\fIport\fR is omitted, then statistics are printed for \fIqueue\fR on
every port where it exists.
.
+.IP "\fBqueue\-get\-config \fIswitch [\fIport \fR[\fIqueue\fR]]"
+Prints to the console the configuration of \fIqueue\fR on \fIport\fR
+in \fIswitch\fR. If \fIport\fR is omitted or \fBANY\fR, reports
+queues for all port. If \fIqueue\fR is omitted or \fBANY\fR, reports
+all queues. For OpenFlow 1.3 and earlier, the output always includes
+all queues, ignoring \fIqueue\fR if specified.
+.IP
+This command has limited usefulness, because ports often have no
+configured queues and because the OpenFlow protocol provides only very
+limited information about the configuration of a queue.
+.
.SS "OpenFlow 1.1+ Group Table Commands"
.
The following commands work only with switches that support OpenFlow
configuration'' message at connection setup time that requests
\fBINVALID_TTL_TO_CONTROLLER\fR, so that \fBovs\-ofctl monitor\fR can
receive ``packet-in'' messages when TTL reaches zero on \fBdec_ttl\fR action.
+Only OpenFlow 1.1 and 1.2 support \fBinvalid_ttl\fR; Open vSwitch also
+implements it for OpenFlow 1.0 as an extension.
.IP
\fBwatch:\fR[\fB\fIspec\fR...] causes \fBovs\-ofctl\fR to send a
``monitor request'' Nicira extension message to the switch at
.IP
The following flags describe the state of the tracking:
.RS
-.IP "\fB0x80: trk\fR"
-This packet is tracked, meaning that it has previously traversed the connection
-tracker. If this flag is not set, then no other flags will be set. If this flag
-is set, then the packet is tracked and other flags may also be set.
-.IP "\fB0x40: rpl\fR"
+.IP "\fB0x01: new\fR"
+This is the beginning of a new connection. This flag may only be present for
+uncommitted connections.
+.IP "\fB0x02: est\fR"
+This is part of an already existing connection. This flag may only be present
+for committed connections.
+.IP "\fB0x04: rel\fR"
+This is a connection that is related to an existing connection, for
+instance ICMP "destination unreachable" messages or FTP data connections. This
+flag may only be present for committed connections.
+.IP "\fB0x08: rpl\fR"
The flow is in the reply direction, meaning it did not initiate the
connection. This flag may only be present for committed connections.
-.IP "\fB0x20: inv\fR"
+.IP "\fB0x10: inv\fR"
The state is invalid, meaning that the connection tracker couldn't identify the
connection. This flag is a catch-all for any problems that the connection
tracker may have, for example:
.PP
- Packets are unexpected length for protocol.
.RE
-.IP "\fB0x01: new\fR"
-This is the beginning of a new connection. This flag may only be present for
-uncommitted connections.
-.IP "\fB0x02: est\fR"
-This is part of an already existing connection. This flag may only be present
-for committed connections.
-.IP "\fB0x04: rel\fR"
-This is a connection that is related to an existing connection, for
-instance ICMP "destination unreachable" messages or FTP data connections. This
-flag may only be present for committed connections.
+.IP "\fB0x20: trk\fR"
+This packet is tracked, meaning that it has previously traversed the connection
+tracker. If this flag is not set, then no other flags will be set. If this flag
+is set, then the packet is tracked and other flags may also be set.
.PP
This field was introduced in Open vSwitch 2.5.
.RE
Currently, connection tracking is only available on Linux kernels with the
nf_conntrack module loaded.
.
-.RE
-.
.IP \fBdec_ttl\fR
.IQ \fBdec_ttl(\fIid1\fR[\fB,\fIid2\fR]...\fB)\fR
Decrement TTL of IPv4 packet or hop limit of IPv6 packet. If the
projects / cascardo / ovs.git / blobdiff