1381                 entry = next_entry;
1382                 p = p_next;     /* use prefetched values */
1383         }
1384
1385         stmmac_rx_refill(priv);
1386
1387         priv->xstats.rx_pkt_n += count;
1388
1389         return count;
1390 }
1391
1392 /**
1393  *  stmmac_poll - stmmac poll method (NAPI)
1394  *  @napi : pointer to the napi structure.
1395  *  @budget : maximum number of packets that the current CPU can receive from
1396  *            all interfaces.
1397  *  Description :
1398  *   This function implements the the reception process.
1399  *   Also it runs the TX completion thread
1400  */
1401 static int stmmac_poll(struct napi_struct *napi, int budget)
1402 {
1403         struct stmmac_priv *priv = container_of(napi, struct stmmac_priv, napi);
1404         int work_done = 0;
1405
1406         priv->xstats.poll_n++;
1407         stmmac_tx(priv);
1408         work_done = stmmac_rx(priv, budget);
1409
1410         if (work_done < budget) {
1411                 napi_complete(napi);
1412                 stmmac_enable_irq(priv);
1413         }
1414         return work_done;
1415 }
1416
1417 /**
1418  *  stmmac_tx_timeout
1419  *  @dev : Pointer to net device structure
1420  *  Description: this function is called when a packet transmission fails to
1421  *   complete within a reasonable tmrate. The driver will mark the error in the
1422  *   netdev structure and arrange for the device to be reset to a sane state
1423  *   in order to transmit a new packet.
1424  */
1425 static void stmmac_tx_timeout(struct net_device *dev)
1426 {
1427         struct stmmac_priv *priv = netdev_priv(dev);
1428
1429         /* Clear Tx resources and restart transmitting again */
1430         stmmac_tx_err(priv);
1431 }
1432
1433 /* Configuration changes (passed on by ifconfig) */
1434 static int stmmac_config(struct net_device *dev, struct ifmap *map)
1435 {
1436         if (dev->flags & IFF_UP)        /* can't act on a running interface */
1437                 return -EBUSY;
1438
1439         /* Don't allow changing the I/O address */
1440         if (map->base_addr != dev->base_addr) {
1441                 pr_warning("%s: can't change I/O address\n", dev->name);
1442                 return -EOPNOTSUPP;
1443         }
1444
1445         /* Don't allow changing the IRQ */
1446         if (map->irq != dev->irq) {
1447                 pr_warning("%s: can't change IRQ number %d\n",
1448                        dev->name, dev->irq);
1449                 return -EOPNOTSUPP;
1450         }
1451
1452         /* ignore other fields */
1453         return 0;
1454 }
1455
1456 /**
1457  *  stmmac_set_rx_mode - entry point for multicast addressing
1458  *  @dev : pointer to the device structure
1459  *  Description:
1460  *  This function is a driver entry point which gets called by the kernel
1461  *  whenever multicast addresses must be enabled/disabled.
1462  *  Return value:
1463  *  void.
1464  */
1465 static void stmmac_set_rx_mode(struct net_device *dev)
1466 {
1467         struct stmmac_priv *priv = netdev_priv(dev);
1468
1469         spin_lock(&priv->lock);
1470         priv->hw->mac->set_filter(dev, priv->synopsys_id);
1471         spin_unlock(&priv->lock);
1472 }
1473
1474 /**
1475  *  stmmac_change_mtu - entry point to change MTU size for the device.
1476  *  @dev : device pointer.
1477  *  @new_mtu : the new MTU size for the device.
1478  *  Description: the Maximum Transfer Unit (MTU) is used by the network layer
1479  *  to drive packet transmission. Ethernet has an MTU of 1500 octets
1480  *  (ETH_DATA_LEN). This value can be changed with ifconfig.
1481  *  Return value:
1482  *  0 on success and an appropriate (-)ve integer as defined in errno.h
1483  *  file on failure.
1484  */
1485 static int stmmac_change_mtu(struct net_device *dev, int new_mtu)
1486 {
1487         struct stmmac_priv *priv = netdev_priv(dev);
1488         int max_mtu;
1489
1490         if (netif_running(dev)) {
1491                 pr_err("%s: must be stopped to change its MTU\n", dev->name);
1492                 return -EBUSY;
1493         }
1494
1495         if (priv->plat->enh_desc)
1496                 max_mtu = JUMBO_LEN;
1497         else
1498                 max_mtu = SKB_MAX_HEAD(NET_SKB_PAD + NET_IP_ALIGN);
1499
1500         if ((new_mtu < 46) || (new_mtu > max_mtu)) {
1501                 pr_err("%s: invalid MTU, max MTU is: %d\n", dev->name, max_mtu);
1502                 return -EINVAL;
1503         }
1504
1505         dev->mtu = new_mtu;
1506         netdev_update_features(dev);
1507
1508         return 0;
1509 }
1510
1511 static netdev_features_t stmmac_fix_features(struct net_device *dev,
1512         netdev_features_t features)
1513 {
1514         struct stmmac_priv *priv = netdev_priv(dev);
1515
1516         if (priv->plat->rx_coe == STMMAC_RX_COE_NONE)
1517                 features &= ~NETIF_F_RXCSUM;
1518         else if (priv->plat->rx_coe == STMMAC_RX_COE_TYPE1)
1519                 features &= ~NETIF_F_IPV6_CSUM;
1520         if (!priv->plat->tx_coe)
1521                 features &= ~NETIF_F_ALL_CSUM;
1522
1523         /* Some GMAC devices have a bugged Jumbo frame support that
1524          * needs to have the Tx COE disabled for oversized frames
1525          * (due to limited buffer sizes). In this case we disable
1526          * the TX csum insertionin the TDES and not use SF. */
1527         if (priv->plat->bugged_jumbo && (dev->mtu > ETH_DATA_LEN))
1528                 features &= ~NETIF_F_ALL_CSUM;
1529
1530         return features;
1531 }
1532
1533 static irqreturn_t stmmac_interrupt(int irq, void *dev_id)
1534 {
1535         struct net_device *dev = (struct net_device *)dev_id;
1536         struct stmmac_priv *priv = netdev_priv(dev);
1537
1538         if (unlikely(!dev)) {
1539                 pr_err("%s: invalid dev pointer\n", __func__);
1540                 return IRQ_NONE;
1541         }
1542
1543         if (priv->plat->has_gmac)
1544                 /* To handle GMAC own interrupts */
1545                 priv->hw->mac->host_irq_status((void __iomem *) dev->base_addr);
1546
1547         stmmac_dma_interrupt(priv);
1548
1549         return IRQ_HANDLED;
1550 }
1551
1552 #ifdef CONFIG_NET_POLL_CONTROLLER
1553 /* Polling receive - used by NETCONSOLE and other diagnostic tools
1554  * to allow network I/O with interrupts disabled. */
1555 static void stmmac_poll_controller(struct net_device *dev)
1556 {
1557         disable_irq(dev->irq);
1558         stmmac_interrupt(dev->irq, dev);
1559         enable_irq(dev->irq);
1560 }
1561 #endif
1562
1563 /**
1564  *  stmmac_ioctl - Entry point for the Ioctl
1565  *  @dev: Device pointer.
1566  *  @rq: An IOCTL specefic structure, that can contain a pointer to
1567  *  a proprietary structure used to pass information to the driver.
1568  *  @cmd: IOCTL command
1569  *  Description:
1570  *  Currently there are no special functionality supported in IOCTL, just the
1571  *  phy_mii_ioctl(...) can be invoked.
1572  */
1573 static int stmmac_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
1574 {
1575         struct stmmac_priv *priv = netdev_priv(dev);
1576         int ret;
1577
1578         if (!netif_running(dev))
1579                 return -EINVAL;
1580
1581         if (!priv->phydev)
1582                 return -EINVAL;
1583
1584         ret = phy_mii_ioctl(priv->phydev, rq, cmd);
1585
1586         return ret;
1587 }
1588
1589 #ifdef CONFIG_STMMAC_DEBUG_FS
1590 static struct dentry *stmmac_fs_dir;
1591 static struct dentry *stmmac_rings_status;
1592 static struct dentry *stmmac_dma_cap;
1593
1594 static int stmmac_sysfs_ring_read(struct seq_file *seq, void *v)
1595 {
1596         struct tmp_s {
1597                 u64 a;
1598                 unsigned int b;
1599                 unsigned int c;
1600         };
1601         int i;
1602         struct net_device *dev = seq->private;
1603         struct stmmac_priv *priv = netdev_priv(dev);
1604
1605         seq_printf(seq, "=======================\n");
1606         seq_printf(seq, " RX descriptor ring\n");
1607         seq_printf(seq, "=======================\n");
1608
1609         for (i = 0; i < priv->dma_rx_size; i++) {
1610                 struct tmp_s *x = (struct tmp_s *)(priv->dma_rx + i);
1611                 seq_printf(seq, "[%d] DES0=0x%x DES1=0x%x BUF1=0x%x BUF2=0x%x",
1612                            i, (unsigned int)(x->a),
1613                            (unsigned int)((x->a) >> 32), x->b, x->c);
1614                 seq_printf(seq, "\n");
1615         }
1616
1617         seq_printf(seq, "\n");
1618         seq_printf(seq, "=======================\n");
1619         seq_printf(seq, "  TX descriptor ring\n");
1620         seq_printf(seq, "=======================\n");
1621
1622         for (i = 0; i < priv->dma_tx_size; i++) {
1623                 struct tmp_s *x = (struct tmp_s *)(priv->dma_tx + i);
1624                 seq_printf(seq, "[%d] DES0=0x%x DES1=0x%x BUF1=0x%x BUF2=0x%x",
1625                            i, (unsigned int)(x->a),
1626                            (unsigned int)((x->a) >> 32), x->b, x->c);
1627                 seq_printf(seq, "\n");
1628         }
1629
1630         return 0;
1631 }
1632
1633 static int stmmac_sysfs_ring_open(struct inode *inode, struct file *file)
1634 {
1635         return single_open(file, stmmac_sysfs_ring_read, inode->i_private);
1636 }
1637
1638 static const struct file_operations stmmac_rings_status_fops = {
1639         .owner = THIS_MODULE,
1640         .open = stmmac_sysfs_ring_open,
1641         .read = seq_read,
1642         .llseek = seq_lseek,
1643         .release = single_release,
1644 };
1645
1646 static int stmmac_sysfs_dma_cap_read(struct seq_file *seq, void *v)
1647 {
1648         struct net_device *dev = seq->private;
1649         struct stmmac_priv *priv = netdev_priv(dev);
1650
1651         if (!priv->hw_cap_support) {
1652                 seq_printf(seq, "DMA HW features not supported\n");
1653                 return 0;
1654         }
1655
1656         seq_printf(seq, "==============================\n");
1657         seq_printf(seq, "\tDMA HW features\n");
1658         seq_printf(seq, "==============================\n");
1659
1660         seq_printf(seq, "\t10/100 Mbps %s\n",
1661                    (priv->dma_cap.mbps_10_100) ? "Y" : "N");
1662         seq_printf(seq, "\t1000 Mbps %s\n",
1663                    (priv->dma_cap.mbps_1000) ? "Y" : "N");
1664         seq_printf(seq, "\tHalf duple %s\n",
1665                    (priv->dma_cap.half_duplex) ? "Y" : "N");
1666         seq_printf(seq, "\tHash Filter: %s\n",
1667                    (priv->dma_cap.hash_filter) ? "Y" : "N");
1668         seq_printf(seq, "\tMultiple MAC address registers: %s\n",
1669                    (priv->dma_cap.multi_addr) ? "Y" : "N");
1670         seq_printf(seq, "\tPCS (TBI/SGMII/RTBI PHY interfatces): %s\n",
1671                    (priv->dma_cap.pcs) ? "Y" : "N");
1672         seq_printf(seq, "\tSMA (MDIO) Interface: %s\n",
1673                    (priv->dma_cap.sma_mdio) ? "Y" : "N");
1674         seq_printf(seq, "\tPMT Remote wake up: %s\n",
1675                    (priv->dma_cap.pmt_remote_wake_up) ? "Y" : "N");
1676         seq_printf(seq, "\tPMT Magic Frame: %s\n",
1677                    (priv->dma_cap.pmt_magic_frame) ? "Y" : "N");
1678         seq_printf(seq, "\tRMON module: %s\n",
1679                    (priv->dma_cap.rmon) ? "Y" : "N");
1680         seq_printf(seq, "\tIEEE 1588-2002 Time Stamp: %s\n",
1681                    (priv->dma_cap.time_stamp) ? "Y" : "N");
1682         seq_printf(seq, "\tIEEE 1588-2008 Advanced Time Stamp:%s\n",
1683                    (priv->dma_cap.atime_stamp) ? "Y" : "N");
1684         seq_printf(seq, "\t802.3az - Energy-Efficient Ethernet (EEE) %s\n",
1685                    (priv->dma_cap.eee) ? "Y" : "N");
1686         seq_printf(seq, "\tAV features: %s\n", (priv->dma_cap.av) ? "Y" : "N");
1687         seq_printf(seq, "\tChecksum Offload in TX: %s\n",
1688                    (priv->dma_cap.tx_coe) ? "Y" : "N");
1689         seq_printf(seq, "\tIP Checksum Offload (type1) in RX: %s\n",
1690                    (priv->dma_cap.rx_coe_type1) ? "Y" : "N");
1691         seq_printf(seq, "\tIP Checksum Offload (type2) in RX: %s\n",
1692                    (priv->dma_cap.rx_coe_type2) ? "Y" : "N");
1693         seq_printf(seq, "\tRXFIFO > 2048bytes: %s\n",
1694                    (priv->dma_cap.rxfifo_over_2048) ? "Y" : "N");
1695         seq_printf(seq, "\tNumber of Additional RX channel: %d\n",
1696                    priv->dma_cap.number_rx_channel);
1697         seq_printf(seq, "\tNumber of Additional TX channel: %d\n",
1698                    priv->dma_cap.number_tx_channel);
1699         seq_printf(seq, "\tEnhanced descriptors: %s\n",
1700                    (priv->dma_cap.enh_desc) ? "Y" : "N");
1701
1702         return 0;
1703 }
1704
1705 static int stmmac_sysfs_dma_cap_open(struct inode *inode, struct file *file)
1706 {
1707         return single_open(file, stmmac_sysfs_dma_cap_read, inode->i_private);
1708 }
1709
1710 static const struct file_operations stmmac_dma_cap_fops = {
1711         .owner = THIS_MODULE,
1712         .open = stmmac_sysfs_dma_cap_open,
1713         .read = seq_read,
1714         .llseek = seq_lseek,
1715         .release = single_release,
1716 };
1717
1718 static int stmmac_init_fs(struct net_device *dev)
1719 {
1720         /* Create debugfs entries */
1721         stmmac_fs_dir = debugfs_create_dir(STMMAC_RESOURCE_NAME, NULL);
1722
1723         if (!stmmac_fs_dir || IS_ERR(stmmac_fs_dir)) {
1724                 pr_err("ERROR %s, debugfs create directory failed\n",
1725                        STMMAC_RESOURCE_NAME);
1726
1727                 return -ENOMEM;
1728         }
1729
1730         /* Entry to report DMA RX/TX rings */
1731         stmmac_rings_status = debugfs_create_file("descriptors_status",
1732                                            S_IRUGO, stmmac_fs_dir, dev,
1733                                            &stmmac_rings_status_fops);
1734
1735         if (!stmmac_rings_status || IS_ERR(stmmac_rings_status)) {
1736                 pr_info("ERROR creating stmmac ring debugfs file\n");
1737                 debugfs_remove(stmmac_fs_dir);
1738
1739                 return -ENOMEM;
1740         }
1741
1742         /* Entry to report the DMA HW features */
1743         stmmac_dma_cap = debugfs_create_file("dma_cap", S_IRUGO, stmmac_fs_dir,
1744                                              dev, &stmmac_dma_cap_fops);
1745
1746         if (!stmmac_dma_cap || IS_ERR(stmmac_dma_cap)) {
1747                 pr_info("ERROR creating stmmac MMC debugfs file\n");
1748                 debugfs_remove(stmmac_rings_status);
1749                 debugfs_remove(stmmac_fs_dir);
1750
1751                 return -ENOMEM;
1752         }
1753
1754         return 0;
1755 }
1756
1757 static void stmmac_exit_fs(void)
1758 {
1759         debugfs_remove(stmmac_rings_status);
1760         debugfs_remove(stmmac_dma_cap);
1761         debugfs_remove(stmmac_fs_dir);
1762 }
1763 #endif /* CONFIG_STMMAC_DEBUG_FS */
1764
1765 static const struct net_device_ops stmmac_netdev_ops = {
1766         .ndo_open = stmmac_open,
1767         .ndo_start_xmit = stmmac_xmit,
1768         .ndo_stop = stmmac_release,
1769         .ndo_change_mtu = stmmac_change_mtu,
1770         .ndo_fix_features = stmmac_fix_features,
1771         .ndo_set_rx_mode = stmmac_set_rx_mode,
1772         .ndo_tx_timeout = stmmac_tx_timeout,
1773         .ndo_do_ioctl = stmmac_ioctl,
1774         .ndo_set_config = stmmac_config,
1775 #ifdef CONFIG_NET_POLL_CONTROLLER
1776         .ndo_poll_controller = stmmac_poll_controller,
1777 #endif
1778         .ndo_set_mac_address = eth_mac_addr,
1779 };
1780
1781 /**
1782  *  stmmac_hw_init - Init the MAC device
1783  *  @priv : pointer to the private device structure.
1784  *  Description: this function detects which MAC device
1785  *  (GMAC/MAC10-100) has to attached, checks the HW capability
1786  *  (if supported) and sets the driver's features (for example
1787  *  to use the ring or chaine mode or support the normal/enh
1788  *  descriptor structure).
1789  */
1790 static int stmmac_hw_init(struct stmmac_priv *priv)
1791 {
1792         int ret = 0;
1793         struct mac_device_info *mac;
1794
1795         /* Identify the MAC HW device */
1796         if (priv->plat->has_gmac) {
1797                 priv->dev->priv_flags |= IFF_UNICAST_FLT;
1798                 mac = dwmac1000_setup(priv->ioaddr);
1799         } else {
1800                 mac = dwmac100_setup(priv->ioaddr);
1801         }
1802         if (!mac)
1803                 return -ENOMEM;
1804
1805         priv->hw = mac;
1806
1807         /* To use the chained or ring mode */
1808         priv->hw->ring = &ring_mode_ops;
1809
1810         /* Get and dump the chip ID */
1811         priv->synopsys_id = stmmac_get_synopsys_id(priv);
1812
1813         /* Get the HW capability (new GMAC newer than 3.50a) */
1814         priv->hw_cap_support = stmmac_get_hw_features(priv);
1815         if (priv->hw_cap_support) {
1816                 pr_info(" DMA HW capability register supported");
1817
1818                 /* We can override some gmac/dma configuration fields: e.g.
1819                  * enh_desc, tx_coe (e.g. that are passed through the
1820                  * platform) with the values from the HW capability
1821                  * register (if supported).
1822                  */
1823                 priv->plat->enh_desc = priv->dma_cap.enh_desc;
1824                 priv->plat->pmt = priv->dma_cap.pmt_remote_wake_up;
1825
1826                 priv->plat->tx_coe = priv->dma_cap.tx_coe;
1827
1828                 if (priv->dma_cap.rx_coe_type2)
1829                         priv->plat->rx_coe = STMMAC_RX_COE_TYPE2;
1830                 else if (priv->dma_cap.rx_coe_type1)
1831                         priv->plat->rx_coe = STMMAC_RX_COE_TYPE1;
1832
1833         } else
1834                 pr_info(" No HW DMA feature register supported");
1835
1836         /* Select the enhnaced/normal descriptor structures */
1837         stmmac_selec_desc_mode(priv);
1838
1839         /* Enable the IPC (Checksum Offload) and check if the feature has been
1840          * enabled during the core configuration. */
1841         ret = priv->hw->mac->rx_ipc(priv->ioaddr);
1842         if (!ret) {
1843                 pr_warning(" RX IPC Checksum Offload not configured.\n");
1844                 priv->plat->rx_coe = STMMAC_RX_COE_NONE;
1845         }
1846
1847         if (priv->plat->rx_coe)
1848                 pr_info(" RX Checksum Offload Engine supported (type %d)\n",
1849                         priv->plat->rx_coe);
1850         if (priv->plat->tx_coe)
1851                 pr_info(" TX Checksum insertion supported\n");
1852
1853         if (priv->plat->pmt) {
1854                 pr_info(" Wake-Up On Lan supported\n");
1855                 device_set_wakeup_capable(priv->device, 1);
1856         }
1857
1858         return ret;
1859 }
1860
1861 /**
1862  * stmmac_dvr_probe
1863  * @device: device pointer
1864  * @plat_dat: platform data pointer
1865  * @addr: iobase memory address
1866  * Description: this is the main probe function used to
1867  * call the alloc_etherdev, allocate the priv structure.
1868  */
1869 struct stmmac_priv *stmmac_dvr_probe(struct device *device,
1870                                      struct plat_stmmacenet_data *plat_dat,
1871                                      void __iomem *addr)
1872 {
1873         int ret = 0;
1874         struct net_device *ndev = NULL;
1875         struct stmmac_priv *priv;
1876
1877         ndev = alloc_etherdev(sizeof(struct stmmac_priv));
1878         if (!ndev)
1879                 return NULL;
1880
1881         SET_NETDEV_DEV(ndev, device);
1882
1883         priv = netdev_priv(ndev);
1884         priv->device = device;
1885         priv->dev = ndev;
1886
1887         ether_setup(ndev);
1888
1889         stmmac_set_ethtool_ops(ndev);
1890         priv->pause = pause;
1891         priv->plat = plat_dat;
1892         priv->ioaddr = addr;
1893         priv->dev->base_addr = (unsigned long)addr;
1894
1895         /* Verify driver arguments */
1896         stmmac_verify_args();
1897
1898         /* Override with kernel parameters if supplied XXX CRS XXX
1899          * this needs to have multiple instances */
1900         if ((phyaddr >= 0) && (phyaddr <= 31))
1901                 priv->plat->phy_addr = phyaddr;
1902
1903         /* Init MAC and get the capabilities */
1904         stmmac_hw_init(priv);
1905
1906         ndev->netdev_ops = &stmmac_netdev_ops;
1907
1908         ndev->hw_features = NETIF_F_SG | NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM |
1909                             NETIF_F_RXCSUM;
1910         ndev->features |= ndev->hw_features | NETIF_F_HIGHDMA;
1911         ndev->watchdog_timeo = msecs_to_jiffies(watchdog);
1912 #ifdef STMMAC_VLAN_TAG_USED
1913         /* Both mac100 and gmac support receive VLAN tag detection */
1914         ndev->features |= NETIF_F_HW_VLAN_RX;
1915 #endif
1916         priv->msg_enable = netif_msg_init(debug, default_msg_level);
1917
1918         if (flow_ctrl)
1919                 priv->flow_ctrl = FLOW_AUTO;    /* RX/TX pause on */
1920
1921         netif_napi_add(ndev, &priv->napi, stmmac_poll, 64);
1922
1923         spin_lock_init(&priv->lock);
1924         spin_lock_init(&priv->tx_lock);
1925
1926         ret = register_netdev(ndev);
1927         if (ret) {
1928                 pr_err("%s: ERROR %i registering the device\n", __func__, ret);
1929                 goto error;
1930         }
1931
1932         if (stmmac_clk_get(priv))
1933                 pr_warning("%s: warning: cannot get CSR clock\n", __func__);
1934
1935         /* If a specific clk_csr value is passed from the platform
1936          * this means that the CSR Clock Range selection cannot be
1937          * changed at run-time and it is fixed. Viceversa the driver'll try to
1938          * set the MDC clock dynamically according to the csr actual
1939          * clock input.
1940          */
1941         if (!priv->plat->clk_csr)
1942                 stmmac_clk_csr_set(priv);
1943         else
1944                 priv->clk_csr = priv->plat->clk_csr;
1945
1946         /* MDIO bus Registration */
1947         ret = stmmac_mdio_register(ndev);
1948         if (ret < 0) {
1949                 pr_debug("%s: MDIO bus (id: %d) registration failed",
1950                          __func__, priv->plat->bus_id);
1951                 goto error;
1952         }
1953
1954         return priv;
1955
1956 error:
1957         netif_napi_del(&priv->napi);
1958
1959         unregister_netdev(ndev);
1960         free_netdev(ndev);
1961
1962         return NULL;
1963 }
1964
1965 /**
1966  * stmmac_dvr_remove
1967  * @ndev: net device pointer
1968  * Description: this function resets the TX/RX processes, disables the MAC RX/TX
1969  * changes the link status, releases the DMA descriptor rings.
1970  */
1971 int stmmac_dvr_remove(struct net_device *ndev)
1972 {
1973         struct stmmac_priv *priv = netdev_priv(ndev);
1974
1975         pr_info("%s:\n\tremoving driver", __func__);
1976
1977         priv->hw->dma->stop_rx(priv->ioaddr);
1978         priv->hw->dma->stop_tx(priv->ioaddr);
1979
1980         stmmac_set_mac(priv->ioaddr, false);
1981         stmmac_mdio_unregister(ndev);
1982         netif_carrier_off(ndev);
1983         unregister_netdev(ndev);
1984         free_netdev(ndev);
1985
1986         return 0;
1987 }
1988
1989 #ifdef CONFIG_PM
1990 int stmmac_suspend(struct net_device *ndev)
1991 {
1992         struct stmmac_priv *priv = netdev_priv(ndev);
1993         int dis_ic = 0;
1994         unsigned long flags;
1995
1996         if (!ndev || !netif_running(ndev))
1997                 return 0;
1998
1999         if (priv->phydev)
2000                 phy_stop(priv->phydev);
2001
2002         spin_lock_irqsave(&priv->lock, flags);
2003
2004         netif_device_detach(ndev);
2005         netif_stop_queue(ndev);
2006
2007 #ifdef CONFIG_STMMAC_TIMER
2008         priv->tm->timer_stop();
2009         if (likely(priv->tm->enable))
2010                 dis_ic = 1;
2011 #endif
2012         napi_disable(&priv->napi);
2013
2014         /* Stop TX/RX DMA */
2015         priv->hw->dma->stop_tx(priv->ioaddr);
2016         priv->hw->dma->stop_rx(priv->ioaddr);
2017         /* Clear the Rx/Tx descriptors */
2018         priv->hw->desc->init_rx_desc(priv->dma_rx, priv->dma_rx_size,
2019                                      dis_ic);
2020         priv->hw->desc->init_tx_desc(priv->dma_tx, priv->dma_tx_size);
2021
2022         /* Enable Power down mode by programming the PMT regs */
2023         if (device_may_wakeup(priv->device))
2024                 priv->hw->mac->pmt(priv->ioaddr, priv->wolopts);
2025         else {
2026                 stmmac_set_mac(priv->ioaddr, false);
2027                 /* Disable clock in case of PWM is off */
2028                 stmmac_clk_disable(priv);
2029         }
2030         spin_unlock_irqrestore(&priv->lock, flags);
2031         return 0;
2032 }
2033
2034 int stmmac_resume(struct net_device *ndev)
2035 {
2036         struct stmmac_priv *priv = netdev_priv(ndev);
2037         unsigned long flags;
2038
2039         if (!netif_running(ndev))
2040                 return 0;
2041
2042         spin_lock_irqsave(&priv->lock, flags);
2043
2044         /* Power Down bit, into the PM register, is cleared
2045          * automatically as soon as a magic packet or a Wake-up frame
2046          * is received. Anyway, it's better to manually clear
2047          * this bit because it can generate problems while resuming
2048          * from another devices (e.g. serial console). */
2049         if (device_may_wakeup(priv->device))
2050                 priv->hw->mac->pmt(priv->ioaddr, 0);
2051         else
2052                 /* enable the clk prevously disabled */
2053                 stmmac_clk_enable(priv);
2054
2055         netif_device_attach(ndev);
2056
2057         /* Enable the MAC and DMA */
2058         stmmac_set_mac(priv->ioaddr, true);
2059         priv->hw->dma->start_tx(priv->ioaddr);
2060         priv->hw->dma->start_rx(priv->ioaddr);
2061
2062 #ifdef CONFIG_STMMAC_TIMER
2063         if (likely(priv->tm->enable))
2064                 priv->tm->timer_start(tmrate);
2065 #endif
2066         napi_enable(&priv->napi);
2067
2068         netif_start_queue(ndev);
2069
2070         spin_unlock_irqrestore(&priv->lock, flags);
2071
2072         if (priv->phydev)
2073                 phy_start(priv->phydev);
2074
2075         return 0;
2076 }
2077
2078 int stmmac_freeze(struct net_device *ndev)
2079 {
2080         if (!ndev || !netif_running(ndev))
2081                 return 0;
2082
2083         return stmmac_release(ndev);
2084 }
2085
2086 int stmmac_restore(struct net_device *ndev)
2087 {
2088         if (!ndev || !netif_running(ndev))
2089                 return 0;
2090
2091         return stmmac_open(ndev);
2092 }
2093 #endif /* CONFIG_PM */
2094
2095 /* Driver can be configured w/ and w/ both PCI and Platf drivers
2096  * depending on the configuration selected.
2097  */
2098 static int __init stmmac_init(void)
2099 {
2100         int err_plt = 0;
2101         int err_pci = 0;
2102
2103         err_plt = stmmac_register_platform();
2104         err_pci = stmmac_register_pci();
2105
2106         if ((err_pci) && (err_plt)) {
2107                 pr_err("stmmac: driver registration failed\n");
2108                 return -EINVAL;
2109         }
2110
2111         return 0;
2112 }
2113
2114 static void __exit stmmac_exit(void)
2115 {
2116         stmmac_unregister_platform();
2117         stmmac_unregister_pci();
2118 }
2119
2120 module_init(stmmac_init);
2121 module_exit(stmmac_exit);
2122
2123 #ifndef MODULE
2124 static int __init stmmac_cmdline_opt(char *str)
2125 {
2126         char *opt;
2127
2128         if (!str || !*str)
2129                 return -EINVAL;
2130         while ((opt = strsep(&str, ",")) != NULL) {
2131                 if (!strncmp(opt, "debug:", 6)) {
2132                         if (kstrtoint(opt + 6, 0, &debug))
2133                                 goto err;
2134                 } else if (!strncmp(opt, "phyaddr:", 8)) {
2135                         if (kstrtoint(opt + 8, 0, &phyaddr))
2136                                 goto err;
2137                 } else if (!strncmp(opt, "dma_txsize:", 11)) {
2138                         if (kstrtoint(opt + 11, 0, &dma_txsize))
2139                                 goto err;
2140                 } else if (!strncmp(opt, "dma_rxsize:", 11)) {
2141                         if (kstrtoint(opt + 11, 0, &dma_rxsize))
2142                                 goto err;
2143                 } else if (!strncmp(opt, "buf_sz:", 7)) {
2144                         if (kstrtoint(opt + 7, 0, &buf_sz))
2145                                 goto err;
2146                 } else if (!strncmp(opt, "tc:", 3)) {
2147                         if (kstrtoint(opt + 3, 0, &tc))
2148                                 goto err;
2149                 } else if (!strncmp(opt, "watchdog:", 9)) {
2150                         if (kstrtoint(opt + 9, 0, &watchdog))
2151                                 goto err;
2152                 } else if (!strncmp(opt, "flow_ctrl:", 10)) {
2153                         if (kstrtoint(opt + 10, 0, &flow_ctrl))
2154                                 goto err;
2155                 } else if (!strncmp(opt, "pause:", 6)) {
2156                         if (kstrtoint(opt + 6, 0, &pause))
2157                                 goto err;
2158 #ifdef CONFIG_STMMAC_TIMER
2159                 } else if (!strncmp(opt, "tmrate:", 7)) {
2160                         if (kstrtoint(opt + 7, 0, &tmrate))
2161                                 goto err;
2162 #endif
2163                 }
2164         }
2165         return 0;
2166
2167 err:
2168         pr_err("%s: ERROR broken module parameter conversion", __func__);
2169         return -EINVAL;
2170 }
2171
2172 __setup("stmmaceth=", stmmac_cmdline_opt);
2173 #endif
2174
2175 MODULE_DESCRIPTION("STMMAC 10/100/1000 Ethernet device driver");
2176 MODULE_AUTHOR("Giuseppe Cavallaro <peppe.cavallaro@st.com>");
2177 MODULE_LICENSE("GPL");