HID: rmi: Disable scanning if the device is not a wake source
authorAndrew Duggan <aduggan@synaptics.com>
Mon, 6 Jul 2015 23:48:31 +0000 (16:48 -0700)
committerJiri Kosina <jkosina@suse.com>
Thu, 9 Jul 2015 12:24:51 +0000 (14:24 +0200)
Some touchpads are configured with firmware which continues to scan for
fingers at a minimal scan rate even after receiving the HID power sleep
command. This allows a finger touching the touchpad to genrate a wake
event. This patch ensures that scanning is disabled if the touchpad is
not a wake source and ensures scanning is enabled on resume.

Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
drivers/hid/hid-rmi.c

index 4cf80bb..af191a2 100644 (file)
@@ -33,6 +33,9 @@
 #define RMI_READ_DATA_PENDING          1
 #define RMI_STARTED                    2
 
+#define RMI_SLEEP_NORMAL               0x0
+#define RMI_SLEEP_DEEP_SLEEP           0x1
+
 /* device flags */
 #define RMI_DEVICE                     BIT(0)
 #define RMI_DEVICE_HAS_PHYS_BUTTONS    BIT(1)
@@ -126,6 +129,8 @@ struct rmi_data {
 
        unsigned long device_flags;
        unsigned long firmware_id;
+
+       u8 f01_ctrl0;
 };
 
 #define RMI_PAGE(addr) (((addr) >> 8) & 0xff)
@@ -532,9 +537,51 @@ static int rmi_event(struct hid_device *hdev, struct hid_field *field,
 }
 
 #ifdef CONFIG_PM
+static int rmi_set_sleep_mode(struct hid_device *hdev, int sleep_mode)
+{
+       struct rmi_data *data = hid_get_drvdata(hdev);
+       int ret;
+       u8 f01_ctrl0;
+
+       f01_ctrl0 = (data->f01_ctrl0 & ~0x3) | sleep_mode;
+
+       ret = rmi_write(hdev, data->f01.control_base_addr,
+                       &f01_ctrl0);
+       if (ret) {
+               hid_err(hdev, "can not write sleep mode\n");
+               return ret;
+       }
+
+       return 0;
+}
+
+static int rmi_suspend(struct hid_device *hdev, pm_message_t message)
+{
+       if (!device_may_wakeup(hdev->dev.parent))
+               return rmi_set_sleep_mode(hdev, RMI_SLEEP_DEEP_SLEEP);
+
+       return 0;
+}
+
 static int rmi_post_reset(struct hid_device *hdev)
 {
-       return rmi_set_mode(hdev, RMI_MODE_ATTN_REPORTS);
+       int ret;
+
+       ret = rmi_set_mode(hdev, RMI_MODE_ATTN_REPORTS);
+       if (ret) {
+               hid_err(hdev, "can not set rmi mode\n");
+               return ret;
+       }
+
+       if (!device_may_wakeup(hdev->dev.parent)) {
+               ret = rmi_set_sleep_mode(hdev, RMI_SLEEP_NORMAL);
+               if (ret) {
+                       hid_err(hdev, "can not write sleep mode\n");
+                       return ret;
+               }
+       }
+
+       return ret;
 }
 
 static int rmi_post_resume(struct hid_device *hdev)
@@ -732,6 +779,12 @@ static int rmi_populate_f01(struct hid_device *hdev)
                data->firmware_id += info[2] * 65536;
        }
 
+       ret = rmi_read(hdev, data->f01.control_base_addr, &data->f01_ctrl0);
+
+       if (ret) {
+               hid_err(hdev, "can not read f01 ctrl0\n");
+               return ret;
+       }
        return 0;
 }
 
@@ -1273,6 +1326,7 @@ static struct hid_driver rmi_driver = {
        .input_mapping          = rmi_input_mapping,
        .input_configured       = rmi_input_configured,
 #ifdef CONFIG_PM
+       .suspend                = rmi_suspend,
        .resume                 = rmi_post_resume,
        .reset_resume           = rmi_post_reset,
 #endif