static bool dw_mci_reset(struct dw_mci *host);
static bool dw_mci_ctrl_reset(struct dw_mci *host, u32 reset);
+static int dw_mci_card_busy(struct mmc_host *mmc);
#if defined(CONFIG_DEBUG_FS)
static int dw_mci_req_show(struct seq_file *s, void *v)
return cmdr;
}
+static void dw_mci_wait_while_busy(struct dw_mci *host, u32 cmd_flags)
+{
+ unsigned long timeout = jiffies + msecs_to_jiffies(500);
+
+ /*
+ * Databook says that before issuing a new data transfer command
+ * we need to check to see if the card is busy. Data transfer commands
+ * all have SDMMC_CMD_PRV_DAT_WAIT set, so we'll key off that.
+ *
+ * ...also allow sending for SDMMC_CMD_VOLT_SWITCH where busy is
+ * expected.
+ */
+ if ((cmd_flags & SDMMC_CMD_PRV_DAT_WAIT) &&
+ !(cmd_flags & SDMMC_CMD_VOLT_SWITCH)) {
+ while (mci_readl(host, STATUS) & SDMMC_STATUS_BUSY) {
+ if (time_after(jiffies, timeout)) {
+ /* Command will fail; we'll pass error then */
+ dev_err(host->dev, "Busy; trying anyway\n");
+ break;
+ }
+ udelay(10);
+ }
+ }
+}
+
static void dw_mci_start_command(struct dw_mci *host,
struct mmc_command *cmd, u32 cmd_flags)
{
mci_writel(host, CMDARG, cmd->arg);
wmb();
+ dw_mci_wait_while_busy(host, cmd_flags);
mci_writel(host, CMD, cmd_flags | SDMMC_CMD_START);
}
return;
if (host->timing != MMC_TIMING_MMC_HS200 &&
+ host->timing != MMC_TIMING_MMC_HS400 &&
host->timing != MMC_TIMING_UHS_SDR104)
goto disable;
mci_writel(host, CMDARG, arg);
wmb();
+ dw_mci_wait_while_busy(host, cmd);
mci_writel(host, CMD, SDMMC_CMD_START | cmd);
while (time_before(jiffies, timeout)) {
dw_mci_start_command(host, cmd, cmdflags);
+ if (cmd->opcode == SD_SWITCH_VOLTAGE) {
+ /*
+ * Databook says to fail after 2ms w/ no response; give an
+ * extra jiffy just in case we're about to roll over.
+ */
+ mod_timer(&host->cmd11_timer,
+ jiffies + msecs_to_jiffies(2) + 1);
+ }
+
if (mrq->stop)
host->stop_cmdr = dw_mci_prepare_command(slot->mmc, mrq->stop);
else
regs = mci_readl(slot->host, UHS_REG);
/* DDR mode set */
- if (ios->timing == MMC_TIMING_MMC_DDR52)
+ if (ios->timing == MMC_TIMING_MMC_DDR52 ||
+ ios->timing == MMC_TIMING_MMC_HS400)
regs |= ((0x1 << slot->id) << 16);
else
regs &= ~((0x1 << slot->id) << 16);
if (drv_data && drv_data->set_ios)
drv_data->set_ios(slot->host, ios);
- /* Slot specific timing and width adjustment */
- dw_mci_setup_bus(slot, false);
-
- if (slot->host->state == STATE_WAITING_CMD11_DONE && ios->clock != 0)
- slot->host->state = STATE_IDLE;
-
switch (ios->power_mode) {
case MMC_POWER_UP:
if (!IS_ERR(mmc->supply.vmmc)) {
mci_writel(slot->host, PWREN, regs);
break;
case MMC_POWER_ON:
- if (!IS_ERR(mmc->supply.vqmmc) && !slot->host->vqmmc_enabled) {
- ret = regulator_enable(mmc->supply.vqmmc);
- if (ret < 0)
- dev_err(slot->host->dev,
- "failed to enable vqmmc regulator\n");
- else
+ if (!slot->host->vqmmc_enabled) {
+ if (!IS_ERR(mmc->supply.vqmmc)) {
+ ret = regulator_enable(mmc->supply.vqmmc);
+ if (ret < 0)
+ dev_err(slot->host->dev,
+ "failed to enable vqmmc\n");
+ else
+ slot->host->vqmmc_enabled = true;
+
+ } else {
+ /* Keep track so we don't reset again */
slot->host->vqmmc_enabled = true;
+ }
+
+ /* Reset our state machine after powering on */
+ dw_mci_ctrl_reset(slot->host,
+ SDMMC_CTRL_ALL_RESET_FLAGS);
}
+
+ /* Adjust clock / bus width after power is up */
+ dw_mci_setup_bus(slot, false);
+
break;
case MMC_POWER_OFF:
+ /* Turn clock off before power goes down */
+ dw_mci_setup_bus(slot, false);
+
if (!IS_ERR(mmc->supply.vmmc))
mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
- if (!IS_ERR(mmc->supply.vqmmc) && slot->host->vqmmc_enabled) {
+ if (!IS_ERR(mmc->supply.vqmmc) && slot->host->vqmmc_enabled)
regulator_disable(mmc->supply.vqmmc);
- slot->host->vqmmc_enabled = false;
- }
+ slot->host->vqmmc_enabled = false;
regs = mci_readl(slot->host, PWREN);
regs &= ~(1 << slot->id);
default:
break;
}
+
+ if (slot->host->state == STATE_WAITING_CMD11_DONE && ios->clock != 0)
+ slot->host->state = STATE_IDLE;
}
static int dw_mci_card_busy(struct mmc_host *mmc)
return err;
}
+static int dw_mci_prepare_hs400_tuning(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ struct dw_mci_slot *slot = mmc_priv(mmc);
+ struct dw_mci *host = slot->host;
+ const struct dw_mci_drv_data *drv_data = host->drv_data;
+
+ if (drv_data && drv_data->prepare_hs400_tuning)
+ return drv_data->prepare_hs400_tuning(host, ios);
+
+ return 0;
+}
+
static const struct mmc_host_ops dw_mci_ops = {
.request = dw_mci_request,
.pre_req = dw_mci_pre_req,
.card_busy = dw_mci_card_busy,
.start_signal_voltage_switch = dw_mci_switch_voltage,
.init_card = dw_mci_init_card,
+ .prepare_hs400_tuning = dw_mci_prepare_hs400_tuning,
};
static void dw_mci_request_end(struct dw_mci *host, struct mmc_request *mrq)
if (test_and_clear_bit(EVENT_DATA_ERROR,
&host->pending_events)) {
dw_mci_stop_dma(host);
- send_stop_abort(host, data);
+ if (data->stop ||
+ !(host->data_status & (SDMMC_INT_DRTO |
+ SDMMC_INT_EBE)))
+ send_stop_abort(host, data);
state = STATE_DATA_ERROR;
break;
}
if (test_and_clear_bit(EVENT_DATA_ERROR,
&host->pending_events)) {
dw_mci_stop_dma(host);
- send_stop_abort(host, data);
+ if (data->stop ||
+ !(host->data_status & (SDMMC_INT_DRTO |
+ SDMMC_INT_EBE)))
+ send_stop_abort(host, data);
state = STATE_DATA_ERROR;
break;
}
/* Check volt switch first, since it can look like an error */
if ((host->state == STATE_SENDING_CMD11) &&
(pending & SDMMC_INT_VOLT_SWITCH)) {
+ del_timer(&host->cmd11_timer);
+
mci_writel(host, RINTSTS, SDMMC_INT_VOLT_SWITCH);
pending &= ~SDMMC_INT_VOLT_SWITCH;
dw_mci_cmd_interrupt(host, pending);
/* Handle SDIO Interrupts */
for (i = 0; i < host->num_slots; i++) {
struct dw_mci_slot *slot = host->slot[i];
+
+ if (!slot)
+ continue;
+
if (pending & SDMMC_INT_SDIO(slot->sdio_id)) {
mci_writel(host, RINTSTS,
SDMMC_INT_SDIO(slot->sdio_id));
return ret;
}
+static void dw_mci_cmd11_timer(unsigned long arg)
+{
+ struct dw_mci *host = (struct dw_mci *)arg;
+
+ if (host->state != STATE_SENDING_CMD11)
+ dev_info(host->dev, "Unexpected CMD11 timeout\n");
+
+ host->cmd_status = SDMMC_INT_RTO;
+ set_bit(EVENT_CMD_COMPLETE, &host->pending_events);
+ tasklet_schedule(&host->tasklet);
+}
+
#ifdef CONFIG_OF
static struct dw_mci_of_quirks {
char *quirk;
}
#endif /* CONFIG_OF */
+static void dw_mci_enable_cd(struct dw_mci *host)
+{
+ struct dw_mci_board *brd = host->pdata;
+ unsigned long irqflags;
+ u32 temp;
+ int i;
+
+ /* No need for CD if broken card detection */
+ if (brd->quirks & DW_MCI_QUIRK_BROKEN_CARD_DETECTION)
+ return;
+
+ /* No need for CD if all slots have a non-error GPIO */
+ for (i = 0; i < host->num_slots; i++) {
+ struct dw_mci_slot *slot = host->slot[i];
+
+ if (IS_ERR_VALUE(mmc_gpio_get_cd(slot->mmc)))
+ break;
+ }
+ if (i == host->num_slots)
+ return;
+
+ spin_lock_irqsave(&host->irq_lock, irqflags);
+ temp = mci_readl(host, INTMASK);
+ temp |= SDMMC_INT_CD;
+ mci_writel(host, INTMASK, temp);
+ spin_unlock_irqrestore(&host->irq_lock, irqflags);
+}
+
int dw_mci_probe(struct dw_mci *host)
{
const struct dw_mci_drv_data *drv_data = host->drv_data;
}
}
+ setup_timer(&host->cmd11_timer,
+ dw_mci_cmd11_timer, (unsigned long)host);
+
host->quirks = host->pdata->quirks;
spin_lock_init(&host->lock);
host->num_slots = ((mci_readl(host, HCON) >> 1) & 0x1F) + 1;
/*
- * Enable interrupts for command done, data over, data empty, card det,
+ * Enable interrupts for command done, data over, data empty,
* receive ready and error such as transmit, receive timeout, crc error
*/
mci_writel(host, RINTSTS, 0xFFFFFFFF);
mci_writel(host, INTMASK, SDMMC_INT_CMD_DONE | SDMMC_INT_DATA_OVER |
SDMMC_INT_TXDR | SDMMC_INT_RXDR |
- DW_MCI_ERROR_FLAGS | SDMMC_INT_CD);
+ DW_MCI_ERROR_FLAGS);
mci_writel(host, CTRL, SDMMC_CTRL_INT_ENABLE); /* Enable mci interrupt */
dev_info(host->dev, "DW MMC controller at irq %d, "
init_slots++;
}
+ /* Now that slots are all setup, we can enable card detect */
+ dw_mci_enable_cd(host);
+
if (init_slots) {
dev_info(host->dev, "%d slots initialized\n", init_slots);
} else {
mci_writel(host, RINTSTS, 0xFFFFFFFF);
mci_writel(host, INTMASK, SDMMC_INT_CMD_DONE | SDMMC_INT_DATA_OVER |
SDMMC_INT_TXDR | SDMMC_INT_RXDR |
- DW_MCI_ERROR_FLAGS | SDMMC_INT_CD);
+ DW_MCI_ERROR_FLAGS);
mci_writel(host, CTRL, SDMMC_CTRL_INT_ENABLE);
for (i = 0; i < host->num_slots; i++) {
dw_mci_setup_bus(slot, true);
}
}
+
+ /* Now that slots are all setup, we can enable card detect */
+ dw_mci_enable_cd(host);
+
return 0;
}
EXPORT_SYMBOL(dw_mci_resume);