http://openvswitch.org/mlists/
-### Q: Why can I no longer connect to my OpenFlow controller or OVSDB
-manager?
+### Q: Why can I no longer connect to my OpenFlow controller or OVSDB manager?
A: Starting in OVS 2.4, we switched the default ports to the
IANA-specified port numbers for OpenFlow (6633->6653) and OVSDB
| 2.0.x | 2.6.32 to 3.10
| 2.1.x | 2.6.32 to 3.11
| 2.3.x | 2.6.32 to 3.14
-| 2.4.x | 2.6.32 to 3.19
+| 2.4.x | 2.6.32 to 4.0
+| 2.5.x | 2.6.32 to 4.2
Open vSwitch userspace should also work with the Linux kernel module
built into Linux 3.3 and later.
SPAN, see "How do I configure a port as a SPAN port, that is,
enable mirroring of all traffic to that port?"
+### Q: How do I configure a DPDK port as an access port?
+
+A: Firstly, you must have a DPDK-enabled version of Open vSwitch.
+
+ If your version is DPDK-enabled it will support the --dpdk
+ argument on the command line and will display lines with
+ "EAL:..." during startup when --dpdk is supplied.
+
+ Secondly, when adding a DPDK port, unlike a system port, the
+ type for the interface must be specified. For example;
+
+ ovs-vsctl add-br br0
+ ovs-vsctl add-port br0 dpdk0 -- set Interface dpdk0 type=dpdk
+
+ Finally, it is required that DPDK port names begin with 'dpdk'.
+
+ See [INSTALL.DPDK.md] for more information on enabling and using DPDK with
+ Open vSwitch.
+
### Q: How do I configure a VLAN as an RSPAN VLAN, that is, enable mirroring of all traffic to that VLAN?
A: The following commands configure br0 with eth0 as a trunk port and
documentation on the Port table in ovs-vswitchd.conf.db(5)
for all the details.
+ Configuration for DPDK-enabled interfaces is slightly less
+ straightforward: see [INSTALL.DPDK.md].
+
- Perhaps you don't actually need eth0 and eth1 to be on the
same bridge. For example, if you simply want to be able to
connect each of them to virtual machines, then you can put
Quality of Service (QoS)
------------------------
-### Q: How do I configure Quality of Service (QoS)?
+### Q: Does OVS support Quality of Service (QoS)?
+
+A: Yes. For traffic that egresses from a switch, OVS supports traffic
+ shaping; for traffic that ingresses into a switch, OVS support
+ policing. Policing is a simple form of quality-of-service that
+ simply drops packets received in excess of the configured rate. Due
+ to its simplicity, policing is usually less accurate and less
+ effective than egress traffic shaping, which queues packets.
+
+ Keep in mind that ingress and egress are from the perspective of the
+ switch. That means that egress shaping limits the rate at which
+ traffic is allowed to transmit from a physical interface, but the
+ rate at which traffic will be received on a virtual machine's VIF.
+ For ingress policing, the behavior is the opposite.
+
+### Q: How do I configure egress traffic shaping?
A: Suppose that you want to set up bridge br0 connected to physical
Ethernet port eth0 (a 1 Gbps device) and virtual machine interfaces
--all option), then you will have to destroy QoS and Queue records
individually.
+### Q: How do I configure ingress policing?
+
+A: A policing policy can be configured on an interface to drop packets
+ that arrive at a higher rate than the configured value. For example,
+ the following commands will rate-limit traffic that vif1.0 may
+ generate to 10Mbps:
+
+ ovs-vsctl set interface vif1.0 ingress_policing_rate=10000
+ ovs-vsctl set interface vif1.0 ingress_policing_burst=1000
+
+ Traffic policing can interact poorly with some network protocols and
+ can have surprising results. The "Ingress Policing" section of
+ ovs-vswitchd.conf.db(5) discusses the issues in greater detail.
+
### Q: I configured Quality of Service (QoS) in my OpenFlow network by
adding records to the QoS and Queue table, but the results aren't
what I expect.
[OPENFLOW-1.1+.md] in the Open vSwitch source tree tracks support for
OpenFlow 1.1 and later features. When support for OpenFlow 1.4 and
1.5 is solidly implemented, Open vSwitch will enable those version
- by default. Also, the OpenFlow 1.5 specification is still under
- development and thus subject to change.
+ by default.
### Q: Does Open vSwitch support MPLS?
that's correct, then trace the path of the response packet back to
the origin.
+ The open source tool called "plotnetcfg" can help to understand the
+ relationship between the networking devices on a single host.
+
Usually a simple ICMP echo request and reply ("ping") packet is
good enough. Start by initiating an ongoing "ping" from the origin
host to a remote host. If you are tracking down a connectivity
[WHY-OVS.md]:WHY-OVS.md
[INSTALL.md]:INSTALL.md
[OPENFLOW-1.1+.md]:OPENFLOW-1.1+.md
+[INSTALL.DPDK.md]:INSTALL.DPDK.md
projects / cascardo / ovs.git / blobdiff