(at your option) any later version.
*/
-#define DRV_NAME "D-Link DL2000-based linux driver"
-#define DRV_VERSION "v1.18"
-#define DRV_RELDATE "2006/06/27"
+#define DRV_NAME "DL2000/TC902x-based linux driver"
+#define DRV_VERSION "v1.19"
+#define DRV_RELDATE "2007/08/12"
#include "dl2k.h"
#include <linux/dma-mapping.h>
static int version_printed;
void *ring_space;
dma_addr_t ring_dma;
+ DECLARE_MAC_BUF(mac);
if (!version_printed++)
printk ("%s", version);
err = -ENOMEM;
goto err_out_res;
}
- SET_MODULE_OWNER (dev);
SET_NETDEV_DEV(dev, &pdev->dev);
#ifdef MEM_MAPPING
np->an_enable = 1;
mii_set_media (dev);
}
- pci_read_config_byte(pdev, PCI_REVISION_ID, &np->pci_rev_id);
err = register_netdev (dev);
if (err)
card_idx++;
- printk (KERN_INFO "%s: %s, %02x:%02x:%02x:%02x:%02x:%02x, IRQ %d\n",
- dev->name, np->name,
- dev->dev_addr[0], dev->dev_addr[1], dev->dev_addr[2],
- dev->dev_addr[3], dev->dev_addr[4], dev->dev_addr[5], irq);
+ printk (KERN_INFO "%s: %s, %s, IRQ %d\n",
+ dev->name, np->name, print_mac(mac, dev->dev_addr), irq);
if (tx_coalesce > 1)
printk(KERN_INFO "tx_coalesce:\t%d packets\n",
tx_coalesce);
return err;
}
-int
+static int
find_miiphy (struct net_device *dev)
{
int i, phy_found = 0;
return 0;
}
-int
+static int
parse_eeprom (struct net_device *dev)
{
int i, j;
#ifdef MEM_MAPPING
ioaddr = dev->base_addr;
#endif
- /* Check CRC */
- crc = ~ether_crc_le (256 - 4, sromdata);
- if (psrom->crc != crc) {
- printk (KERN_ERR "%s: EEPROM data CRC error.\n", dev->name);
- return -1;
+ if (np->pdev->vendor == PCI_VENDOR_ID_DLINK) { /* D-Link Only */
+ /* Check CRC */
+ crc = ~ether_crc_le (256 - 4, sromdata);
+ if (psrom->crc != crc) {
+ printk (KERN_ERR "%s: EEPROM data CRC error.\n",
+ dev->name);
+ return -1;
+ }
}
/* Set MAC address */
for (i = 0; i < 6; i++)
dev->dev_addr[i] = psrom->mac_addr[i];
+ if (np->pdev->vendor != PCI_VENDOR_ID_DLINK) {
+ return 0;
+ }
+
/* Parse Software Information Block */
i = 0x30;
psib = (u8 *) sromdata;
break;
}
np->rx_skbuff[entry] = skb;
- skb->dev = dev;
/* 16 byte align the IP header */
skb_reserve (skb, 2);
np->rx_ring[entry].fraginfo =
dev->name);
break;
}
- skb->dev = dev; /* Mark as being used by this device. */
skb_reserve (skb, 2); /* 16 byte align the IP header. */
/* Rubicon now supports 40 bits of addressing space. */
np->rx_ring[i].fraginfo =
DMA_48BIT_MASK,
np->rx_buf_sz,
PCI_DMA_FROMDEVICE);
- skb->dev = dev;
/* 16 byte align the IP header */
skb_reserve (skb, 2);
- eth_copy_and_sum (skb,
+ skb_copy_to_linear_data (skb,
np->rx_skbuff[entry]->data,
- pkt_len, 0);
+ pkt_len);
skb_put (skb, pkt_len);
pci_dma_sync_single_for_device(np->pdev,
desc->fraginfo &
skb->protocol = eth_type_trans (skb, dev);
#if 0
/* Checksum done by hw, but csum value unavailable. */
- if (np->pci_rev_id >= 0x0c &&
+ if (np->pdev->pci_rev_id >= 0x0c &&
!(frame_status & (TCPError | UDPError | IPError))) {
skb->ip_summed = CHECKSUM_UNNECESSARY;
}
break;
}
np->rx_skbuff[entry] = skb;
- skb->dev = dev;
/* 16 byte align the IP header */
skb_reserve (skb, 2);
np->rx_ring[entry].fraginfo =
}
-int
+static int
change_mtu (struct net_device *dev, int new_mtu)
{
struct netdev_private *np = netdev_priv(dev);
#define EEP_BUSY 0x8000
/* Read the EEPROM word */
/* We use I/O instruction to read/write eeprom to avoid fail on some machines */
-int
+static int
read_eeprom (long ioaddr, int eep_addr)
{
int i = 1000;