memcpy(mgmt->da, da, ETH_ALEN);
memcpy(mgmt->sa, sdata->vif.addr, ETH_ALEN);
if (sdata->vif.type == NL80211_IFTYPE_AP ||
- sdata->vif.type == NL80211_IFTYPE_AP_VLAN)
+ sdata->vif.type == NL80211_IFTYPE_AP_VLAN ||
+ sdata->vif.type == NL80211_IFTYPE_MESH_POINT)
memcpy(mgmt->bssid, sdata->vif.addr, ETH_ALEN);
else if (sdata->vif.type == NL80211_IFTYPE_STATION)
memcpy(mgmt->bssid, sdata->u.mgd.bssid, ETH_ALEN);
+ else if (sdata->vif.type == NL80211_IFTYPE_ADHOC)
+ memcpy(mgmt->bssid, sdata->u.ibss.bssid, ETH_ALEN);
mgmt->frame_control = cpu_to_le16(IEEE80211_FTYPE_MGMT |
IEEE80211_STYPE_ACTION);
return -ENOENT;
}
+ /* if we're already stopping ignore any new requests to stop */
+ if (test_bit(HT_AGG_STATE_STOPPING, &tid_tx->state)) {
+ spin_unlock_bh(&sta->lock);
+ return -EALREADY;
+ }
+
if (test_bit(HT_AGG_STATE_WANT_START, &tid_tx->state)) {
/* not even started yet! */
ieee80211_assign_tid_tx(sta, tid, NULL);
return 0;
}
+ set_bit(HT_AGG_STATE_STOPPING, &tid_tx->state);
+
spin_unlock_bh(&sta->lock);
#ifdef CONFIG_MAC80211_HT_DEBUG
sta->sta.addr, tid);
#endif /* CONFIG_MAC80211_HT_DEBUG */
- set_bit(HT_AGG_STATE_STOPPING, &tid_tx->state);
-
del_timer_sync(&tid_tx->addba_resp_timer);
+ del_timer_sync(&tid_tx->session_timer);
/*
* After this packets are no longer handed right through
*/
clear_bit(HT_AGG_STATE_OPERATIONAL, &tid_tx->state);
+ /*
+ * There might be a few packets being processed right now (on
+ * another CPU) that have already gotten past the aggregation
+ * check when it was still OPERATIONAL and consequently have
+ * IEEE80211_TX_CTL_AMPDU set. In that case, this code might
+ * call into the driver at the same time or even before the
+ * TX paths calls into it, which could confuse the driver.
+ *
+ * Wait for all currently running TX paths to finish before
+ * telling the driver. New packets will not go through since
+ * the aggregation session is no longer OPERATIONAL.
+ */
+ synchronize_net();
+
tid_tx->stop_initiator = initiator;
tid_tx->tx_stop = tx;
tid_tx->timeout);
}
+/*
+ * After accepting the AddBA Response we activated a timer,
+ * resetting it after each frame that we send.
+ */
+static void sta_tx_agg_session_timer_expired(unsigned long data)
+{
+ /* not an elegant detour, but there is no choice as the timer passes
+ * only one argument, and various sta_info are needed here, so init
+ * flow in sta_info_create gives the TID as data, while the timer_to_id
+ * array gives the sta through container_of */
+ u8 *ptid = (u8 *)data;
+ u8 *timer_to_id = ptid - *ptid;
+ struct sta_info *sta = container_of(timer_to_id, struct sta_info,
+ timer_to_tid[0]);
+
+#ifdef CONFIG_MAC80211_HT_DEBUG
+ printk(KERN_DEBUG "tx session timer expired on tid %d\n", (u16)*ptid);
+#endif
+
+ ieee80211_stop_tx_ba_session(&sta->sta, *ptid);
+}
+
int ieee80211_start_tx_ba_session(struct ieee80211_sta *pubsta, u16 tid,
u16 timeout)
{
pubsta->addr, tid);
#endif /* CONFIG_MAC80211_HT_DEBUG */
- /*
- * The aggregation code is not prepared to handle
- * anything but STA/AP due to the BSSID handling.
- * IBSS could work in the code but isn't supported
- * by drivers or the standard.
- */
if (sdata->vif.type != NL80211_IFTYPE_STATION &&
+ sdata->vif.type != NL80211_IFTYPE_MESH_POINT &&
sdata->vif.type != NL80211_IFTYPE_AP_VLAN &&
- sdata->vif.type != NL80211_IFTYPE_AP)
+ sdata->vif.type != NL80211_IFTYPE_AP &&
+ sdata->vif.type != NL80211_IFTYPE_ADHOC)
return -EINVAL;
if (test_sta_flag(sta, WLAN_STA_BLOCK_BA)) {
return -EINVAL;
}
+ /*
+ * 802.11n-2009 11.5.1.1: If the initiating STA is an HT STA, is a
+ * member of an IBSS, and has no other existing Block Ack agreement
+ * with the recipient STA, then the initiating STA shall transmit a
+ * Probe Request frame to the recipient STA and shall not transmit an
+ * ADDBA Request frame unless it receives a Probe Response frame
+ * from the recipient within dot11ADDBAFailureTimeout.
+ *
+ * The probe request mechanism for ADDBA is currently not implemented,
+ * but we only build up Block Ack session with HT STAs. This information
+ * is set when we receive a bss info from a probe response or a beacon.
+ */
+ if (sta->sdata->vif.type == NL80211_IFTYPE_ADHOC &&
+ !sta->sta.ht_cap.ht_supported) {
+#ifdef CONFIG_MAC80211_HT_DEBUG
+ printk(KERN_DEBUG "BA request denied - IBSS STA %pM"
+ "does not advertise HT support\n", pubsta->addr);
+#endif /* CONFIG_MAC80211_HT_DEBUG */
+ return -EINVAL;
+ }
+
spin_lock_bh(&sta->lock);
/* we have tried too many times, receiver does not want A-MPDU */
tid_tx->timeout = timeout;
- /* Tx timer */
+ /* response timer */
tid_tx->addba_resp_timer.function = sta_addba_resp_timer_expired;
tid_tx->addba_resp_timer.data = (unsigned long)&sta->timer_to_tid[tid];
init_timer(&tid_tx->addba_resp_timer);
+ /* tx timer */
+ tid_tx->session_timer.function = sta_tx_agg_session_timer_expired;
+ tid_tx->session_timer.data = (unsigned long)&sta->timer_to_tid[tid];
+ init_timer(&tid_tx->session_timer);
+
/* assign a dialog token */
sta->ampdu_mlme.dialog_token_allocator++;
tid_tx->dialog_token = sta->ampdu_mlme.dialog_token_allocator;
}
mutex_lock(&local->sta_mtx);
- sta = sta_info_get(sdata, ra);
+ sta = sta_info_get_bss(sdata, ra);
if (!sta) {
mutex_unlock(&local->sta_mtx);
#ifdef CONFIG_MAC80211_HT_DEBUG
mutex_lock(&local->sta_mtx);
- sta = sta_info_get(sdata, ra);
+ sta = sta_info_get_bss(sdata, ra);
if (!sta) {
#ifdef CONFIG_MAC80211_HT_DEBUG
printk(KERN_DEBUG "Could not find station: %pM\n", ra);
goto out;
}
- del_timer(&tid_tx->addba_resp_timer);
+ del_timer_sync(&tid_tx->addba_resp_timer);
#ifdef CONFIG_MAC80211_HT_DEBUG
printk(KERN_DEBUG "switched off addBA timer for tid %d\n", tid);
#endif
+
+ /*
+ * addba_resp_timer may have fired before we got here, and
+ * caused WANT_STOP to be set. If the stop then was already
+ * processed further, STOPPING might be set.
+ */
+ if (test_bit(HT_AGG_STATE_WANT_STOP, &tid_tx->state) ||
+ test_bit(HT_AGG_STATE_STOPPING, &tid_tx->state)) {
+#ifdef CONFIG_MAC80211_HT_DEBUG
+ printk(KERN_DEBUG
+ "got addBA resp for tid %d but we already gave up\n",
+ tid);
+#endif
+ goto out;
+ }
+
/*
* IEEE 802.11-2007 7.3.1.14:
* In an ADDBA Response frame, when the Status Code field
ieee80211_agg_tx_operational(local, sta, tid);
sta->ampdu_mlme.addba_req_num[tid] = 0;
+
+ if (tid_tx->timeout)
+ mod_timer(&tid_tx->session_timer,
+ TU_TO_EXP_TIME(tid_tx->timeout));
+
} else {
___ieee80211_stop_tx_ba_session(sta, tid, WLAN_BACK_INITIATOR,
true);