messages received. Unlike other \fBovs\-ofctl\fR commands, if
\fIswitch\fR is the name of a bridge, then the \fBsnoop\fR command
connects to a Unix domain socket named
-\fB@RUNDIR@/\fIbridge\fB.snoop\fR. \fBovs\-vswitchd\fR listens on
+\fB@RUNDIR@/\fIswitch\fB.snoop\fR. \fBovs\-vswitchd\fR listens on
such a socket for each bridge and sends to it all of the OpenFlow
messages sent to or received from its configured OpenFlow controller.
Thus, this command can be used to view OpenFlow protocol activity
corresponding bit in \fItunnel-id\fR must match exactly, and a 0-bit
wildcards that bit.
.
+.IP \fBtun_flags=\fIflags\fR
+Matches flags indicating various aspects of the tunnel encapsulation. Currently,
+there is only one flag defined:
+.IP
+\fBoam\fR: The tunnel protocol indicated that this is an OAM control packet.
+.IP
+Flags can be prefixed by \fB+\fR or \fB-\fR to indicate that the flag should
+be matched as either present or not present, respectively. In addition, flags
+can be specified without a prefix and separated by \fB|\fR to indicate an exact
+match.
+.IP
+Note that it is possible for newer version of Open vSwitch to introduce
+additional flags with varying meaning. It is therefore not recommended to use
+an exact match on this field since the behavior of these new flags is unknown
+and should be ignored.
+.IP
+For non-tunneled packets, the value is 0.
+.IP
+This field was introduced in Open vSwitch 2.5.
+.
.IP \fBtun_src=\fIip\fR[\fB/\fInetmask\fR]
.IQ \fBtun_dst=\fIip\fR[\fB/\fInetmask\fR]
Matches tunnel IPv4 source (or destination) address \fIip\fR. Only packets
\fIdst\fB[\fIstart\fB..\fIend\fB]\fR, which must be an NXM field as
described above.
.IP
-Currently, \fIfields\fR must be either \fBeth_src\fR or
-\fBsymmetric_l4\fR and \fIalgorithm\fR must be one of \fBmodulo_n\fR,
+\fIfields\fR must be one of the following:
+.RS
+.IP \fBeth_src\fR
+Hashes Ethernet source address only.
+.IP \fBsymmetric_l4\fR
+Hashes Ethernet source, destination, and type, VLAN ID, IPv4/IPv6
+source, destination, and protocol, and TCP or SCTP (but not UDP)
+ports. The hash is computed so that pairs of corresponding flows in
+each direction hash to the same value, in environments where L2 paths
+are the same in each direction. UDP ports are not included in the
+hash to support protocols such as VXLAN that use asymmetric ports in
+each direction.
+.IP \fBsymmetric_l3l4\fR
+Hashes IPv4/IPv6 source, destination, and protocol, and TCP or SCTP
+(but not UDP) ports. Like \fBsymmetric_l4\fR, this is a symmetric
+hash, but by excluding L2 headers it is more effective in environments
+with asymmetric L2 paths (e.g. paths involving VRRP IP addresses on a
+router). Not an effective hash function for protocols other than IPv4
+and IPv6, which hash to a constant zero.
+.IP \fBsymmetric_l3l4+udp\fR
+Like \fBsymmetric_l3l4+udp\fR, but UDP ports are included in the hash.
+This is a more effective hash when asymmetric UDP protocols such as
+VXLAN are not a consideration.
+.RE
+.IP
+\fIalgorithm\fR must be one of \fBmodulo_n\fR,
\fBhash_threshold\fR, \fBhrw\fR, and \fBiter_hash\fR. Only
the \fBiter_hash\fR algorithm uses \fIarg\fR.
.IP
\fIslave_type\fR is \fBofport\fR. Thus, each \fIs1\fR through \fIsN\fR should
be an OpenFlow port number. Outputs to the selected slave.
.IP
-Currently, \fIfields\fR must be either \fBeth_src\fR or \fBsymmetric_l4\fR and
-\fIalgorithm\fR must be one of \fBhrw\fR and \fBactive_backup\fR.
+Currently, \fIfields\fR must be either \fBeth_src\fR, \fBsymmetric_l4\fR, \fBsymmetric_l3l4\fR, or \fBsymmetric_l3l4+udp\fR,
+and \fIalgorithm\fR must be one of \fBhrw\fR and \fBactive_backup\fR.
.IP
Example: \fBbundle(eth_src,0,hrw,ofport,slaves:4,8)\fR uses an Ethernet source
hash with basis 0, to select between OpenFlow ports 4 and 8 using the Highest
projects / cascardo / ovs.git / blobdiff