module_param_named(ignore_hpa, ata_ignore_hpa, int, 0644);
MODULE_PARM_DESC(ignore_hpa, "Ignore HPA limit (0=keep BIOS limits, 1=ignore limits, using full disk)");
+static int libata_dma_mask = ATA_DMA_MASK_ATA|ATA_DMA_MASK_ATAPI|ATA_DMA_MASK_CFA;
+module_param_named(dma, libata_dma_mask, int, 0444);
+MODULE_PARM_DESC(dma, "DMA enable/disable (0x1==ATA, 0x2==ATAPI, 0x4==CF)");
+
static int ata_probe_timeout = ATA_TMOUT_INTERNAL / HZ;
module_param(ata_probe_timeout, int, 0444);
MODULE_PARM_DESC(ata_probe_timeout, "Set ATA probing timeout (seconds)");
-int libata_noacpi = 1;
+int libata_noacpi = 0;
module_param_named(noacpi, libata_noacpi, int, 0444);
-MODULE_PARM_DESC(noacpi, "Disables the use of ACPI in suspend/resume when set");
+MODULE_PARM_DESC(noacpi, "Disables the use of ACPI in probe/suspend/resume when set");
MODULE_AUTHOR("Jeff Garzik");
MODULE_DESCRIPTION("Library module for ATA devices");
* None.
*
* RETURNS:
- * Device type, %ATA_DEV_ATA, %ATA_DEV_ATAPI, or %ATA_DEV_UNKNOWN
- * the event of failure.
+ * Device type, %ATA_DEV_ATA, %ATA_DEV_ATAPI, %ATA_DEV_PMP or
+ * %ATA_DEV_UNKNOWN the event of failure.
*/
-
unsigned int ata_dev_classify(const struct ata_taskfile *tf)
{
/* Apple's open source Darwin code hints that some devices only
* put a proper signature into the LBA mid/high registers,
* So, we only check those. It's sufficient for uniqueness.
+ *
+ * ATA/ATAPI-7 (d1532v1r1: Feb. 19, 2003) specified separate
+ * signatures for ATA and ATAPI devices attached on SerialATA,
+ * 0x3c/0xc3 and 0x69/0x96 respectively. However, SerialATA
+ * spec has never mentioned about using different signatures
+ * for ATA/ATAPI devices. Then, Serial ATA II: Port
+ * Multiplier specification began to use 0x69/0x96 to identify
+ * port multpliers and 0x3c/0xc3 to identify SEMB device.
+ * ATA/ATAPI-7 dropped descriptions about 0x3c/0xc3 and
+ * 0x69/0x96 shortly and described them as reserved for
+ * SerialATA.
+ *
+ * We follow the current spec and consider that 0x69/0x96
+ * identifies a port multiplier and 0x3c/0xc3 a SEMB device.
*/
-
- if (((tf->lbam == 0) && (tf->lbah == 0)) ||
- ((tf->lbam == 0x3c) && (tf->lbah == 0xc3))) {
+ if ((tf->lbam == 0) && (tf->lbah == 0)) {
DPRINTK("found ATA device by sig\n");
return ATA_DEV_ATA;
}
- if (((tf->lbam == 0x14) && (tf->lbah == 0xeb)) ||
- ((tf->lbam == 0x69) && (tf->lbah == 0x96))) {
+ if ((tf->lbam == 0x14) && (tf->lbah == 0xeb)) {
DPRINTK("found ATAPI device by sig\n");
return ATA_DEV_ATAPI;
}
+ if ((tf->lbam == 0x69) && (tf->lbah == 0x96)) {
+ DPRINTK("found PMP device by sig\n");
+ return ATA_DEV_PMP;
+ }
+
+ if ((tf->lbam == 0x3c) && (tf->lbah == 0xc3)) {
+ printk("ata: SEMB device ignored\n");
+ return ATA_DEV_SEMB_UNSUP; /* not yet */
+ }
+
DPRINTK("unknown device\n");
return ATA_DEV_UNKNOWN;
}
tf.protocol |= ATA_PROT_NODATA;
tf.device |= ATA_LBA;
- err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0);
+ err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0);
if (err_mask) {
ata_dev_printk(dev, KERN_WARNING, "failed to read native "
"max address (err_mask=0x%x)\n", err_mask);
tf.lbam = (new_sectors >> 8) & 0xff;
tf.lbah = (new_sectors >> 16) & 0xff;
- err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0);
+ err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0);
if (err_mask) {
ata_dev_printk(dev, KERN_WARNING, "failed to set "
"max address (err_mask=0x%x)\n", err_mask);
* @dma_dir: Data tranfer direction of the command
* @sg: sg list for the data buffer of the command
* @n_elem: Number of sg entries
+ * @timeout: Timeout in msecs (0 for default)
*
* Executes libata internal command with timeout. @tf contains
* command on entry and result on return. Timeout and error
unsigned ata_exec_internal_sg(struct ata_device *dev,
struct ata_taskfile *tf, const u8 *cdb,
int dma_dir, struct scatterlist *sg,
- unsigned int n_elem)
+ unsigned int n_elem, unsigned long timeout)
{
struct ata_link *link = dev->link;
struct ata_port *ap = link->ap;
spin_unlock_irqrestore(ap->lock, flags);
- rc = wait_for_completion_timeout(&wait, ata_probe_timeout);
+ if (!timeout)
+ timeout = ata_probe_timeout * 1000 / HZ;
+
+ rc = wait_for_completion_timeout(&wait, msecs_to_jiffies(timeout));
ata_port_flush_task(ap);
* @dma_dir: Data tranfer direction of the command
* @buf: Data buffer of the command
* @buflen: Length of data buffer
+ * @timeout: Timeout in msecs (0 for default)
*
* Wrapper around ata_exec_internal_sg() which takes simple
* buffer instead of sg list.
*/
unsigned ata_exec_internal(struct ata_device *dev,
struct ata_taskfile *tf, const u8 *cdb,
- int dma_dir, void *buf, unsigned int buflen)
+ int dma_dir, void *buf, unsigned int buflen,
+ unsigned long timeout)
{
struct scatterlist *psg = NULL, sg;
unsigned int n_elem = 0;
n_elem++;
}
- return ata_exec_internal_sg(dev, tf, cdb, dma_dir, psg, n_elem);
+ return ata_exec_internal_sg(dev, tf, cdb, dma_dir, psg, n_elem,
+ timeout);
}
/**
tf.flags |= ATA_TFLAG_DEVICE;
tf.protocol = ATA_PROT_NODATA;
- return ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0);
+ return ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0);
}
/**
tf.flags |= ATA_TFLAG_POLLING;
err_mask = ata_exec_internal(dev, &tf, NULL, DMA_FROM_DEVICE,
- id, sizeof(id[0]) * ATA_ID_WORDS);
+ id, sizeof(id[0]) * ATA_ID_WORDS, 0);
if (err_mask) {
if (err_mask & AC_ERR_NODEV_HINT) {
DPRINTK("ata%u.%d: NODEV after polling detection\n",
tf.feature = SETFEATURES_SPINUP;
tf.protocol = ATA_PROT_NODATA;
tf.flags |= ATA_TFLAG_ISADDR | ATA_TFLAG_DEVICE;
- err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0);
+ err_mask = ata_exec_internal(dev, &tf, NULL,
+ DMA_NONE, NULL, 0, 0);
if (err_mask && id[2] != 0x738c) {
rc = -EIO;
reason = "SPINUP failed";
/* step 1: calculate xfer_mask */
ata_link_for_each_dev(dev, link) {
unsigned int pio_mask, dma_mask;
+ unsigned int mode_mask;
if (!ata_dev_enabled(dev))
continue;
+ mode_mask = ATA_DMA_MASK_ATA;
+ if (dev->class == ATA_DEV_ATAPI)
+ mode_mask = ATA_DMA_MASK_ATAPI;
+ else if (ata_id_is_cfa(dev->id))
+ mode_mask = ATA_DMA_MASK_CFA;
+
ata_dev_xfermask(dev);
pio_mask = ata_pack_xfermask(dev->pio_mask, 0, 0);
dma_mask = ata_pack_xfermask(0, dev->mwdma_mask, dev->udma_mask);
+
+ if (libata_dma_mask & mode_mask)
+ dma_mask = ata_pack_xfermask(0, dev->mwdma_mask, dev->udma_mask);
+ else
+ dma_mask = 0;
+
dev->pio_mode = ata_xfer_mask2mode(pio_mask);
dev->dma_mode = ata_xfer_mask2mode(dma_mask);
unsigned long deadline)
{
struct ata_ioports *ioaddr = &ap->ioaddr;
+ struct ata_device *dev;
+ int i = 0;
DPRINTK("ata%u: bus reset via SRST\n", ap->print_id);
udelay(20); /* FIXME: flush */
iowrite8(ap->ctl, ioaddr->ctl_addr);
+ /* If we issued an SRST then an ATA drive (not ATAPI)
+ * may have changed configuration and be in PIO0 timing. If
+ * we did a hard reset (or are coming from power on) this is
+ * true for ATA or ATAPI. Until we've set a suitable controller
+ * mode we should not touch the bus as we may be talking too fast.
+ */
+
+ ata_link_for_each_dev(dev, &ap->link)
+ dev->pio_mode = XFER_PIO_0;
+
+ /* If the controller has a pio mode setup function then use
+ it to set the chipset to rights. Don't touch the DMA setup
+ as that will be dealt with when revalidating */
+ if (ap->ops->set_piomode) {
+ ata_link_for_each_dev(dev, &ap->link)
+ if (devmask & (1 << i++))
+ ap->ops->set_piomode(ap, dev);
+ }
+
/* spec mandates ">= 2ms" before checking status.
* We wait 150ms, because that was the magic delay used for
* ATAPI devices in Hale Landis's ATADRVR, for the period of time
(link->flags & ATA_LFLAG_HRST_TO_RESUME))
ehc->i.action |= ATA_EH_HARDRESET;
+ /* Some PMPs don't work with only SRST, force hardreset if PMP
+ * is supported.
+ */
+ if (ap->flags & ATA_FLAG_PMP)
+ ehc->i.action |= ATA_EH_HARDRESET;
+
/* if we're about to do hardreset, nothing more to do */
if (ehc->i.action & ATA_EH_HARDRESET)
return 0;
/* wait a while before checking status, see SRST for more info */
msleep(150);
+ /* If PMP is supported, we have to do follow-up SRST. Note
+ * that some PMPs don't send D2H Reg FIS after hardreset at
+ * all if the first port is empty. Wait for it just for a
+ * second and request follow-up SRST.
+ */
+ if (ap->flags & ATA_FLAG_PMP) {
+ ata_wait_ready(ap, jiffies + HZ);
+ return -EAGAIN;
+ }
+
rc = ata_wait_ready(ap, deadline);
/* link occupied, -ENODEV too is an error */
if (rc) {
{ "IOMEGA ZIP 250 ATAPI", NULL, ATA_HORKAGE_NODMA }, /* temporary fix */
{ "IOMEGA ZIP 250 ATAPI Floppy",
NULL, ATA_HORKAGE_NODMA },
+ /* Odd clown on sil3726/4726 PMPs */
+ { "Config Disk", NULL, ATA_HORKAGE_NODMA |
+ ATA_HORKAGE_SKIP_PM },
/* Weird ATAPI devices */
{ "TORiSAN DVD-ROM DRD-N216", NULL, ATA_HORKAGE_MAX_SEC_128 },
{ "Maxtor 7V300F0", "VA111630", ATA_HORKAGE_NONCQ },
{ "HITACHI HDS7250SASUN500G*", NULL, ATA_HORKAGE_NONCQ },
{ "HITACHI HDS7225SBSUN250G*", NULL, ATA_HORKAGE_NONCQ },
+ { "ST380817AS", "3.42", ATA_HORKAGE_NONCQ },
/* Blacklist entries taken from Silicon Image 3124/3132
Windows driver .inf file - also several Linux problem reports */
/* Drives which do spurious command completion */
{ "HTS541680J9SA00", "SB2IC7EP", ATA_HORKAGE_NONCQ, },
{ "HTS541612J9SA00", "SBDIC7JP", ATA_HORKAGE_NONCQ, },
+ { "HDT722516DLA380", "V43OA96A", ATA_HORKAGE_NONCQ, },
{ "Hitachi HTS541616J9SA00", "SB4OC70P", ATA_HORKAGE_NONCQ, },
{ "WDC WD740ADFD-00NLR1", NULL, ATA_HORKAGE_NONCQ, },
{ "WDC WD3200AAJS-00RYA0", "12.01B01", ATA_HORKAGE_NONCQ, },
{ "FUJITSU MHV2080BH", "00840028", ATA_HORKAGE_NONCQ, },
{ "ST9120822AS", "3.CLF", ATA_HORKAGE_NONCQ, },
{ "ST9160821AS", "3.CLF", ATA_HORKAGE_NONCQ, },
+ { "ST9160821AS", "3.ALD", ATA_HORKAGE_NONCQ, },
+ { "ST9160821AS", "3.CCD", ATA_HORKAGE_NONCQ, },
{ "ST3160812AS", "3.ADJ", ATA_HORKAGE_NONCQ, },
{ "ST980813AS", "3.ADB", ATA_HORKAGE_NONCQ, },
{ "SAMSUNG HD401LJ", "ZZ100-15", ATA_HORKAGE_NONCQ, },
tf.protocol = ATA_PROT_NODATA;
tf.nsect = dev->xfer_mode;
- err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0);
+ err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0);
DPRINTK("EXIT, err_mask=%x\n", err_mask);
return err_mask;
tf.protocol = ATA_PROT_NODATA;
tf.nsect = SATA_AN;
- err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0);
+ err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0);
DPRINTK("EXIT, err_mask=%x\n", err_mask);
return err_mask;
tf.nsect = sectors;
tf.device |= (heads - 1) & 0x0f; /* max head = num. of heads - 1 */
- err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0);
+ err_mask = ata_exec_internal(dev, &tf, NULL, DMA_NONE, NULL, 0, 0);
/* A clean abort indicates an original or just out of spec drive
and we should continue as we issue the setup based on the
drive reported working geometry */
* @val: Place to store read value
*
* Read SCR register @reg of @link into *@val. This function is
- * guaranteed to succeed if the cable type of the port is SATA
- * and the port implements ->scr_read.
+ * guaranteed to succeed if @link is ap->link, the cable type of
+ * the port is SATA and the port implements ->scr_read.
*
* LOCKING:
- * None.
+ * None if @link is ap->link. Kernel thread context otherwise.
*
* RETURNS:
* 0 on success, negative errno on failure.
*/
int sata_scr_read(struct ata_link *link, int reg, u32 *val)
{
- struct ata_port *ap = link->ap;
+ if (ata_is_host_link(link)) {
+ struct ata_port *ap = link->ap;
- if (sata_scr_valid(link))
- return ap->ops->scr_read(ap, reg, val);
- return -EOPNOTSUPP;
+ if (sata_scr_valid(link))
+ return ap->ops->scr_read(ap, reg, val);
+ return -EOPNOTSUPP;
+ }
+
+ return sata_pmp_scr_read(link, reg, val);
}
/**
* @val: value to write
*
* Write @val to SCR register @reg of @link. This function is
- * guaranteed to succeed if the cable type of the port is SATA
- * and the port implements ->scr_read.
+ * guaranteed to succeed if @link is ap->link, the cable type of
+ * the port is SATA and the port implements ->scr_read.
*
* LOCKING:
- * None.
+ * None if @link is ap->link. Kernel thread context otherwise.
*
* RETURNS:
* 0 on success, negative errno on failure.
*/
int sata_scr_write(struct ata_link *link, int reg, u32 val)
{
- struct ata_port *ap = link->ap;
+ if (ata_is_host_link(link)) {
+ struct ata_port *ap = link->ap;
+
+ if (sata_scr_valid(link))
+ return ap->ops->scr_write(ap, reg, val);
+ return -EOPNOTSUPP;
+ }
- if (sata_scr_valid(link))
- return ap->ops->scr_write(ap, reg, val);
- return -EOPNOTSUPP;
+ return sata_pmp_scr_write(link, reg, val);
}
/**
* function performs flush after writing to the register.
*
* LOCKING:
- * None.
+ * None if @link is ap->link. Kernel thread context otherwise.
*
* RETURNS:
* 0 on success, negative errno on failure.
*/
int sata_scr_write_flush(struct ata_link *link, int reg, u32 val)
{
- struct ata_port *ap = link->ap;
- int rc;
+ if (ata_is_host_link(link)) {
+ struct ata_port *ap = link->ap;
+ int rc;
- if (sata_scr_valid(link)) {
- rc = ap->ops->scr_write(ap, reg, val);
- if (rc == 0)
- rc = ap->ops->scr_read(ap, reg, &val);
- return rc;
+ if (sata_scr_valid(link)) {
+ rc = ap->ops->scr_write(ap, reg, val);
+ if (rc == 0)
+ rc = ap->ops->scr_read(ap, reg, &val);
+ return rc;
+ }
+ return -EOPNOTSUPP;
}
- return -EOPNOTSUPP;
+
+ return sata_pmp_scr_write(link, reg, val);
}
/**
if (ap->scsi_host)
scsi_host_put(ap->scsi_host);
+ kfree(ap->pmp_link);
kfree(ap);
host->ports[i] = NULL;
}
xfer_mask = ata_pack_xfermask(ap->pio_mask, ap->mwdma_mask,
ap->udma_mask);
- if (!ata_port_is_dummy(ap))
+ if (!ata_port_is_dummy(ap)) {
ata_port_printk(ap, KERN_INFO,
"%cATA max %s %s\n",
(ap->flags & ATA_FLAG_SATA) ? 'S' : 'P',
ata_mode_string(xfer_mask),
ap->link.eh_info.desc);
- else
+ ata_ehi_clear_desc(&ap->link.eh_info);
+ } else
ata_port_printk(ap, KERN_INFO, "DUMMY\n");
}
*/
void ata_pci_remove_one(struct pci_dev *pdev)
{
- struct device *dev = pci_dev_to_dev(pdev);
+ struct device *dev = &pdev->dev;
struct ata_host *host = dev_get_drvdata(dev);
ata_host_detach(host);
EXPORT_SYMBOL_GPL(ata_pci_clear_simplex);
#endif /* CONFIG_PCI */
+EXPORT_SYMBOL_GPL(sata_pmp_qc_defer_cmd_switch);
+EXPORT_SYMBOL_GPL(sata_pmp_std_prereset);
+EXPORT_SYMBOL_GPL(sata_pmp_std_hardreset);
+EXPORT_SYMBOL_GPL(sata_pmp_std_postreset);
+EXPORT_SYMBOL_GPL(sata_pmp_do_eh);
+
EXPORT_SYMBOL_GPL(__ata_ehi_push_desc);
EXPORT_SYMBOL_GPL(ata_ehi_push_desc);
EXPORT_SYMBOL_GPL(ata_ehi_clear_desc);
projects / cascardo / linux.git / blobdiff