/* HPSA_DRIVER_VERSION must be 3 byte values (0-255) separated by '.' */
#define HPSA_DRIVER_VERSION "2.0.2-1"
#define DRIVER_NAME "HP HPSA Driver (v " HPSA_DRIVER_VERSION ")"
+#define HPSA "hpsa"
/* How long to wait (in milliseconds) for board to go into simple mode */
#define MAX_CONFIG_WAIT 30000
switch (c->err_info->SenseInfo[12]) {
case STATE_CHANGED:
- dev_warn(&h->pdev->dev, "hpsa%d: a state change "
+ dev_warn(&h->pdev->dev, HPSA "%d: a state change "
"detected, command retried\n", h->ctlr);
break;
case LUN_FAILED:
- dev_warn(&h->pdev->dev, "hpsa%d: LUN failure "
+ dev_warn(&h->pdev->dev, HPSA "%d: LUN failure "
"detected, action required\n", h->ctlr);
break;
case REPORT_LUNS_CHANGED:
- dev_warn(&h->pdev->dev, "hpsa%d: report LUN data "
+ dev_warn(&h->pdev->dev, HPSA "%d: report LUN data "
"changed, action required\n", h->ctlr);
/*
- * Note: this REPORT_LUNS_CHANGED condition only occurs on the MSA2012.
+ * Note: this REPORT_LUNS_CHANGED condition only occurs on the external
+ * target (array) devices.
*/
break;
case POWER_OR_RESET:
- dev_warn(&h->pdev->dev, "hpsa%d: a power on "
+ dev_warn(&h->pdev->dev, HPSA "%d: a power on "
"or device reset detected\n", h->ctlr);
break;
case UNIT_ATTENTION_CLEARED:
- dev_warn(&h->pdev->dev, "hpsa%d: unit attention "
+ dev_warn(&h->pdev->dev, HPSA "%d: unit attention "
"cleared by another initiator\n", h->ctlr);
break;
default:
- dev_warn(&h->pdev->dev, "hpsa%d: unknown "
+ dev_warn(&h->pdev->dev, HPSA "%d: unknown "
"unit attention detected\n", h->ctlr);
break;
}
0x40800E11, /* Smart Array 5i */
0x409C0E11, /* Smart Array 6400 */
0x409D0E11, /* Smart Array 6400 EM */
+ 0x40700E11, /* Smart Array 5300 */
+ 0x40820E11, /* Smart Array 532 */
+ 0x40830E11, /* Smart Array 5312 */
+ 0x409A0E11, /* Smart Array 641 */
+ 0x409B0E11, /* Smart Array 642 */
+ 0x40910E11, /* Smart Array 6i */
};
/* List of controllers which cannot even be soft reset */
static u32 soft_unresettable_controller[] = {
0x40800E11, /* Smart Array 5i */
+ 0x40700E11, /* Smart Array 5300 */
+ 0x40820E11, /* Smart Array 532 */
+ 0x40830E11, /* Smart Array 5312 */
+ 0x409A0E11, /* Smart Array 641 */
+ 0x409B0E11, /* Smart Array 642 */
+ 0x40910E11, /* Smart Array 6i */
/* Exclude 640x boards. These are two pci devices in one slot
* which share a battery backed cache module. One controls the
* cache, the other accesses the cache through the one that controls
static struct scsi_host_template hpsa_driver_template = {
.module = THIS_MODULE,
- .name = "hpsa",
- .proc_name = "hpsa",
+ .name = HPSA,
+ .proc_name = HPSA,
.queuecommand = hpsa_scsi_queue_command,
.scan_start = hpsa_scan_start,
.scan_finished = hpsa_scan_finished,
int i, found = 0;
DECLARE_BITMAP(lun_taken, HPSA_MAX_DEVICES);
- memset(&lun_taken[0], 0, HPSA_MAX_DEVICES >> 3);
+ bitmap_zero(lun_taken, HPSA_MAX_DEVICES);
for (i = 0; i < h->ndevices; i++) {
if (h->dev[i]->bus == bus && h->dev[i]->target != -1)
- set_bit(h->dev[i]->target, lun_taken);
+ __set_bit(h->dev[i]->target, lun_taken);
}
- for (i = 0; i < HPSA_MAX_DEVICES; i++) {
- if (!test_bit(i, lun_taken)) {
- /* *bus = 1; */
- *target = i;
- *lun = 0;
- found = 1;
- break;
- }
+ i = find_first_zero_bit(lun_taken, HPSA_MAX_DEVICES);
+ if (i < HPSA_MAX_DEVICES) {
+ /* *bus = 1; */
+ *target = i;
+ *lun = 0;
+ found = 1;
}
return !found;
}
return 0;
}
+/* Update an entry in h->dev[] array. */
+static void hpsa_scsi_update_entry(struct ctlr_info *h, int hostno,
+ int entry, struct hpsa_scsi_dev_t *new_entry)
+{
+ /* assumes h->devlock is held */
+ BUG_ON(entry < 0 || entry >= HPSA_MAX_DEVICES);
+
+ /* Raid level changed. */
+ h->dev[entry]->raid_level = new_entry->raid_level;
+ dev_info(&h->pdev->dev, "%s device c%db%dt%dl%d updated.\n",
+ scsi_device_type(new_entry->devtype), hostno, new_entry->bus,
+ new_entry->target, new_entry->lun);
+}
+
/* Replace an entry from h->dev[] array. */
static void hpsa_scsi_replace_entry(struct ctlr_info *h, int hostno,
int entry, struct hpsa_scsi_dev_t *new_entry,
return 1;
}
+static inline int device_updated(struct hpsa_scsi_dev_t *dev1,
+ struct hpsa_scsi_dev_t *dev2)
+{
+ /* Device attributes that can change, but don't mean
+ * that the device is a different device, nor that the OS
+ * needs to be told anything about the change.
+ */
+ if (dev1->raid_level != dev2->raid_level)
+ return 1;
+ return 0;
+}
+
/* Find needle in haystack. If exact match found, return DEVICE_SAME,
* and return needle location in *index. If scsi3addr matches, but not
* vendor, model, serial num, etc. return DEVICE_CHANGED, and return needle
- * location in *index. If needle not found, return DEVICE_NOT_FOUND.
+ * location in *index.
+ * In the case of a minor device attribute change, such as RAID level, just
+ * return DEVICE_UPDATED, along with the updated device's location in index.
+ * If needle not found, return DEVICE_NOT_FOUND.
*/
static int hpsa_scsi_find_entry(struct hpsa_scsi_dev_t *needle,
struct hpsa_scsi_dev_t *haystack[], int haystack_size,
#define DEVICE_NOT_FOUND 0
#define DEVICE_CHANGED 1
#define DEVICE_SAME 2
+#define DEVICE_UPDATED 3
for (i = 0; i < haystack_size; i++) {
if (haystack[i] == NULL) /* previously removed. */
continue;
if (SCSI3ADDR_EQ(needle->scsi3addr, haystack[i]->scsi3addr)) {
*index = i;
- if (device_is_the_same(needle, haystack[i]))
+ if (device_is_the_same(needle, haystack[i])) {
+ if (device_updated(needle, haystack[i]))
+ return DEVICE_UPDATED;
return DEVICE_SAME;
- else
+ } else {
return DEVICE_CHANGED;
+ }
}
}
*index = -1;
* sd[] and remove them from h->dev[], and for any
* devices which have changed, remove the old device
* info and add the new device info.
+ * If minor device attributes change, just update
+ * the existing device structure.
*/
i = 0;
nremoved = 0;
* at the bottom of hpsa_update_scsi_devices()
*/
sd[entry] = NULL;
+ } else if (device_change == DEVICE_UPDATED) {
+ hpsa_scsi_update_entry(h, hostno, i, sd[entry]);
}
i++;
}
cmd_free(h, cp);
}
-static int hpsa_scsi_detect(struct ctlr_info *h)
-{
- struct Scsi_Host *sh;
- int error;
-
- sh = scsi_host_alloc(&hpsa_driver_template, sizeof(h));
- if (sh == NULL)
- goto fail;
-
- sh->io_port = 0;
- sh->n_io_port = 0;
- sh->this_id = -1;
- sh->max_channel = 3;
- sh->max_cmd_len = MAX_COMMAND_SIZE;
- sh->max_lun = HPSA_MAX_LUN;
- sh->max_id = HPSA_MAX_LUN;
- sh->can_queue = h->nr_cmds;
- sh->cmd_per_lun = h->nr_cmds;
- sh->sg_tablesize = h->maxsgentries;
- h->scsi_host = sh;
- sh->hostdata[0] = (unsigned long) h;
- sh->irq = h->intr[h->intr_mode];
- sh->unique_id = sh->irq;
- error = scsi_add_host(sh, &h->pdev->dev);
- if (error)
- goto fail_host_put;
- scsi_scan_host(sh);
- return 0;
-
- fail_host_put:
- dev_err(&h->pdev->dev, "hpsa_scsi_detect: scsi_add_host"
- " failed for controller %d\n", h->ctlr);
- scsi_host_put(sh);
- return error;
- fail:
- dev_err(&h->pdev->dev, "hpsa_scsi_detect: scsi_host_alloc"
- " failed for controller %d\n", h->ctlr);
- return -ENOMEM;
-}
-
static void hpsa_pci_unmap(struct pci_dev *pdev,
struct CommandList *c, int sg_used, int data_direction)
{
return 1;
}
-static unsigned char *msa2xxx_model[] = {
+static unsigned char *ext_target_model[] = {
"MSA2012",
"MSA2024",
"MSA2312",
NULL,
};
-static int is_msa2xxx(struct ctlr_info *h, struct hpsa_scsi_dev_t *device)
+static int is_ext_target(struct ctlr_info *h, struct hpsa_scsi_dev_t *device)
{
int i;
- for (i = 0; msa2xxx_model[i]; i++)
- if (strncmp(device->model, msa2xxx_model[i],
- strlen(msa2xxx_model[i])) == 0)
+ for (i = 0; ext_target_model[i]; i++)
+ if (strncmp(device->model, ext_target_model[i],
+ strlen(ext_target_model[i])) == 0)
return 1;
return 0;
}
/* Helper function to assign bus, target, lun mapping of devices.
- * Puts non-msa2xxx logical volumes on bus 0, msa2xxx logical
+ * Puts non-external target logical volumes on bus 0, external target logical
* volumes on bus 1, physical devices on bus 2. and the hba on bus 3.
* Logical drive target and lun are assigned at this time, but
* physical device lun and target assignment are deferred (assigned
* in hpsa_find_target_lun, called by hpsa_scsi_add_entry.)
*/
static void figure_bus_target_lun(struct ctlr_info *h,
- u8 *lunaddrbytes, int *bus, int *target, int *lun,
- struct hpsa_scsi_dev_t *device)
+ u8 *lunaddrbytes, struct hpsa_scsi_dev_t *device)
{
- u32 lunid;
+ u32 lunid = le32_to_cpu(*((__le32 *) lunaddrbytes));
- if (is_logical_dev_addr_mode(lunaddrbytes)) {
- /* logical device */
- if (unlikely(is_scsi_rev_5(h))) {
- /* p1210m, logical drives lun assignments
- * match SCSI REPORT LUNS data.
- */
- lunid = le32_to_cpu(*((__le32 *) lunaddrbytes));
- *bus = 0;
- *target = 0;
- *lun = (lunid & 0x3fff) + 1;
- } else {
- /* not p1210m... */
- lunid = le32_to_cpu(*((__le32 *) lunaddrbytes));
- if (is_msa2xxx(h, device)) {
- /* msa2xxx way, put logicals on bus 1
- * and match target/lun numbers box
- * reports.
- */
- *bus = 1;
- *target = (lunid >> 16) & 0x3fff;
- *lun = lunid & 0x00ff;
- } else {
- /* Traditional smart array way. */
- *bus = 0;
- *lun = 0;
- *target = lunid & 0x3fff;
- }
- }
- } else {
- /* physical device */
+ if (!is_logical_dev_addr_mode(lunaddrbytes)) {
+ /* physical device, target and lun filled in later */
if (is_hba_lunid(lunaddrbytes))
- if (unlikely(is_scsi_rev_5(h))) {
- *bus = 0; /* put p1210m ctlr at 0,0,0 */
- *target = 0;
- *lun = 0;
- return;
- } else
- *bus = 3; /* traditional smartarray */
+ hpsa_set_bus_target_lun(device, 3, 0, lunid & 0x3fff);
else
- *bus = 2; /* physical disk */
- *target = -1;
- *lun = -1; /* we will fill these in later. */
+ /* defer target, lun assignment for physical devices */
+ hpsa_set_bus_target_lun(device, 2, -1, -1);
+ return;
+ }
+ /* It's a logical device */
+ if (is_ext_target(h, device)) {
+ /* external target way, put logicals on bus 1
+ * and match target/lun numbers box
+ * reports, other smart array, bus 0, target 0, match lunid
+ */
+ hpsa_set_bus_target_lun(device,
+ 1, (lunid >> 16) & 0x3fff, lunid & 0x00ff);
+ return;
}
+ hpsa_set_bus_target_lun(device, 0, 0, lunid & 0x3fff);
}
/*
* If there is no lun 0 on a target, linux won't find any devices.
- * For the MSA2xxx boxes, we have to manually detect the enclosure
+ * For the external targets (arrays), we have to manually detect the enclosure
* which is at lun zero, as CCISS_REPORT_PHYSICAL_LUNS doesn't report
* it for some reason. *tmpdevice is the target we're adding,
* this_device is a pointer into the current element of currentsd[]
* lun 0 assigned.
* Returns 1 if an enclosure was added, 0 if not.
*/
-static int add_msa2xxx_enclosure_device(struct ctlr_info *h,
+static int add_ext_target_dev(struct ctlr_info *h,
struct hpsa_scsi_dev_t *tmpdevice,
struct hpsa_scsi_dev_t *this_device, u8 *lunaddrbytes,
- int bus, int target, int lun, unsigned long lunzerobits[],
- int *nmsa2xxx_enclosures)
+ unsigned long lunzerobits[], int *n_ext_target_devs)
{
unsigned char scsi3addr[8];
- if (test_bit(target, lunzerobits))
+ if (test_bit(tmpdevice->target, lunzerobits))
return 0; /* There is already a lun 0 on this target. */
if (!is_logical_dev_addr_mode(lunaddrbytes))
return 0; /* It's the logical targets that may lack lun 0. */
- if (!is_msa2xxx(h, tmpdevice))
- return 0; /* It's only the MSA2xxx that have this problem. */
+ if (!is_ext_target(h, tmpdevice))
+ return 0; /* Only external target devices have this problem. */
- if (lun == 0) /* if lun is 0, then obviously we have a lun 0. */
+ if (tmpdevice->lun == 0) /* if lun is 0, then we have a lun 0. */
return 0;
memset(scsi3addr, 0, 8);
- scsi3addr[3] = target;
+ scsi3addr[3] = tmpdevice->target;
if (is_hba_lunid(scsi3addr))
return 0; /* Don't add the RAID controller here. */
if (is_scsi_rev_5(h))
return 0; /* p1210m doesn't need to do this. */
- if (*nmsa2xxx_enclosures >= MAX_MSA2XXX_ENCLOSURES) {
- dev_warn(&h->pdev->dev, "Maximum number of MSA2XXX "
- "enclosures exceeded. Check your hardware "
+ if (*n_ext_target_devs >= MAX_EXT_TARGETS) {
+ dev_warn(&h->pdev->dev, "Maximum number of external "
+ "target devices exceeded. Check your hardware "
"configuration.");
return 0;
}
if (hpsa_update_device_info(h, scsi3addr, this_device, NULL))
return 0;
- (*nmsa2xxx_enclosures)++;
- hpsa_set_bus_target_lun(this_device, bus, target, 0);
- set_bit(target, lunzerobits);
+ (*n_ext_target_devs)++;
+ hpsa_set_bus_target_lun(this_device,
+ tmpdevice->bus, tmpdevice->target, 0);
+ set_bit(tmpdevice->target, lunzerobits);
return 1;
}
struct hpsa_scsi_dev_t **currentsd, *this_device, *tmpdevice;
int ncurrent = 0;
int reportlunsize = sizeof(*physdev_list) + HPSA_MAX_PHYS_LUN * 8;
- int i, nmsa2xxx_enclosures, ndevs_to_allocate;
- int bus, target, lun;
+ int i, n_ext_target_devs, ndevs_to_allocate;
int raid_ctlr_position;
- DECLARE_BITMAP(lunzerobits, HPSA_MAX_TARGETS_PER_CTLR);
+ DECLARE_BITMAP(lunzerobits, MAX_EXT_TARGETS);
currentsd = kzalloc(sizeof(*currentsd) * HPSA_MAX_DEVICES, GFP_KERNEL);
physdev_list = kzalloc(reportlunsize, GFP_KERNEL);
logdev_list, &nlogicals))
goto out;
- /* We might see up to 32 MSA2xxx enclosures, actually 8 of them
- * but each of them 4 times through different paths. The plus 1
- * is for the RAID controller.
+ /* We might see up to the maximum number of logical and physical disks
+ * plus external target devices, and a device for the local RAID
+ * controller.
*/
- ndevs_to_allocate = nphysicals + nlogicals + MAX_MSA2XXX_ENCLOSURES + 1;
+ ndevs_to_allocate = nphysicals + nlogicals + MAX_EXT_TARGETS + 1;
/* Allocate the per device structures */
for (i = 0; i < ndevs_to_allocate; i++) {
raid_ctlr_position = nphysicals + nlogicals;
/* adjust our table of devices */
- nmsa2xxx_enclosures = 0;
+ n_ext_target_devs = 0;
for (i = 0; i < nphysicals + nlogicals + 1; i++) {
u8 *lunaddrbytes, is_OBDR = 0;
if (hpsa_update_device_info(h, lunaddrbytes, tmpdevice,
&is_OBDR))
continue; /* skip it if we can't talk to it. */
- figure_bus_target_lun(h, lunaddrbytes, &bus, &target, &lun,
- tmpdevice);
+ figure_bus_target_lun(h, lunaddrbytes, tmpdevice);
this_device = currentsd[ncurrent];
/*
- * For the msa2xxx boxes, we have to insert a LUN 0 which
+ * For external target devices, we have to insert a LUN 0 which
* doesn't show up in CCISS_REPORT_PHYSICAL data, but there
* is nonetheless an enclosure device there. We have to
* present that otherwise linux won't find anything if
* there is no lun 0.
*/
- if (add_msa2xxx_enclosure_device(h, tmpdevice, this_device,
- lunaddrbytes, bus, target, lun, lunzerobits,
- &nmsa2xxx_enclosures)) {
+ if (add_ext_target_dev(h, tmpdevice, this_device,
+ lunaddrbytes, lunzerobits,
+ &n_ext_target_devs)) {
ncurrent++;
this_device = currentsd[ncurrent];
}
*this_device = *tmpdevice;
- hpsa_set_bus_target_lun(this_device, bus, target, lun);
switch (this_device->devtype) {
case TYPE_ROM:
static int hpsa_register_scsi(struct ctlr_info *h)
{
- int rc;
+ struct Scsi_Host *sh;
+ int error;
- rc = hpsa_scsi_detect(h);
- if (rc != 0)
- dev_err(&h->pdev->dev, "hpsa_register_scsi: failed"
- " hpsa_scsi_detect(), rc is %d\n", rc);
- return rc;
+ sh = scsi_host_alloc(&hpsa_driver_template, sizeof(h));
+ if (sh == NULL)
+ goto fail;
+
+ sh->io_port = 0;
+ sh->n_io_port = 0;
+ sh->this_id = -1;
+ sh->max_channel = 3;
+ sh->max_cmd_len = MAX_COMMAND_SIZE;
+ sh->max_lun = HPSA_MAX_LUN;
+ sh->max_id = HPSA_MAX_LUN;
+ sh->can_queue = h->nr_cmds;
+ sh->cmd_per_lun = h->nr_cmds;
+ sh->sg_tablesize = h->maxsgentries;
+ h->scsi_host = sh;
+ sh->hostdata[0] = (unsigned long) h;
+ sh->irq = h->intr[h->intr_mode];
+ sh->unique_id = sh->irq;
+ error = scsi_add_host(sh, &h->pdev->dev);
+ if (error)
+ goto fail_host_put;
+ scsi_scan_host(sh);
+ return 0;
+
+ fail_host_put:
+ dev_err(&h->pdev->dev, "%s: scsi_add_host"
+ " failed for controller %d\n", __func__, h->ctlr);
+ scsi_host_put(sh);
+ return error;
+ fail:
+ dev_err(&h->pdev->dev, "%s: scsi_host_alloc"
+ " failed for controller %d\n", __func__, h->ctlr);
+ return -ENOMEM;
}
static int wait_for_device_to_become_ready(struct ctlr_info *h,
status = -EINVAL;
goto cleanup1;
}
- if (ioc->buf_size > ioc->malloc_size * MAXSGENTRIES) {
+ if (ioc->buf_size > ioc->malloc_size * SG_ENTRIES_IN_CMD) {
status = -EINVAL;
goto cleanup1;
}
- buff = kzalloc(MAXSGENTRIES * sizeof(char *), GFP_KERNEL);
+ buff = kzalloc(SG_ENTRIES_IN_CMD * sizeof(char *), GFP_KERNEL);
if (!buff) {
status = -ENOMEM;
goto cleanup1;
}
- buff_size = kmalloc(MAXSGENTRIES * sizeof(int), GFP_KERNEL);
+ buff_size = kmalloc(SG_ENTRIES_IN_CMD * sizeof(int), GFP_KERNEL);
if (!buff_size) {
status = -ENOMEM;
goto cleanup1;
static __devinit void init_driver_version(char *driver_version, int len)
{
memset(driver_version, 0, len);
- strncpy(driver_version, "hpsa " HPSA_DRIVER_VERSION, len - 1);
+ strncpy(driver_version, HPSA " " HPSA_DRIVER_VERSION, len - 1);
}
static __devinit int write_driver_ver_to_cfgtable(
return err;
}
- err = pci_request_regions(h->pdev, "hpsa");
+ err = pci_request_regions(h->pdev, HPSA);
if (err) {
dev_err(&h->pdev->dev,
"cannot obtain PCI resources, aborting\n");
spin_lock_init(&lockup_detector_lock);
hpsa_lockup_detector =
kthread_run(detect_controller_lockup_thread,
- NULL, "hpsa");
+ NULL, HPSA);
}
if (!hpsa_lockup_detector) {
dev_warn(&h->pdev->dev,
if (rc != 0)
goto clean1;
- sprintf(h->devname, "hpsa%d", number_of_controllers);
+ sprintf(h->devname, HPSA "%d", number_of_controllers);
h->ctlr = number_of_controllers;
number_of_controllers++;
#endif /* CONFIG_PCI_MSI */
}
+static void __devexit hpsa_free_device_info(struct ctlr_info *h)
+{
+ int i;
+
+ for (i = 0; i < h->ndevices; i++)
+ kfree(h->dev[i]);
+}
+
static void __devexit hpsa_remove_one(struct pci_dev *pdev)
{
struct ctlr_info *h;
iounmap(h->vaddr);
iounmap(h->transtable);
iounmap(h->cfgtable);
+ hpsa_free_device_info(h);
hpsa_free_sg_chain_blocks(h);
pci_free_consistent(h->pdev,
h->nr_cmds * sizeof(struct CommandList),
}
static struct pci_driver hpsa_pci_driver = {
- .name = "hpsa",
+ .name = HPSA,
.probe = hpsa_init_one,
.remove = __devexit_p(hpsa_remove_one),
.id_table = hpsa_pci_device_id, /* id_table */
* Each SG entry requires 16 bytes. The eight registers are programmed
* with the number of 16-byte blocks a command of that size requires.
* The smallest command possible requires 5 such 16 byte blocks.
- * the largest command possible requires MAXSGENTRIES + 4 16-byte
+ * the largest command possible requires SG_ENTRIES_IN_CMD + 4 16-byte
* blocks. Note, this only extends to the SG entries contained
* within the command block, and does not extend to chained blocks
* of SG elements. bft[] contains the eight values we write to
* the registers. They are not evenly distributed, but have more
* sizes for small commands, and fewer sizes for larger commands.
*/
- int bft[8] = {5, 6, 8, 10, 12, 20, 28, MAXSGENTRIES + 4};
- BUILD_BUG_ON(28 > MAXSGENTRIES + 4);
+ int bft[8] = {5, 6, 8, 10, 12, 20, 28, SG_ENTRIES_IN_CMD + 4};
+ BUILD_BUG_ON(28 > SG_ENTRIES_IN_CMD + 4);
/* 5 = 1 s/g entry or 4k
* 6 = 2 s/g entry or 8k
* 8 = 4 s/g entry or 16k
memset(h->reply_pool, 0, h->reply_pool_size);
h->reply_pool_head = h->reply_pool;
- bft[7] = h->max_sg_entries + 4;
- calc_bucket_map(bft, ARRAY_SIZE(bft), 32, h->blockFetchTable);
+ bft[7] = SG_ENTRIES_IN_CMD + 4;
+ calc_bucket_map(bft, ARRAY_SIZE(bft),
+ SG_ENTRIES_IN_CMD, h->blockFetchTable);
for (i = 0; i < 8; i++)
writel(bft[i], &h->transtable->BlockFetch[i]);
return;
hpsa_get_max_perf_mode_cmds(h);
- h->max_sg_entries = 32;
/* Performant mode ring buffer and supporting data structures */
h->reply_pool_size = h->max_commands * sizeof(u64);
h->reply_pool = pci_alloc_consistent(h->pdev, h->reply_pool_size,
&(h->reply_pool_dhandle));
/* Need a block fetch table for performant mode */
- h->blockFetchTable = kmalloc(((h->max_sg_entries+1) *
+ h->blockFetchTable = kmalloc(((SG_ENTRIES_IN_CMD + 1) *
sizeof(u32)), GFP_KERNEL);
if ((h->reply_pool == NULL)
projects / cascardo / linux.git / blobdiff