select HAVE_IRQ_TIME_ACCOUNTING
select GENERIC_TIME_VSYSCALL
select ARCH_CLOCKSOURCE_DATA
+ select HANDLE_DOMAIN_IRQ
menu "Machine selection"
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_MIPS16
- select SYS_SUPPORTS_ZBOOT
+ select SYS_SUPPORTS_ZBOOT_UART_PROM
select USE_OF
help
Support for the Atheros AR71XX/AR724X/AR913X SoCs.
select CSRC_R4K
select SYNC_R4K
select COMMON_CLK
+ select BCM6345_L1_IRQ
select BCM7038_L1_IRQ
select BCM7120_L2_IRQ
select BRCMSTB_L2_IRQ
select GPIOLIB
select LEDS_GPIO_REGISTER
select BCM47XX_NVRAM
+ select BCM47XX_SPROM
help
Support for BCM47XX based boards
select ARCH_REQUIRE_GPIOLIB
select SWAP_IO_SPACE
select BOOT_RAW
- select HAVE_MACH_CLKDEV
select CLKDEV_LOOKUP
select USE_OF
select PINCTRL
select SYS_SUPPORTS_MULTITHREADING
select SYS_SUPPORTS_SMARTMIPS
select SYS_SUPPORTS_ZBOOT
+ select SYS_SUPPORTS_RELOCATABLE
select USE_OF
select ZONE_DMA32 if 64BIT
select BUILTIN_DTB
select MIPS_MSC
select SYS_HAS_CPU_MIPS32_R1
select SYS_HAS_CPU_MIPS32_R2
+ select SYS_HAS_CPU_MIPS32_R6
select SYS_HAS_CPU_MIPS64_R1
select SYS_HAS_EARLY_PRINTK
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_SMARTMIPS
select SYS_SUPPORTS_MICROMIPS
select SYS_SUPPORTS_MIPS16
+ select SYS_SUPPORTS_RELOCATABLE
select USB_EHCI_BIG_ENDIAN_DESC
select USB_EHCI_BIG_ENDIAN_MMIO
select USE_OF
select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_SUPPORTS_MIPS16
select SYS_HAS_EARLY_PRINTK
- select HAVE_MACH_CLKDEV
select CLKDEV_LOOKUP
select ARCH_HAS_RESET_CONTROLLER
select RESET_CONTROLLER
config HOLES_IN_ZONE
bool
+config SYS_SUPPORTS_RELOCATABLE
+ bool
+ help
+ Selected if the platform supports relocating the kernel.
+ The platform must provide plat_get_fdt() if it selects CONFIG_USE_OF
+ to allow access to command line and entropy sources.
+
#
# Endianness selection. Sufficiently obscure so many users don't know what to
# answer,so we try hard to limit the available choices. Also the use of a
#
config HARDWARE_WATCHPOINTS
bool
- default y if CPU_MIPSR1 || CPU_MIPSR2
+ default y if CPU_MIPSR1 || CPU_MIPSR2 || CPU_MIPSR6
menu "Kernel type"
select CPU_MIPSR2_IRQ_VI
select CPU_MIPSR2_IRQ_EI
select SYNC_R4K
- select MIPS_GIC_IPI
select MIPS_MT
select SMP
select SMP_UP
config MIPS_CMP
bool "MIPS CMP framework support (DEPRECATED)"
depends on SYS_SUPPORTS_MIPS_CMP && !CPU_MIPSR6
- select MIPS_GIC_IPI
select SMP
select SYNC_R4K
select SYS_SUPPORTS_SMP
config MIPS_CPS
bool "MIPS Coherent Processing System support"
- depends on SYS_SUPPORTS_MIPS_CPS && !CPU_MIPSR6
+ depends on SYS_SUPPORTS_MIPS_CPS
select MIPS_CM
select MIPS_CPC
select MIPS_CPS_PM if HOTPLUG_CPU
- select MIPS_GIC_IPI
select SMP
select SYNC_R4K if (CEVT_R4K || CSRC_R4K)
select SYS_SUPPORTS_HOTPLUG_CPU
select MIPS_CPC
bool
-config MIPS_GIC_IPI
- bool
-
config MIPS_CM
bool
config SYS_SUPPORTS_NUMA
bool
+config RELOCATABLE
+ bool "Relocatable kernel"
+ depends on SYS_SUPPORTS_RELOCATABLE && (CPU_MIPS32_R2 || CPU_MIPS64_R2 || CPU_MIPS32_R6 || CPU_MIPS64_R6)
+ help
+ This builds a kernel image that retains relocation information
+ so it can be loaded someplace besides the default 1MB.
+ The relocations make the kernel binary about 15% larger,
+ but are discarded at runtime
+
+config RELOCATION_TABLE_SIZE
+ hex "Relocation table size"
+ depends on RELOCATABLE
+ range 0x0 0x01000000
+ default "0x00100000"
+ ---help---
+ A table of relocation data will be appended to the kernel binary
+ and parsed at boot to fix up the relocated kernel.
+
+ This option allows the amount of space reserved for the table to be
+ adjusted, although the default of 1Mb should be ok in most cases.
+
+ The build will fail and a valid size suggested if this is too small.
+
+ If unsure, leave at the default value.
+
config NODES_SHIFT
int
default "6"
source "drivers/pci/Kconfig"
-source "drivers/pci/pcie/Kconfig"
-
#
# ISA support is now enabled via select. Too many systems still have the one
# or other ISA chip on the board that users don't know about so don't expect
source "drivers/pcmcia/Kconfig"
-source "drivers/pci/hotplug/Kconfig"
-
config RAPIDIO
tristate "RapidIO support"
depends on PCI