/*
+ * IDE DMA support (including IDE PCI BM-DMA).
+ *
* Copyright (C) 1995-1998 Mark Lord
* Copyright (C) 1999-2000 Andre Hedrick <andre@linux-ide.org>
* Copyright (C) 2004, 2007 Bartlomiej Zolnierkiewicz
*
* May be copied or modified under the terms of the GNU General Public License
+ *
+ * DMA is supported for all IDE devices (disk drives, cdroms, tapes, floppies).
*/
/*
*/
/*
- * This module provides support for the bus-master IDE DMA functions
- * of various PCI chipsets, including the Intel PIIX (i82371FB for
- * the 430 FX chipset), the PIIX3 (i82371SB for the 430 HX/VX and
- * 440 chipsets), and the PIIX4 (i82371AB for the 430 TX chipset)
- * ("PIIX" stands for "PCI ISA IDE Xcellerator").
- *
- * Pretty much the same code works for other IDE PCI bus-mastering chipsets.
- *
- * DMA is supported for all IDE devices (disk drives, cdroms, tapes, floppies).
- *
- * By default, DMA support is prepared for use, but is currently enabled only
- * for drives which already have DMA enabled (UltraDMA or mode 2 multi/single),
- * or which are recognized as "good" (see table below). Drives with only mode0
- * or mode1 (multi/single) DMA should also work with this chipset/driver
- * (eg. MC2112A) but are not enabled by default.
- *
- * Use "hdparm -i" to view modes supported by a given drive.
- *
- * The hdparm-3.5 (or later) utility can be used for manually enabling/disabling
- * DMA support, but must be (re-)compiled against this kernel version or later.
- *
- * To enable DMA, use "hdparm -d1 /dev/hd?" on a per-drive basis after booting.
- * If problems arise, ide.c will disable DMA operation after a few retries.
- * This error recovery mechanism works and has been extremely well exercised.
- *
- * IDE drives, depending on their vintage, may support several different modes
- * of DMA operation. The boot-time modes are indicated with a "*" in
- * the "hdparm -i" listing, and can be changed with *knowledgeable* use of
- * the "hdparm -X" feature. There is seldom a need to do this, as drives
- * normally power-up with their "best" PIO/DMA modes enabled.
- *
- * Testing has been done with a rather extensive number of drives,
- * with Quantum & Western Digital models generally outperforming the pack,
- * and Fujitsu & Conner (and some Seagate which are really Conner) drives
- * showing more lackluster throughput.
- *
- * Keep an eye on /var/adm/messages for "DMA disabled" messages.
- *
- * Some people have reported trouble with Intel Zappa motherboards.
- * This can be fixed by upgrading the AMI BIOS to version 1.00.04.BS0,
- * available from ftp://ftp.intel.com/pub/bios/10004bs0.exe
- * (thanks to Glen Morrell <glen@spin.Stanford.edu> for researching this).
- *
* Thanks to "Christopher J. Reimer" <reimer@doe.carleton.ca> for
* fixing the problem with the BIOS on some Acer motherboards.
*
*
* Most importantly, thanks to Robert Bringman <rob@mars.trion.com>
* for supplying a Promise UDMA board & WD UDMA drive for this work!
- *
- * And, yes, Intel Zappa boards really *do* use both PIIX IDE ports.
- *
- * ATA-66/100 and recovery functions, I forgot the rest......
- *
*/
#include <linux/module.h>
EXPORT_SYMBOL_GPL(ide_build_sglist);
-#ifdef CONFIG_BLK_DEV_IDEDMA_PCI
+#ifdef CONFIG_BLK_DEV_IDEDMA_SFF
/**
* ide_build_dmatable - build IDE DMA table
*
EXPORT_SYMBOL_GPL(ide_destroy_dmatable);
-#ifdef CONFIG_BLK_DEV_IDEDMA_PCI
+#ifdef CONFIG_BLK_DEV_IDEDMA_SFF
/**
* config_drive_for_dma - attempt to activate IDE DMA
* @drive: the drive to place in DMA mode
}
EXPORT_SYMBOL_GPL(ide_dma_host_set);
-#endif /* CONFIG_BLK_DEV_IDEDMA_PCI */
+#endif /* CONFIG_BLK_DEV_IDEDMA_SFF */
/**
* ide_dma_off_quietly - Generic DMA kill
drive->hwif->dma_host_set(drive, 1);
}
-#ifdef CONFIG_BLK_DEV_IDEDMA_PCI
+#ifdef CONFIG_BLK_DEV_IDEDMA_SFF
/**
* ide_dma_setup - begin a DMA phase
* @drive: target device
return 1;
if (!drive->waiting_for_dma)
printk(KERN_WARNING "%s: (%s) called while not waiting\n",
- drive->name, __FUNCTION__);
+ drive->name, __func__);
return 0;
}
#else
static inline int config_drive_for_dma(ide_drive_t *drive) { return 0; }
-#endif /* CONFIG_BLK_DEV_IDEDMA_PCI */
+#endif /* CONFIG_BLK_DEV_IDEDMA_SFF */
int __ide_dma_bad_drive (ide_drive_t *drive)
{
{
struct hd_driveid *id = drive->id;
ide_hwif_t *hwif = drive->hwif;
+ const struct ide_port_ops *port_ops = hwif->port_ops;
unsigned int mask = 0;
switch(base) {
if ((id->field_valid & 4) == 0)
break;
- if (hwif->udma_filter)
- mask = hwif->udma_filter(drive);
+ if (port_ops && port_ops->udma_filter)
+ mask = port_ops->udma_filter(drive);
else
mask = hwif->ultra_mask;
mask &= id->dma_ultra;
case XFER_MW_DMA_0:
if ((id->field_valid & 2) == 0)
break;
- if (hwif->mdma_filter)
- mask = hwif->mdma_filter(drive);
+ if (port_ops && port_ops->mdma_filter)
+ mask = port_ops->mdma_filter(drive);
else
mask = hwif->mwdma_mask;
mask &= id->dma_mword;
speed = ide_max_dma_mode(drive);
- if (!speed) {
- /* is this really correct/needed? */
- if ((hwif->host_flags & IDE_HFLAG_CY82C693) &&
- ide_dma_good_drive(drive))
- return 1;
- else
- return 0;
- }
-
- if (hwif->host_flags & IDE_HFLAG_NO_SET_MODE)
+ if (!speed)
return 0;
if (ide_set_dma_mode(drive, speed))
ide_dma_on(drive);
}
-#ifdef CONFIG_BLK_DEV_IDEDMA_PCI
+#ifdef CONFIG_BLK_DEV_IDEDMA_SFF
void ide_dma_lost_irq (ide_drive_t *drive)
{
printk("%s: DMA interrupt recovery\n", drive->name);
EXPORT_SYMBOL(ide_dma_timeout);
-static void ide_release_dma_engine(ide_hwif_t *hwif)
+void ide_release_dma_engine(ide_hwif_t *hwif)
{
if (hwif->dmatable_cpu) {
struct pci_dev *pdev = to_pci_dev(hwif->dev);
}
}
-static int ide_release_iomio_dma(ide_hwif_t *hwif)
-{
- release_region(hwif->dma_base, 8);
- if (hwif->extra_ports)
- release_region(hwif->extra_base, hwif->extra_ports);
- return 1;
-}
-
-/*
- * Needed for allowing full modular support of ide-driver
- */
-int ide_release_dma(ide_hwif_t *hwif)
-{
- ide_release_dma_engine(hwif);
-
- if (hwif->mmio)
- return 1;
- else
- return ide_release_iomio_dma(hwif);
-}
-
static int ide_allocate_dma_engine(ide_hwif_t *hwif)
{
struct pci_dev *pdev = to_pci_dev(hwif->dev);
return 0;
printk(KERN_ERR "%s: -- Error, unable to allocate DMA table.\n",
- hwif->cds->name);
+ hwif->name);
return 1;
}
-static int ide_mapped_mmio_dma(ide_hwif_t *hwif, unsigned long base)
-{
- printk(KERN_INFO " %s: MMIO-DMA ", hwif->name);
-
- return 0;
-}
-
-static int ide_iomio_dma(ide_hwif_t *hwif, unsigned long base)
-{
- printk(KERN_INFO " %s: BM-DMA at 0x%04lx-0x%04lx",
- hwif->name, base, base + 7);
-
- if (!request_region(base, 8, hwif->name)) {
- printk(" -- Error, ports in use.\n");
- return 1;
- }
-
- if (hwif->cds->extra) {
- hwif->extra_base = base + (hwif->channel ? 8 : 16);
-
- if (!hwif->mate || !hwif->mate->extra_ports) {
- if (!request_region(hwif->extra_base,
- hwif->cds->extra, hwif->cds->name)) {
- printk(" -- Error, extra ports in use.\n");
- release_region(base, 8);
- return 1;
- }
- hwif->extra_ports = hwif->cds->extra;
- }
- }
-
- return 0;
-}
-
-static int ide_dma_iobase(ide_hwif_t *hwif, unsigned long base)
-{
- if (hwif->mmio)
- return ide_mapped_mmio_dma(hwif, base);
-
- return ide_iomio_dma(hwif, base);
-}
-
void ide_setup_dma(ide_hwif_t *hwif, unsigned long base)
{
- u8 dma_stat;
+ if (hwif->mmio)
+ printk(KERN_INFO " %s: MMIO-DMA\n", hwif->name);
+ else
+ printk(KERN_INFO " %s: BM-DMA at 0x%04lx-0x%04lx\n",
+ hwif->name, base, base + 7);
- if (ide_dma_iobase(hwif, base))
- return;
+ hwif->extra_base = base + (hwif->channel ? 8 : 16);
if (ide_allocate_dma_engine(hwif)) {
- ide_release_dma(hwif);
+ ide_release_dma_engine(hwif);
return;
}
hwif->dma_timeout = &ide_dma_timeout;
if (!hwif->dma_lost_irq)
hwif->dma_lost_irq = &ide_dma_lost_irq;
-
- dma_stat = hwif->INB(hwif->dma_status);
- printk(KERN_CONT ", BIOS settings: %s:%s, %s:%s\n",
- hwif->drives[0].name, (dma_stat & 0x20) ? "DMA" : "PIO",
- hwif->drives[1].name, (dma_stat & 0x40) ? "DMA" : "PIO");
}
EXPORT_SYMBOL_GPL(ide_setup_dma);
-#endif /* CONFIG_BLK_DEV_IDEDMA_PCI */
+#endif /* CONFIG_BLK_DEV_IDEDMA_SFF */
projects / cascardo / linux.git / blobdiff