#include "bnx2x.h"
#include "bnx2x_init.h"
+#include "bnx2x_init_ops.h"
#include "bnx2x_dump.h"
-#define DRV_MODULE_VERSION "1.48.105"
-#define DRV_MODULE_RELDATE "2009/03/02"
+#define DRV_MODULE_VERSION "1.48.114-1"
+#define DRV_MODULE_RELDATE "2009/07/29"
#define BNX2X_BC_VER 0x040200
+#include <linux/firmware.h>
+#include "bnx2x_fw_file_hdr.h"
+/* FW files */
+#define FW_FILE_PREFIX_E1 "bnx2x-e1-"
+#define FW_FILE_PREFIX_E1H "bnx2x-e1h-"
+
/* Time in jiffies before concluding the transmitter is hung */
#define TX_TIMEOUT (5*HZ)
val, port, addr, (msix ? "MSI-X" : (msi ? "MSI" : "INTx")));
REG_WR(bp, addr, val);
+ /*
+ * Ensure that HC_CONFIG is written before leading/trailing edge config
+ */
+ mmiowb();
+ barrier();
if (CHIP_IS_E1H(bp)) {
/* init leading/trailing edge */
REG_WR(bp, HC_REG_TRAILING_EDGE_0 + port*8, val);
REG_WR(bp, HC_REG_LEADING_EDGE_0 + port*8, val);
}
+
+ /* Make sure that interrupts are indeed enabled from here on */
+ mmiowb();
}
static void bnx2x_int_disable(struct bnx2x *bp)
/* disable interrupt handling */
atomic_inc(&bp->intr_sem);
+ smp_wmb(); /* Ensure that bp->intr_sem update is SMP-safe */
+
if (disable_hw)
/* prevent the HW from sending interrupts */
bnx2x_int_disable(bp);
DP(BNX2X_MSG_OFF, "write 0x%08x to HC addr 0x%x\n",
(*(u32 *)&igu_ack), hc_addr);
REG_WR(bp, hc_addr, (*(u32 *)&igu_ack));
+
+ /* Make sure that ACK is written */
+ mmiowb();
+ barrier();
}
static inline u16 bnx2x_update_fpsb_idx(struct bnx2x_fastpath *fp)
len, cqe, comp_ring_cons);
#ifdef BNX2X_STOP_ON_ERROR
if (bp->panic)
- return -EINVAL;
+ return 0;
#endif
bnx2x_update_sge_prod(fp,
bp->spq_prod_idx++;
}
+ /* Make sure that BD data is updated before writing the producer */
+ wmb();
+
REG_WR(bp, BAR_XSTRORM_INTMEM + XSTORM_SPQ_PROD_OFFSET(func),
bp->spq_prod_idx);
+ mmiowb();
+
spin_unlock_bh(&bp->spq_lock);
return 0;
}
}
}
+static inline void bnx2x_fan_failure(struct bnx2x *bp)
+{
+ int port = BP_PORT(bp);
+
+ /* mark the failure */
+ bp->link_params.ext_phy_config &= ~PORT_HW_CFG_XGXS_EXT_PHY_TYPE_MASK;
+ bp->link_params.ext_phy_config |= PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE;
+ SHMEM_WR(bp, dev_info.port_hw_config[port].external_phy_config,
+ bp->link_params.ext_phy_config);
+
+ /* log the failure */
+ printk(KERN_ERR PFX "Fan Failure on Network Controller %s has caused"
+ " the driver to shutdown the card to prevent permanent"
+ " damage. Please contact Dell Support for assistance\n",
+ bp->dev->name);
+}
static inline void bnx2x_attn_int_deasserted0(struct bnx2x *bp, u32 attn)
{
int port = BP_PORT(bp);
int reg_offset;
- u32 val;
+ u32 val, swap_val, swap_override;
reg_offset = (port ? MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0 :
MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0);
BNX2X_ERR("SPIO5 hw attention\n");
+ /* Fan failure attention */
switch (XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config)) {
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
- /* Fan failure attention */
-
+ /* Low power mode is controlled by GPIO 2 */
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
+ MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
/* The PHY reset is controlled by GPIO 1 */
bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
- /* Low power mode is controlled by GPIO 2 */
- bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_2,
+ break;
+
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
+ /* The PHY reset is controlled by GPIO 1 */
+ /* fake the port number to cancel the swap done in
+ set_gpio() */
+ swap_val = REG_RD(bp, NIG_REG_PORT_SWAP);
+ swap_override = REG_RD(bp, NIG_REG_STRAP_OVERRIDE);
+ port = (swap_val && swap_override) ^ 1;
+ bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_1,
MISC_REGISTERS_GPIO_OUTPUT_LOW, port);
- /* mark the failure */
- bp->link_params.ext_phy_config &=
- ~PORT_HW_CFG_XGXS_EXT_PHY_TYPE_MASK;
- bp->link_params.ext_phy_config |=
- PORT_HW_CFG_XGXS_EXT_PHY_TYPE_FAILURE;
- SHMEM_WR(bp,
- dev_info.port_hw_config[port].
- external_phy_config,
- bp->link_params.ext_phy_config);
- /* log the failure */
- printk(KERN_ERR PFX "Fan Failure on Network"
- " Controller %s has caused the driver to"
- " shutdown the card to prevent permanent"
- " damage. Please contact Dell Support for"
- " assistance\n", bp->dev->name);
break;
default:
break;
}
+ bnx2x_fan_failure(bp);
}
if (attn & (AEU_INPUTS_ATTN_BITS_GPIO3_FUNCTION_0 |
REG_WR16(bp, BAR_USTRORM_INTMEM +
USTORM_SB_HC_DISABLE_OFFSET(port, sb_id,
U_SB_ETH_RX_CQ_INDEX),
- bp->rx_ticks ? 0 : 1);
+ (bp->rx_ticks/12) ? 0 : 1);
/* HC_INDEX_C_ETH_TX_CQ_CONS */
REG_WR8(bp, BAR_CSTRORM_INTMEM +
REG_WR16(bp, BAR_CSTRORM_INTMEM +
CSTORM_SB_HC_DISABLE_OFFSET(port, sb_id,
C_SB_ETH_TX_CQ_INDEX),
- bp->tx_ticks ? 0 : 1);
+ (bp->tx_ticks/12) ? 0 : 1);
}
}
int mode = bp->rx_mode;
int mask = (1 << BP_L_ID(bp));
int func = BP_FUNC(bp);
+ int port = BP_PORT(bp);
int i;
+ /* All but management unicast packets should pass to the host as well */
+ u32 llh_mask =
+ NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_BRCST |
+ NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_MLCST |
+ NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_VLAN |
+ NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_NO_VLAN;
DP(NETIF_MSG_IFUP, "rx mode %d mask 0x%x\n", mode, mask);
tstorm_mac_filter.ucast_accept_all = mask;
tstorm_mac_filter.mcast_accept_all = mask;
tstorm_mac_filter.bcast_accept_all = mask;
+ /* pass management unicast packets as well */
+ llh_mask |= NIG_LLH0_BRB1_DRV_MASK_REG_LLH0_BRB1_DRV_MASK_UNCST;
break;
default:
break;
}
+ REG_WR(bp,
+ (port ? NIG_REG_LLH1_BRB1_DRV_MASK : NIG_REG_LLH0_BRB1_DRV_MASK),
+ llh_mask);
+
for (i = 0; i < sizeof(struct tstorm_eth_mac_filter_config)/4; i++) {
REG_WR(bp, BAR_TSTRORM_INTMEM +
TSTORM_MAC_FILTER_CONFIG_OFFSET(func) + i * 4,
mmiowb();
bnx2x_int_enable(bp);
+
+ /* Check for SPIO5 */
+ bnx2x_attn_int_deasserted0(bp,
+ REG_RD(bp, MISC_REG_AEU_AFTER_INVERT_1_FUNC_0 + BP_PORT(bp)*4) &
+ AEU_INPUTS_ATTN_BITS_SPIO5);
}
/* end of nic init */
}
}
-static int bnx2x_gunzip(struct bnx2x *bp, u8 *zbuf, int len)
+static int bnx2x_gunzip(struct bnx2x *bp, const u8 *zbuf, int len)
{
int n, rc;
/* check gzip header */
- if ((zbuf[0] != 0x1f) || (zbuf[1] != 0x8b) || (zbuf[2] != Z_DEFLATED))
+ if ((zbuf[0] != 0x1f) || (zbuf[1] != 0x8b) || (zbuf[2] != Z_DEFLATED)) {
+ BNX2X_ERR("Bad gzip header\n");
return -EINVAL;
+ }
n = 10;
if (zbuf[3] & FNAME)
while ((zbuf[n++] != 0) && (n < len));
- bp->strm->next_in = zbuf + n;
+ bp->strm->next_in = (typeof(bp->strm->next_in))zbuf + n;
bp->strm->avail_in = len - n;
bp->strm->next_out = bp->gunzip_buf;
bp->strm->avail_out = FW_BUF_SIZE;
msleep(50);
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_SET, 0x03);
msleep(50);
- bnx2x_init_block(bp, BRB1_COMMON_START, BRB1_COMMON_END);
- bnx2x_init_block(bp, PRS_COMMON_START, PRS_COMMON_END);
+ bnx2x_init_block(bp, BRB1_BLOCK, COMMON_STAGE);
+ bnx2x_init_block(bp, PRS_BLOCK, COMMON_STAGE);
DP(NETIF_MSG_HW, "part2\n");
msleep(50);
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_SET, 0x03);
msleep(50);
- bnx2x_init_block(bp, BRB1_COMMON_START, BRB1_COMMON_END);
- bnx2x_init_block(bp, PRS_COMMON_START, PRS_COMMON_END);
+ bnx2x_init_block(bp, BRB1_BLOCK, COMMON_STAGE);
+ bnx2x_init_block(bp, PRS_BLOCK, COMMON_STAGE);
#ifndef BCM_ISCSI
/* set NIC mode */
REG_WR(bp, PRS_REG_NIC_MODE, 1);
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, 0x1403);
}
+
+static void bnx2x_setup_fan_failure_detection(struct bnx2x *bp)
+{
+ u32 val;
+ u8 port;
+ u8 is_required = 0;
+
+ val = SHMEM_RD(bp, dev_info.shared_hw_config.config2) &
+ SHARED_HW_CFG_FAN_FAILURE_MASK;
+
+ if (val == SHARED_HW_CFG_FAN_FAILURE_ENABLED)
+ is_required = 1;
+
+ /*
+ * The fan failure mechanism is usually related to the PHY type since
+ * the power consumption of the board is affected by the PHY. Currently,
+ * fan is required for most designs with SFX7101, BCM8727 and BCM8481.
+ */
+ else if (val == SHARED_HW_CFG_FAN_FAILURE_PHY_TYPE)
+ for (port = PORT_0; port < PORT_MAX; port++) {
+ u32 phy_type =
+ SHMEM_RD(bp, dev_info.port_hw_config[port].
+ external_phy_config) &
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_MASK;
+ is_required |=
+ ((phy_type ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101) ||
+ (phy_type ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727) ||
+ (phy_type ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8481));
+ }
+
+ DP(NETIF_MSG_HW, "fan detection setting: %d\n", is_required);
+
+ if (is_required == 0)
+ return;
+
+ /* Fan failure is indicated by SPIO 5 */
+ bnx2x_set_spio(bp, MISC_REGISTERS_SPIO_5,
+ MISC_REGISTERS_SPIO_INPUT_HI_Z);
+
+ /* set to active low mode */
+ val = REG_RD(bp, MISC_REG_SPIO_INT);
+ val |= ((1 << MISC_REGISTERS_SPIO_5) <<
+ MISC_REGISTERS_SPIO_INT_OLD_SET_POS);
+ REG_WR(bp, MISC_REG_SPIO_INT, val);
+
+ /* enable interrupt to signal the IGU */
+ val = REG_RD(bp, MISC_REG_SPIO_EVENT_EN);
+ val |= (1 << MISC_REGISTERS_SPIO_5);
+ REG_WR(bp, MISC_REG_SPIO_EVENT_EN, val);
+}
+
static int bnx2x_init_common(struct bnx2x *bp)
{
u32 val, i;
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_SET, 0xffffffff);
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_SET, 0xfffc);
- bnx2x_init_block(bp, MISC_COMMON_START, MISC_COMMON_END);
+ bnx2x_init_block(bp, MISC_BLOCK, COMMON_STAGE);
if (CHIP_IS_E1H(bp))
REG_WR(bp, MISC_REG_E1HMF_MODE, IS_E1HMF(bp));
msleep(30);
REG_WR(bp, MISC_REG_LCPLL_CTRL_REG_2, 0x0);
- bnx2x_init_block(bp, PXP_COMMON_START, PXP_COMMON_END);
+ bnx2x_init_block(bp, PXP_BLOCK, COMMON_STAGE);
if (CHIP_IS_E1(bp)) {
/* enable HW interrupt from PXP on USDM overflow
bit 16 on INT_MASK_0 */
REG_WR(bp, PXP_REG_PXP_INT_MASK_0, 0);
}
- bnx2x_init_block(bp, PXP2_COMMON_START, PXP2_COMMON_END);
+ bnx2x_init_block(bp, PXP2_BLOCK, COMMON_STAGE);
bnx2x_init_pxp(bp);
#ifdef __BIG_ENDIAN
REG_WR(bp, PXP2_REG_RQ_DISABLE_INPUTS, 0);
REG_WR(bp, PXP2_REG_RD_DISABLE_INPUTS, 0);
- bnx2x_init_block(bp, DMAE_COMMON_START, DMAE_COMMON_END);
+ bnx2x_init_block(bp, DMAE_BLOCK, COMMON_STAGE);
/* clean the DMAE memory */
bp->dmae_ready = 1;
bnx2x_init_fill(bp, TSEM_REG_PRAM, 0, 8);
- bnx2x_init_block(bp, TCM_COMMON_START, TCM_COMMON_END);
- bnx2x_init_block(bp, UCM_COMMON_START, UCM_COMMON_END);
- bnx2x_init_block(bp, CCM_COMMON_START, CCM_COMMON_END);
- bnx2x_init_block(bp, XCM_COMMON_START, XCM_COMMON_END);
+ bnx2x_init_block(bp, TCM_BLOCK, COMMON_STAGE);
+ bnx2x_init_block(bp, UCM_BLOCK, COMMON_STAGE);
+ bnx2x_init_block(bp, CCM_BLOCK, COMMON_STAGE);
+ bnx2x_init_block(bp, XCM_BLOCK, COMMON_STAGE);
bnx2x_read_dmae(bp, XSEM_REG_PASSIVE_BUFFER, 3);
bnx2x_read_dmae(bp, CSEM_REG_PASSIVE_BUFFER, 3);
bnx2x_read_dmae(bp, TSEM_REG_PASSIVE_BUFFER, 3);
bnx2x_read_dmae(bp, USEM_REG_PASSIVE_BUFFER, 3);
- bnx2x_init_block(bp, QM_COMMON_START, QM_COMMON_END);
+ bnx2x_init_block(bp, QM_BLOCK, COMMON_STAGE);
/* soft reset pulse */
REG_WR(bp, QM_REG_SOFT_RESET, 1);
REG_WR(bp, QM_REG_SOFT_RESET, 0);
#ifdef BCM_ISCSI
- bnx2x_init_block(bp, TIMERS_COMMON_START, TIMERS_COMMON_END);
+ bnx2x_init_block(bp, TIMERS_BLOCK, COMMON_STAGE);
#endif
- bnx2x_init_block(bp, DQ_COMMON_START, DQ_COMMON_END);
+ bnx2x_init_block(bp, DQ_BLOCK, COMMON_STAGE);
REG_WR(bp, DORQ_REG_DPM_CID_OFST, BCM_PAGE_SHIFT);
if (!CHIP_REV_IS_SLOW(bp)) {
/* enable hw interrupt from doorbell Q */
REG_WR(bp, DORQ_REG_DORQ_INT_MASK, 0);
}
- bnx2x_init_block(bp, BRB1_COMMON_START, BRB1_COMMON_END);
- bnx2x_init_block(bp, PRS_COMMON_START, PRS_COMMON_END);
+ bnx2x_init_block(bp, BRB1_BLOCK, COMMON_STAGE);
+ bnx2x_init_block(bp, PRS_BLOCK, COMMON_STAGE);
REG_WR(bp, PRS_REG_A_PRSU_20, 0xf);
/* set NIC mode */
REG_WR(bp, PRS_REG_NIC_MODE, 1);
if (CHIP_IS_E1H(bp))
REG_WR(bp, PRS_REG_E1HOV_MODE, IS_E1HMF(bp));
- bnx2x_init_block(bp, TSDM_COMMON_START, TSDM_COMMON_END);
- bnx2x_init_block(bp, CSDM_COMMON_START, CSDM_COMMON_END);
- bnx2x_init_block(bp, USDM_COMMON_START, USDM_COMMON_END);
- bnx2x_init_block(bp, XSDM_COMMON_START, XSDM_COMMON_END);
+ bnx2x_init_block(bp, TSDM_BLOCK, COMMON_STAGE);
+ bnx2x_init_block(bp, CSDM_BLOCK, COMMON_STAGE);
+ bnx2x_init_block(bp, USDM_BLOCK, COMMON_STAGE);
+ bnx2x_init_block(bp, XSDM_BLOCK, COMMON_STAGE);
bnx2x_init_fill(bp, TSTORM_INTMEM_ADDR, 0, STORM_INTMEM_SIZE(bp));
bnx2x_init_fill(bp, USTORM_INTMEM_ADDR, 0, STORM_INTMEM_SIZE(bp));
bnx2x_init_fill(bp, CSTORM_INTMEM_ADDR, 0, STORM_INTMEM_SIZE(bp));
bnx2x_init_fill(bp, XSTORM_INTMEM_ADDR, 0, STORM_INTMEM_SIZE(bp));
- bnx2x_init_block(bp, TSEM_COMMON_START, TSEM_COMMON_END);
- bnx2x_init_block(bp, USEM_COMMON_START, USEM_COMMON_END);
- bnx2x_init_block(bp, CSEM_COMMON_START, CSEM_COMMON_END);
- bnx2x_init_block(bp, XSEM_COMMON_START, XSEM_COMMON_END);
+ bnx2x_init_block(bp, TSEM_BLOCK, COMMON_STAGE);
+ bnx2x_init_block(bp, USEM_BLOCK, COMMON_STAGE);
+ bnx2x_init_block(bp, CSEM_BLOCK, COMMON_STAGE);
+ bnx2x_init_block(bp, XSEM_BLOCK, COMMON_STAGE);
/* sync semi rtc */
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_CLEAR,
REG_WR(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_SET,
0x80000000);
- bnx2x_init_block(bp, UPB_COMMON_START, UPB_COMMON_END);
- bnx2x_init_block(bp, XPB_COMMON_START, XPB_COMMON_END);
- bnx2x_init_block(bp, PBF_COMMON_START, PBF_COMMON_END);
+ bnx2x_init_block(bp, UPB_BLOCK, COMMON_STAGE);
+ bnx2x_init_block(bp, XPB_BLOCK, COMMON_STAGE);
+ bnx2x_init_block(bp, PBF_BLOCK, COMMON_STAGE);
REG_WR(bp, SRC_REG_SOFT_RST, 1);
for (i = SRC_REG_KEYRSS0_0; i <= SRC_REG_KEYRSS1_9; i += 4) {
REG_WR(bp, i, 0xc0cac01a);
/* TODO: replace with something meaningful */
}
- bnx2x_init_block(bp, SRCH_COMMON_START, SRCH_COMMON_END);
+ bnx2x_init_block(bp, SRCH_BLOCK, COMMON_STAGE);
REG_WR(bp, SRC_REG_SOFT_RST, 0);
if (sizeof(union cdu_context) != 1024)
printk(KERN_ALERT PFX "please adjust the size of"
" cdu_context(%ld)\n", (long)sizeof(union cdu_context));
- bnx2x_init_block(bp, CDU_COMMON_START, CDU_COMMON_END);
+ bnx2x_init_block(bp, CDU_BLOCK, COMMON_STAGE);
val = (4 << 24) + (0 << 12) + 1024;
REG_WR(bp, CDU_REG_CDU_GLOBAL_PARAMS, val);
if (CHIP_IS_E1(bp)) {
REG_WR(bp, CDU_REG_CDU_DEBUG, 0);
}
- bnx2x_init_block(bp, CFC_COMMON_START, CFC_COMMON_END);
+ bnx2x_init_block(bp, CFC_BLOCK, COMMON_STAGE);
REG_WR(bp, CFC_REG_INIT_REG, 0x7FF);
/* enable context validation interrupt from CFC */
REG_WR(bp, CFC_REG_CFC_INT_MASK, 0);
/* set the thresholds to prevent CFC/CDU race */
REG_WR(bp, CFC_REG_DEBUG0, 0x20020000);
- bnx2x_init_block(bp, HC_COMMON_START, HC_COMMON_END);
- bnx2x_init_block(bp, MISC_AEU_COMMON_START, MISC_AEU_COMMON_END);
+ bnx2x_init_block(bp, HC_BLOCK, COMMON_STAGE);
+ bnx2x_init_block(bp, MISC_AEU_BLOCK, COMMON_STAGE);
/* PXPCS COMMON comes here */
+ bnx2x_init_block(bp, PXPCS_BLOCK, COMMON_STAGE);
/* Reset PCIE errors for debug */
REG_WR(bp, 0x2814, 0xffffffff);
REG_WR(bp, 0x3820, 0xffffffff);
/* EMAC0 COMMON comes here */
+ bnx2x_init_block(bp, EMAC0_BLOCK, COMMON_STAGE);
/* EMAC1 COMMON comes here */
+ bnx2x_init_block(bp, EMAC1_BLOCK, COMMON_STAGE);
/* DBU COMMON comes here */
+ bnx2x_init_block(bp, DBU_BLOCK, COMMON_STAGE);
/* DBG COMMON comes here */
+ bnx2x_init_block(bp, DBG_BLOCK, COMMON_STAGE);
- bnx2x_init_block(bp, NIG_COMMON_START, NIG_COMMON_END);
+ bnx2x_init_block(bp, NIG_BLOCK, COMMON_STAGE);
if (CHIP_IS_E1H(bp)) {
REG_WR(bp, NIG_REG_LLH_MF_MODE, IS_E1HMF(bp));
REG_WR(bp, NIG_REG_LLH_E1HOV_MODE, IS_E1HMF(bp));
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8072:
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8073:
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
bp->port.need_hw_lock = 1;
break;
- case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
- /* Fan failure is indicated by SPIO 5 */
- bnx2x_set_spio(bp, MISC_REGISTERS_SPIO_5,
- MISC_REGISTERS_SPIO_INPUT_HI_Z);
-
- /* set to active low mode */
- val = REG_RD(bp, MISC_REG_SPIO_INT);
- val |= ((1 << MISC_REGISTERS_SPIO_5) <<
- MISC_REGISTERS_SPIO_INT_OLD_SET_POS);
- REG_WR(bp, MISC_REG_SPIO_INT, val);
-
- /* enable interrupt to signal the IGU */
- val = REG_RD(bp, MISC_REG_SPIO_EVENT_EN);
- val |= (1 << MISC_REGISTERS_SPIO_5);
- REG_WR(bp, MISC_REG_SPIO_EVENT_EN, val);
- break;
-
default:
break;
}
+ bnx2x_setup_fan_failure_detection(bp);
+
/* clear PXP2 attentions */
REG_RD(bp, PXP2_REG_PXP2_INT_STS_CLR_0);
static int bnx2x_init_port(struct bnx2x *bp)
{
int port = BP_PORT(bp);
+ int init_stage = port ? PORT1_STAGE : PORT0_STAGE;
u32 low, high;
u32 val;
REG_WR(bp, NIG_REG_MASK_INTERRUPT_PORT0 + port*4, 0);
/* Port PXP comes here */
+ bnx2x_init_block(bp, PXP_BLOCK, init_stage);
/* Port PXP2 comes here */
+ bnx2x_init_block(bp, PXP2_BLOCK, init_stage);
#ifdef BCM_ISCSI
/* Port0 1
* Port1 385 */
REG_WR(bp, PXP2_REG_PSWRQ_SRC0_L2P + func*4, PXP_ONE_ILT(i));
#endif
/* Port CMs come here */
- bnx2x_init_block(bp, (port ? XCM_PORT1_START : XCM_PORT0_START),
- (port ? XCM_PORT1_END : XCM_PORT0_END));
+ bnx2x_init_block(bp, XCM_BLOCK, init_stage);
/* Port QM comes here */
#ifdef BCM_ISCSI
REG_WR(bp, TM_REG_LIN0_SCAN_TIME + func*4, 1024/64*20);
REG_WR(bp, TM_REG_LIN0_MAX_ACTIVE_CID + func*4, 31);
- bnx2x_init_block(bp, func ? TIMERS_PORT1_START : TIMERS_PORT0_START,
- func ? TIMERS_PORT1_END : TIMERS_PORT0_END);
+ bnx2x_init_block(bp, TIMERS_BLOCK, init_stage);
#endif
/* Port DQ comes here */
+ bnx2x_init_block(bp, DQ_BLOCK, init_stage);
- bnx2x_init_block(bp, (port ? BRB1_PORT1_START : BRB1_PORT0_START),
- (port ? BRB1_PORT1_END : BRB1_PORT0_END));
+ bnx2x_init_block(bp, BRB1_BLOCK, init_stage);
if (CHIP_REV_IS_SLOW(bp) && !CHIP_IS_E1H(bp)) {
/* no pause for emulation and FPGA */
low = 0;
/* Port PRS comes here */
+ bnx2x_init_block(bp, PRS_BLOCK, init_stage);
/* Port TSDM comes here */
+ bnx2x_init_block(bp, TSDM_BLOCK, init_stage);
/* Port CSDM comes here */
+ bnx2x_init_block(bp, CSDM_BLOCK, init_stage);
/* Port USDM comes here */
+ bnx2x_init_block(bp, USDM_BLOCK, init_stage);
/* Port XSDM comes here */
+ bnx2x_init_block(bp, XSDM_BLOCK, init_stage);
- bnx2x_init_block(bp, port ? TSEM_PORT1_START : TSEM_PORT0_START,
- port ? TSEM_PORT1_END : TSEM_PORT0_END);
- bnx2x_init_block(bp, port ? USEM_PORT1_START : USEM_PORT0_START,
- port ? USEM_PORT1_END : USEM_PORT0_END);
- bnx2x_init_block(bp, port ? CSEM_PORT1_START : CSEM_PORT0_START,
- port ? CSEM_PORT1_END : CSEM_PORT0_END);
- bnx2x_init_block(bp, port ? XSEM_PORT1_START : XSEM_PORT0_START,
- port ? XSEM_PORT1_END : XSEM_PORT0_END);
+ bnx2x_init_block(bp, TSEM_BLOCK, init_stage);
+ bnx2x_init_block(bp, USEM_BLOCK, init_stage);
+ bnx2x_init_block(bp, CSEM_BLOCK, init_stage);
+ bnx2x_init_block(bp, XSEM_BLOCK, init_stage);
/* Port UPB comes here */
+ bnx2x_init_block(bp, UPB_BLOCK, init_stage);
/* Port XPB comes here */
+ bnx2x_init_block(bp, XPB_BLOCK, init_stage);
- bnx2x_init_block(bp, port ? PBF_PORT1_START : PBF_PORT0_START,
- port ? PBF_PORT1_END : PBF_PORT0_END);
+ bnx2x_init_block(bp, PBF_BLOCK, init_stage);
/* configure PBF to work without PAUSE mtu 9000 */
REG_WR(bp, PBF_REG_P0_PAUSE_ENABLE + port*4, 0);
/* Port SRCH comes here */
#endif
/* Port CDU comes here */
+ bnx2x_init_block(bp, CDU_BLOCK, init_stage);
/* Port CFC comes here */
+ bnx2x_init_block(bp, CFC_BLOCK, init_stage);
if (CHIP_IS_E1(bp)) {
REG_WR(bp, HC_REG_LEADING_EDGE_0 + port*8, 0);
REG_WR(bp, HC_REG_TRAILING_EDGE_0 + port*8, 0);
}
- bnx2x_init_block(bp, port ? HC_PORT1_START : HC_PORT0_START,
- port ? HC_PORT1_END : HC_PORT0_END);
+ bnx2x_init_block(bp, HC_BLOCK, init_stage);
- bnx2x_init_block(bp, port ? MISC_AEU_PORT1_START :
- MISC_AEU_PORT0_START,
- port ? MISC_AEU_PORT1_END : MISC_AEU_PORT0_END);
+ bnx2x_init_block(bp, MISC_AEU_BLOCK, init_stage);
/* init aeu_mask_attn_func_0/1:
* - SF mode: bits 3-7 are masked. only bits 0-2 are in use
* - MF mode: bit 3 is masked. bits 0-2 are in use as in SF
(IS_E1HMF(bp) ? 0xF7 : 0x7));
/* Port PXPCS comes here */
+ bnx2x_init_block(bp, PXPCS_BLOCK, init_stage);
/* Port EMAC0 comes here */
+ bnx2x_init_block(bp, EMAC0_BLOCK, init_stage);
/* Port EMAC1 comes here */
+ bnx2x_init_block(bp, EMAC1_BLOCK, init_stage);
/* Port DBU comes here */
+ bnx2x_init_block(bp, DBU_BLOCK, init_stage);
/* Port DBG comes here */
+ bnx2x_init_block(bp, DBG_BLOCK, init_stage);
- bnx2x_init_block(bp, port ? NIG_PORT1_START : NIG_PORT0_START,
- port ? NIG_PORT1_END : NIG_PORT0_END);
+ bnx2x_init_block(bp, NIG_BLOCK, init_stage);
REG_WR(bp, NIG_REG_XGXS_SERDES0_MODE_SEL + port*4, 1);
}
/* Port MCP comes here */
+ bnx2x_init_block(bp, MCP_BLOCK, init_stage);
/* Port DMAE comes here */
+ bnx2x_init_block(bp, DMAE_BLOCK, init_stage);
switch (XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config)) {
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
break;
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
/* add SPIO 5 to group 0 */
- val = REG_RD(bp, MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0);
+ {
+ u32 reg_addr = (port ? MISC_REG_AEU_ENABLE1_FUNC_1_OUT_0 :
+ MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0);
+ val = REG_RD(bp, reg_addr);
val |= AEU_INPUTS_ATTN_BITS_SPIO5;
- REG_WR(bp, MISC_REG_AEU_ENABLE1_FUNC_0_OUT_0, val);
+ REG_WR(bp, reg_addr, val);
+ }
break;
default:
if (CHIP_IS_E1H(bp)) {
for (i = 0; i < 9; i++)
bnx2x_init_block(bp,
- cm_start[func][i], cm_end[func][i]);
+ cm_blocks[i], FUNC0_STAGE + func);
REG_WR(bp, NIG_REG_LLH0_FUNC_EN + port*8, 1);
REG_WR(bp, NIG_REG_LLH0_FUNC_VLAN_ID + port*8, bp->e1hov);
REG_WR(bp, HC_REG_LEADING_EDGE_0 + port*8, 0);
REG_WR(bp, HC_REG_TRAILING_EDGE_0 + port*8, 0);
}
- bnx2x_init_block(bp, hc_limits[func][0], hc_limits[func][1]);
+ bnx2x_init_block(bp, HC_BLOCK, FUNC0_STAGE + func);
/* Reset PCIE errors for debug */
REG_WR(bp, 0x2114, 0xffffffff);
}
/* send the MCP a request, block until there is a reply */
-static u32 bnx2x_fw_command(struct bnx2x *bp, u32 command)
+u32 bnx2x_fw_command(struct bnx2x *bp, u32 command)
{
int func = BP_FUNC(bp);
u32 seq = ++bp->fw_seq;
static void bnx2x_netif_start(struct bnx2x *bp)
{
- if (atomic_dec_and_test(&bp->intr_sem)) {
+ int intr_sem;
+
+ intr_sem = atomic_dec_and_test(&bp->intr_sem);
+ smp_wmb(); /* Ensure that bp->intr_sem update is SMP-safe */
+
+ if (intr_sem) {
if (netif_running(bp->dev)) {
bnx2x_napi_enable(bp);
bnx2x_int_enable(bp);
for (i = 0; i < MC_HASH_SIZE; i++)
REG_WR(bp, MC_HASH_OFFSET(bp, i), 0);
+
+ REG_WR(bp, MISC_REG_E1HMF_MODE, 0);
}
if (unload_mode == UNLOAD_NORMAL)
reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS;
- else if (bp->flags & NO_WOL_FLAG) {
+ else if (bp->flags & NO_WOL_FLAG)
reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_MCP;
- if (CHIP_IS_E1H(bp))
- REG_WR(bp, MISC_REG_E1HMF_MODE, 0);
- } else if (bp->wol) {
+ else if (bp->wol) {
u32 emac_base = port ? GRCBASE_EMAC1 : GRCBASE_EMAC0;
u8 *mac_addr = bp->dev->dev_addr;
u32 val;
BNX2X_ERR("This driver needs bc_ver %X but found %X,"
" please upgrade BC\n", BNX2X_BC_VER, val);
}
+ bp->link_params.feature_config_flags |=
+ (val >= REQ_BC_VER_4_VRFY_OPT_MDL) ?
+ FEATURE_CONFIG_BC_SUPPORTS_OPT_MDL_VRFY : 0;
if (BP_E1HVN(bp) == 0) {
pci_read_config_word(bp->pdev, bp->pm_cap + PCI_PM_PMC, &pmc);
SUPPORTED_Asym_Pause);
break;
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
+ BNX2X_DEV_INFO("ext_phy_type 0x%x (8727)\n",
+ ext_phy_type);
+
+ bp->port.supported |= (SUPPORTED_10000baseT_Full |
+ SUPPORTED_1000baseT_Full |
+ SUPPORTED_Autoneg |
+ SUPPORTED_FIBRE |
+ SUPPORTED_Pause |
+ SUPPORTED_Asym_Pause);
+ break;
+
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101:
BNX2X_DEV_INFO("ext_phy_type 0x%x (SFX7101)\n",
ext_phy_type);
bp->link_params.ext_phy_config =
SHMEM_RD(bp,
dev_info.port_hw_config[port].external_phy_config);
+ /* BCM8727_NOC => BCM8727 no over current */
+ if (XGXS_EXT_PHY_TYPE(bp->link_params.ext_phy_config) ==
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727_NOC) {
+ bp->link_params.ext_phy_config &=
+ ~PORT_HW_CFG_XGXS_EXT_PHY_TYPE_MASK;
+ bp->link_params.ext_phy_config |=
+ PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727;
+ bp->link_params.feature_config_flags |=
+ FEATURE_CONFIG_BCM8727_NOC;
+ }
+
bp->link_params.speed_cap_mask =
SHMEM_RD(bp,
dev_info.port_hw_config[port].speed_capability_mask);
bp->link_params.xgxs_config_tx[(i << 1) + 1] = (val & 0xffff);
}
- config = SHMEM_RD(bp, dev_info.port_feature_config[port].config);
- if (config & PORT_FEAT_CFG_OPT_MDL_ENFRCMNT_ENABLED)
- bp->link_params.feature_config_flags |=
- FEATURE_CONFIG_MODULE_ENFORCMENT_ENABLED;
- else
- bp->link_params.feature_config_flags &=
- ~FEATURE_CONFIG_MODULE_ENFORCMENT_ENABLED;
-
/* If the device is capable of WoL, set the default state according
* to the HW
*/
+ config = SHMEM_RD(bp, dev_info.port_feature_config[port].config);
bp->wol = (!(bp->flags & NO_WOL_FLAG) &&
(config & PORT_FEATURE_WOL_ENABLED));
bp->link_params.ext_phy_config,
bp->link_params.speed_cap_mask, bp->port.link_config);
- bp->link_params.switch_cfg = (bp->port.link_config &
- PORT_FEATURE_CONNECTED_SWITCH_MASK);
+ bp->link_params.switch_cfg |= (bp->port.link_config &
+ PORT_FEATURE_CONNECTED_SWITCH_MASK);
bnx2x_link_settings_supported(bp, bp->link_params.switch_cfg);
bnx2x_link_settings_requested(bp);
/* Disable interrupt handling until HW is initialized */
atomic_set(&bp->intr_sem, 1);
+ smp_wmb(); /* Ensure that bp->intr_sem update is SMP-safe */
mutex_init(&bp->port.phy_mutex);
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8705:
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8706:
case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8726:
+ case PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM8727:
cmd->port = PORT_FIBRE;
break;
return 0;
}
+static u32
+bnx2x_get_link(struct net_device *dev)
+{
+ struct bnx2x *bp = netdev_priv(dev);
+
+ return bp->link_vars.link_up;
+}
+
static int bnx2x_get_eeprom_len(struct net_device *dev)
{
struct bnx2x *bp = netdev_priv(dev);
struct bnx2x *bp = netdev_priv(dev);
bp->rx_ticks = (u16) coal->rx_coalesce_usecs;
- if (bp->rx_ticks > 3000)
- bp->rx_ticks = 3000;
+ if (bp->rx_ticks > BNX2X_MAX_COALESCE_TOUT)
+ bp->rx_ticks = BNX2X_MAX_COALESCE_TOUT;
bp->tx_ticks = (u16) coal->tx_coalesce_usecs;
- if (bp->tx_ticks > 0x3000)
- bp->tx_ticks = 0x3000;
+ if (bp->tx_ticks > BNX2X_MAX_COALESCE_TOUT)
+ bp->tx_ticks = BNX2X_MAX_COALESCE_TOUT;
if (netif_running(dev))
bnx2x_update_coalesce(bp);
{ XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD00, 4, 0x00000001 },
{ XCM_REG_WU_DA_CNT_CMD00, 4, 0x00000003 },
{ XCM_REG_GLB_DEL_ACK_MAX_CNT_0, 4, 0x000000ff },
- { NIG_REG_EGRESS_MNG0_FIFO, 20, 0xffffffff },
{ NIG_REG_LLH0_T_BIT, 4, 0x00000001 },
-/* 20 */ { NIG_REG_EMAC0_IN_EN, 4, 0x00000001 },
- { NIG_REG_BMAC0_IN_EN, 4, 0x00000001 },
+ { NIG_REG_EMAC0_IN_EN, 4, 0x00000001 },
+/* 20 */ { NIG_REG_BMAC0_IN_EN, 4, 0x00000001 },
{ NIG_REG_XCM0_OUT_EN, 4, 0x00000001 },
{ NIG_REG_BRB0_OUT_EN, 4, 0x00000001 },
{ NIG_REG_LLH0_XCM_MASK, 4, 0x00000007 },
{ NIG_REG_LLH0_DEST_MAC_0_0, 160, 0xffffffff },
{ NIG_REG_LLH0_DEST_IP_0_1, 160, 0xffffffff },
{ NIG_REG_LLH0_IPV4_IPV6_0, 160, 0x00000001 },
-/* 30 */ { NIG_REG_LLH0_DEST_UDP_0, 160, 0x0000ffff },
- { NIG_REG_LLH0_DEST_TCP_0, 160, 0x0000ffff },
+ { NIG_REG_LLH0_DEST_UDP_0, 160, 0x0000ffff },
+/* 30 */ { NIG_REG_LLH0_DEST_TCP_0, 160, 0x0000ffff },
{ NIG_REG_LLH0_VLAN_ID_0, 160, 0x00000fff },
{ NIG_REG_XGXS_SERDES0_MODE_SEL, 4, 0x00000001 },
{ NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0, 4, 0x00000001 },
etest->flags &= ~ETH_TEST_FL_OFFLINE;
if (etest->flags & ETH_TEST_FL_OFFLINE) {
+ int port = BP_PORT(bp);
+ u32 val;
u8 link_up;
+ /* save current value of input enable for TX port IF */
+ val = REG_RD(bp, NIG_REG_EGRESS_UMP0_IN_EN + port*4);
+ /* disable input for TX port IF */
+ REG_WR(bp, NIG_REG_EGRESS_UMP0_IN_EN + port*4, 0);
+
link_up = bp->link_vars.link_up;
bnx2x_nic_unload(bp, UNLOAD_NORMAL);
bnx2x_nic_load(bp, LOAD_DIAG);
etest->flags |= ETH_TEST_FL_FAILED;
bnx2x_nic_unload(bp, UNLOAD_NORMAL);
+
+ /* restore input for TX port IF */
+ REG_WR(bp, NIG_REG_EGRESS_UMP0_IN_EN + port*4, val);
+
bnx2x_nic_load(bp, LOAD_NORMAL);
/* wait until link state is restored */
bnx2x_wait_for_link(bp, link_up);
.get_msglevel = bnx2x_get_msglevel,
.set_msglevel = bnx2x_set_msglevel,
.nway_reset = bnx2x_nway_reset,
- .get_link = ethtool_op_get_link,
+ .get_link = bnx2x_get_link,
.get_eeprom_len = bnx2x_get_eeprom_len,
.get_eeprom = bnx2x_get_eeprom,
.set_eeprom = bnx2x_set_eeprom,
mmiowb();
fp->tx_bd_prod += nbd;
- dev->trans_start = jiffies;
if (unlikely(bnx2x_tx_avail(fp) < MAX_SKB_FRAGS + 3)) {
/* We want bnx2x_tx_int to "see" the updated tx_bd_prod
dev->features |= NETIF_F_HW_CSUM;
if (bp->flags & USING_DAC_FLAG)
dev->features |= NETIF_F_HIGHDMA;
+ dev->features |= (NETIF_F_TSO | NETIF_F_TSO_ECN);
+ dev->features |= NETIF_F_TSO6;
#ifdef BCM_VLAN
dev->features |= (NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX);
bp->flags |= (HW_VLAN_RX_FLAG | HW_VLAN_TX_FLAG);
+
+ dev->vlan_features |= NETIF_F_SG;
+ dev->vlan_features |= NETIF_F_HW_CSUM;
+ if (bp->flags & USING_DAC_FLAG)
+ dev->vlan_features |= NETIF_F_HIGHDMA;
+ dev->vlan_features |= (NETIF_F_TSO | NETIF_F_TSO_ECN);
+ dev->vlan_features |= NETIF_F_TSO6;
#endif
- dev->features |= (NETIF_F_TSO | NETIF_F_TSO_ECN);
- dev->features |= NETIF_F_TSO6;
return 0;
val = (val & PCICFG_LINK_SPEED) >> PCICFG_LINK_SPEED_SHIFT;
return val;
}
+static int __devinit bnx2x_check_firmware(struct bnx2x *bp)
+{
+ struct bnx2x_fw_file_hdr *fw_hdr;
+ struct bnx2x_fw_file_section *sections;
+ u16 *ops_offsets;
+ u32 offset, len, num_ops;
+ int i;
+ const struct firmware *firmware = bp->firmware;
+ const u8 * fw_ver;
+
+ if (firmware->size < sizeof(struct bnx2x_fw_file_hdr))
+ return -EINVAL;
+
+ fw_hdr = (struct bnx2x_fw_file_hdr *)firmware->data;
+ sections = (struct bnx2x_fw_file_section *)fw_hdr;
+
+ /* Make sure none of the offsets and sizes make us read beyond
+ * the end of the firmware data */
+ for (i = 0; i < sizeof(*fw_hdr) / sizeof(*sections); i++) {
+ offset = be32_to_cpu(sections[i].offset);
+ len = be32_to_cpu(sections[i].len);
+ if (offset + len > firmware->size) {
+ printk(KERN_ERR PFX "Section %d length is out of bounds\n", i);
+ return -EINVAL;
+ }
+ }
+
+ /* Likewise for the init_ops offsets */
+ offset = be32_to_cpu(fw_hdr->init_ops_offsets.offset);
+ ops_offsets = (u16 *)(firmware->data + offset);
+ num_ops = be32_to_cpu(fw_hdr->init_ops.len) / sizeof(struct raw_op);
+
+ for (i = 0; i < be32_to_cpu(fw_hdr->init_ops_offsets.len) / 2; i++) {
+ if (be16_to_cpu(ops_offsets[i]) > num_ops) {
+ printk(KERN_ERR PFX "Section offset %d is out of bounds\n", i);
+ return -EINVAL;
+ }
+ }
+
+ /* Check FW version */
+ offset = be32_to_cpu(fw_hdr->fw_version.offset);
+ fw_ver = firmware->data + offset;
+ if ((fw_ver[0] != BCM_5710_FW_MAJOR_VERSION) ||
+ (fw_ver[1] != BCM_5710_FW_MINOR_VERSION) ||
+ (fw_ver[2] != BCM_5710_FW_REVISION_VERSION) ||
+ (fw_ver[3] != BCM_5710_FW_ENGINEERING_VERSION)) {
+ printk(KERN_ERR PFX "Bad FW version:%d.%d.%d.%d."
+ " Should be %d.%d.%d.%d\n",
+ fw_ver[0], fw_ver[1], fw_ver[2],
+ fw_ver[3], BCM_5710_FW_MAJOR_VERSION,
+ BCM_5710_FW_MINOR_VERSION,
+ BCM_5710_FW_REVISION_VERSION,
+ BCM_5710_FW_ENGINEERING_VERSION);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static void inline be32_to_cpu_n(const u8 *_source, u8 *_target, u32 n)
+{
+ u32 i;
+ const __be32 *source = (const __be32*)_source;
+ u32 *target = (u32*)_target;
+
+ for (i = 0; i < n/4; i++)
+ target[i] = be32_to_cpu(source[i]);
+}
+
+/*
+ Ops array is stored in the following format:
+ {op(8bit), offset(24bit, big endian), data(32bit, big endian)}
+ */
+static void inline bnx2x_prep_ops(const u8 *_source, u8 *_target, u32 n)
+{
+ u32 i, j, tmp;
+ const __be32 *source = (const __be32*)_source;
+ struct raw_op *target = (struct raw_op*)_target;
+
+ for (i = 0, j = 0; i < n/8; i++, j+=2) {
+ tmp = be32_to_cpu(source[j]);
+ target[i].op = (tmp >> 24) & 0xff;
+ target[i].offset = tmp & 0xffffff;
+ target[i].raw_data = be32_to_cpu(source[j+1]);
+ }
+}
+static void inline be16_to_cpu_n(const u8 *_source, u8 *_target, u32 n)
+{
+ u32 i;
+ u16 *target = (u16*)_target;
+ const __be16 *source = (const __be16*)_source;
+
+ for (i = 0; i < n/2; i++)
+ target[i] = be16_to_cpu(source[i]);
+}
+
+#define BNX2X_ALLOC_AND_SET(arr, lbl, func) \
+ do { \
+ u32 len = be32_to_cpu(fw_hdr->arr.len); \
+ bp->arr = kmalloc(len, GFP_KERNEL); \
+ if (!bp->arr) { \
+ printk(KERN_ERR PFX "Failed to allocate %d bytes for "#arr"\n", len); \
+ goto lbl; \
+ } \
+ func(bp->firmware->data + \
+ be32_to_cpu(fw_hdr->arr.offset), \
+ (u8*)bp->arr, len); \
+ } while (0)
+
+
+static int __devinit bnx2x_init_firmware(struct bnx2x *bp, struct device *dev)
+{
+ char fw_file_name[40] = {0};
+ int rc, offset;
+ struct bnx2x_fw_file_hdr *fw_hdr;
+
+ /* Create a FW file name */
+ if (CHIP_IS_E1(bp))
+ offset = sprintf(fw_file_name, FW_FILE_PREFIX_E1);
+ else
+ offset = sprintf(fw_file_name, FW_FILE_PREFIX_E1H);
+
+ sprintf(fw_file_name + offset, "%d.%d.%d.%d.fw",
+ BCM_5710_FW_MAJOR_VERSION,
+ BCM_5710_FW_MINOR_VERSION,
+ BCM_5710_FW_REVISION_VERSION,
+ BCM_5710_FW_ENGINEERING_VERSION);
+
+ printk(KERN_INFO PFX "Loading %s\n", fw_file_name);
+
+ rc = request_firmware(&bp->firmware, fw_file_name, dev);
+ if (rc) {
+ printk(KERN_ERR PFX "Can't load firmware file %s\n", fw_file_name);
+ goto request_firmware_exit;
+ }
+
+ rc = bnx2x_check_firmware(bp);
+ if (rc) {
+ printk(KERN_ERR PFX "Corrupt firmware file %s\n", fw_file_name);
+ goto request_firmware_exit;
+ }
+
+ fw_hdr = (struct bnx2x_fw_file_hdr *)bp->firmware->data;
+
+ /* Initialize the pointers to the init arrays */
+ /* Blob */
+ BNX2X_ALLOC_AND_SET(init_data, request_firmware_exit, be32_to_cpu_n);
+
+ /* Opcodes */
+ BNX2X_ALLOC_AND_SET(init_ops, init_ops_alloc_err, bnx2x_prep_ops);
+
+ /* Offsets */
+ BNX2X_ALLOC_AND_SET(init_ops_offsets, init_offsets_alloc_err, be16_to_cpu_n);
+
+ /* STORMs firmware */
+ bp->tsem_int_table_data = bp->firmware->data +
+ be32_to_cpu(fw_hdr->tsem_int_table_data.offset);
+ bp->tsem_pram_data = bp->firmware->data +
+ be32_to_cpu(fw_hdr->tsem_pram_data.offset);
+ bp->usem_int_table_data = bp->firmware->data +
+ be32_to_cpu(fw_hdr->usem_int_table_data.offset);
+ bp->usem_pram_data = bp->firmware->data +
+ be32_to_cpu(fw_hdr->usem_pram_data.offset);
+ bp->xsem_int_table_data = bp->firmware->data +
+ be32_to_cpu(fw_hdr->xsem_int_table_data.offset);
+ bp->xsem_pram_data = bp->firmware->data +
+ be32_to_cpu(fw_hdr->xsem_pram_data.offset);
+ bp->csem_int_table_data = bp->firmware->data +
+ be32_to_cpu(fw_hdr->csem_int_table_data.offset);
+ bp->csem_pram_data = bp->firmware->data +
+ be32_to_cpu(fw_hdr->csem_pram_data.offset);
+
+ return 0;
+init_offsets_alloc_err:
+ kfree(bp->init_ops);
+init_ops_alloc_err:
+ kfree(bp->init_data);
+request_firmware_exit:
+ release_firmware(bp->firmware);
+
+ return rc;
+}
+
+
static int __devinit bnx2x_init_one(struct pci_dev *pdev,
const struct pci_device_id *ent)
if (rc)
goto init_one_exit;
+ /* Set init arrays */
+ rc = bnx2x_init_firmware(bp, &pdev->dev);
+ if (rc) {
+ printk(KERN_ERR PFX "Error loading firmware\n");
+ goto init_one_exit;
+ }
+
rc = register_netdev(dev);
if (rc) {
dev_err(&pdev->dev, "Cannot register net device\n");
unregister_netdev(dev);
+ kfree(bp->init_ops_offsets);
+ kfree(bp->init_ops);
+ kfree(bp->init_data);
+ release_firmware(bp->firmware);
+
if (bp->regview)
iounmap(bp->regview);
static int __init bnx2x_init(void)
{
+ int ret;
+
bnx2x_wq = create_singlethread_workqueue("bnx2x");
if (bnx2x_wq == NULL) {
printk(KERN_ERR PFX "Cannot create workqueue\n");
return -ENOMEM;
}
- return pci_register_driver(&bnx2x_pci_driver);
+ ret = pci_register_driver(&bnx2x_pci_driver);
+ if (ret) {
+ printk(KERN_ERR PFX "Cannot register driver\n");
+ destroy_workqueue(bnx2x_wq);
+ }
+ return ret;
}
static void __exit bnx2x_cleanup(void)
module_init(bnx2x_init);
module_exit(bnx2x_cleanup);
+