--- /dev/null
+Freescale i.MX25 ADC GCQ device
+
+This is a generic conversion queue device that can convert any of the
+analog inputs using the ADC unit of the i.MX25.
+
+Required properties:
+ - compatible: Should be "fsl,imx25-gcq".
+ - reg: Should be the register range of the module.
+ - interrupts: Should be the interrupt number of the module.
+ Typically this is <1>.
+ - interrupt-parent: phandle to the tsadc module of the i.MX25.
+ - #address-cells: Should be <1> (setting for the subnodes)
+ - #size-cells: Should be <0> (setting for the subnodes)
+
+Optional properties:
+ - vref-ext-supply: The regulator supplying the ADC reference voltage.
+ Required when at least one subnode uses the this reference.
+ - vref-xp-supply: The regulator supplying the ADC reference voltage on pin XP.
+ Required when at least one subnode uses this reference.
+ - vref-yp-supply: The regulator supplying the ADC reference voltage on pin YP.
+ Required when at least one subnode uses this reference.
+
+Sub-nodes:
+Optionally you can define subnodes which define the reference voltage
+for the analog inputs.
+
+Required properties for subnodes:
+ - reg: Should be the number of the analog input.
+ 0: xp
+ 1: yp
+ 2: xn
+ 3: yn
+ 4: wiper
+ 5: inaux0
+ 6: inaux1
+ 7: inaux2
+Optional properties for subnodes:
+ - fsl,adc-refp: specifies the positive reference input as defined in
+ <dt-bindings/iio/adc/fsl-imx25-gcq.h>
+ - fsl,adc-refn: specifies the negative reference input as defined in
+ <dt-bindings/iio/adc/fsl-imx25-gcq.h>
+
+Example:
+
+ adc: adc@50030800 {
+ compatible = "fsl,imx25-gcq";
+ reg = <0x50030800 0x60>;
+ interrupt-parent = <&tscadc>;
+ interrupts = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ inaux@5 {
+ reg = <5>;
+ fsl,adc-refp = <MX25_ADC_REFP_INT>;
+ fsl,adc-refn = <MX25_ADC_REFN_NGND>;
+ };
+ };
--- /dev/null
+Freescale mx25 TS conversion queue module
+
+mx25 touchscreen conversion queue module which controls the ADC unit of the
+mx25 for attached touchscreens.
+
+Required properties:
+ - compatible: Should be "fsl,imx25-tcq".
+ - reg: Memory range of the device.
+ - interrupts: Should be the interrupt number associated with this module within
+ the tscadc unit (<0>).
+ - interrupt-parent: Should be a phandle to the tscadc unit.
+ - fsl,wires: Should be '<4>' or '<5>'
+
+Optional properties:
+ - fsl,pen-debounce-ns: Pen debounce time in nanoseconds.
+ - fsl,pen-threshold: Pen-down threshold for the touchscreen. This is a value
+ between 1 and 4096. It is the ratio between the internal reference voltage
+ and the measured voltage after the plate was precharged. Resistence between
+ plates and therefore the voltage decreases with pressure so that a smaller
+ value is equivalent to a higher pressure.
+ - fsl,settling-time-ns: Settling time in nanoseconds. The settling time is before
+ the actual touch detection to wait for an even charge distribution in the
+ plate.
+
+This device includes two conversion queues which can be added as subnodes.
+The first queue is for the touchscreen, the second for general purpose ADC.
+
+Example:
+ tsc: tcq@50030400 {
+ compatible = "fsl,imx25-tcq";
+ reg = <0x50030400 0x60>;
+ interrupt-parent = <&tscadc>;
+ interrupts = <0>;
+ fsl,wires = <4>;
+ };
axp202 (X-Powers)
axp209 (X-Powers)
axp221 (X-Powers)
+axp223 (X-Powers)
Required properties:
- compatible: "x-powers,axp152", "x-powers,axp202", "x-powers,axp209",
- "x-powers,axp221"
-- reg: The I2C slave address for the AXP chip
+ "x-powers,axp221", "x-powers,axp223"
+- reg: The I2C slave address or RSB hardware address for the AXP chip
- interrupt-parent: The parent interrupt controller
- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin
- interrupt-controller: The PMIC has its own internal IRQs
LDO4 : LDO : ldo24in-supply : shared supply
LDO5 : LDO : ldo5in-supply
-AXP221 regulators, type, and corresponding input supply names:
+AXP221/AXP223 regulators, type, and corresponding input supply names:
Regulator Type Supply Name Notes
--------- ---- ----------- -----
--- /dev/null
+Freescale MX25 ADC/TSC MultiFunction Device (MFD)
+
+This device combines two general purpose conversion queues one used for general
+ADC and the other used for touchscreens.
+
+Required properties:
+ - compatible: Should be "fsl,imx25-tsadc".
+ - reg: Start address and size of the memory area of
+ the device
+ - interrupts: Interrupt for this device
+ (See: ../interrupt-controller/interrupts.txt)
+ - clocks: An 'ipg' clock (See: ../clock/clock-bindings.txt)
+ - interrupt-controller: This device is an interrupt controller. It
+ controls the interrupts of both
+ conversion queues.
+ - #interrupt-cells: Should be '<1>'.
+ - #address-cells: Should be '<1>'.
+ - #size-cells: Should be '<1>'.
+
+This device includes two conversion queues which can be added as subnodes.
+The first queue is for the touchscreen, the second for general purpose ADC.
+
+Example:
+ tscadc: tscadc@50030000 {
+ compatible = "fsl,imx25-tsadc";
+ reg = <0x50030000 0xc>;
+ interrupts = <46>;
+ clocks = <&clks 119>;
+ clock-names = "ipg";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ tsc: tcq@50030400 {
+ compatible = "fsl,imx25-tcq";
+ reg = <0x50030400 0x60>;
+ ...
+ };
+
+ adc: gcq@50030800 {
+ compatible = "fsl,imx25-gcq";
+ reg = <0x50030800 0x60>;
+ ...
+ };
+ };
--- /dev/null
+* TPS65912 Power Management Integrated Circuit bindings
+
+Required properties:
+ - compatible : Should be "ti,tps65912".
+ - reg : Slave address or chip select number (I2C / SPI).
+ - interrupt-parent : The parent interrupt controller.
+ - interrupts : The interrupt line the device is connected to.
+ - interrupt-controller : Marks the device node as an interrupt controller.
+ - #interrupt-cells : The number of cells to describe an IRQ, should be 2.
+ The first cell is the IRQ number.
+ The second cell is the flags, encoded as trigger
+ masks from ../interrupt-controller/interrupts.txt.
+ - gpio-controller : Marks the device node as a GPIO Controller.
+ - #gpio-cells : Should be two. The first cell is the pin number and
+ the second cell is used to specify flags.
+ See ../gpio/gpio.txt for more information.
+ - regulators: : List of child nodes that specify the regulator
+ initialization data. Child nodes must be named
+ after their hardware counterparts: dcdc[1-4] and
+ ldo[1-10]. Each child nodes is defined using the
+ standard binding for regulators.
+
+Example:
+
+ pmic: tps65912@2d {
+ compatible = "ti,tps65912";
+ reg = <0x2d>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ regulators {
+ dcdc1 {
+ regulator-name = "vdd_core";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <1144000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1 {
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <1900000>;
+ regulator-max-microvolt = <1900000>;
+ };
+ };
+ };
config GPIO_TPS65912
tristate "TI TPS65912 GPIO"
- depends on (MFD_TPS65912_I2C || MFD_TPS65912_SPI)
+ depends on MFD_TPS65912
help
This driver supports TPS65912 gpio chip
/*
- * Copyright 2011 Texas Instruments Inc.
+ * GPIO driver for TI TPS65912x PMICs
*
- * Author: Margarita Olaya <magi@slimlogic.co.uk>
+ * Copyright (C) 2015 Texas Instruments Incorporated - http://www.ti.com/
+ * Andrew F. Davis <afd@ti.com>
*
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
*
- * This driver is based on wm8350 implementation.
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether expressed or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License version 2 for more details.
+ *
+ * Based on the Arizona GPIO driver and the previous TPS65912 driver by
+ * Margarita Olaya Cabrera <magi@slimlogic.co.uk>
*/
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/errno.h>
#include <linux/gpio.h>
-#include <linux/mfd/core.h>
+#include <linux/module.h>
#include <linux/platform_device.h>
-#include <linux/seq_file.h>
-#include <linux/slab.h>
+
#include <linux/mfd/tps65912.h>
-struct tps65912_gpio_data {
- struct tps65912 *tps65912;
+struct tps65912_gpio {
struct gpio_chip gpio_chip;
+ struct tps65912 *tps;
};
-static int tps65912_gpio_get(struct gpio_chip *gc, unsigned offset)
+static int tps65912_gpio_get_direction(struct gpio_chip *gc,
+ unsigned offset)
{
- struct tps65912_gpio_data *tps65912_gpio = gpiochip_get_data(gc);
- struct tps65912 *tps65912 = tps65912_gpio->tps65912;
- int val;
+ struct tps65912_gpio *gpio = gpiochip_get_data(gc);
- val = tps65912_reg_read(tps65912, TPS65912_GPIO1 + offset);
+ int ret, val;
- if (val & GPIO_STS_MASK)
- return 1;
+ ret = regmap_read(gpio->tps->regmap, TPS65912_GPIO1 + offset, &val);
+ if (ret)
+ return ret;
- return 0;
+ if (val & GPIO_CFG_MASK)
+ return GPIOF_DIR_OUT;
+ else
+ return GPIOF_DIR_IN;
}
-static void tps65912_gpio_set(struct gpio_chip *gc, unsigned offset,
- int value)
+static int tps65912_gpio_direction_input(struct gpio_chip *gc, unsigned offset)
{
- struct tps65912_gpio_data *tps65912_gpio = gpiochip_get_data(gc);
- struct tps65912 *tps65912 = tps65912_gpio->tps65912;
+ struct tps65912_gpio *gpio = gpiochip_get_data(gc);
- if (value)
- tps65912_set_bits(tps65912, TPS65912_GPIO1 + offset,
- GPIO_SET_MASK);
- else
- tps65912_clear_bits(tps65912, TPS65912_GPIO1 + offset,
- GPIO_SET_MASK);
+ return regmap_update_bits(gpio->tps->regmap, TPS65912_GPIO1 + offset,
+ GPIO_CFG_MASK, 0);
}
-static int tps65912_gpio_output(struct gpio_chip *gc, unsigned offset,
- int value)
+static int tps65912_gpio_direction_output(struct gpio_chip *gc,
+ unsigned offset, int value)
{
- struct tps65912_gpio_data *tps65912_gpio = gpiochip_get_data(gc);
- struct tps65912 *tps65912 = tps65912_gpio->tps65912;
+ struct tps65912_gpio *gpio = gpiochip_get_data(gc);
/* Set the initial value */
- tps65912_gpio_set(gc, offset, value);
+ regmap_update_bits(gpio->tps->regmap, TPS65912_GPIO1 + offset,
+ GPIO_SET_MASK, value ? GPIO_SET_MASK : 0);
+
+ return regmap_update_bits(gpio->tps->regmap, TPS65912_GPIO1 + offset,
+ GPIO_CFG_MASK, GPIO_CFG_MASK);
+}
+
+static int tps65912_gpio_get(struct gpio_chip *gc, unsigned offset)
+{
+ struct tps65912_gpio *gpio = gpiochip_get_data(gc);
+ int ret, val;
+
+ ret = regmap_read(gpio->tps->regmap, TPS65912_GPIO1 + offset, &val);
+ if (ret)
+ return ret;
- return tps65912_set_bits(tps65912, TPS65912_GPIO1 + offset,
- GPIO_CFG_MASK);
+ if (val & GPIO_STS_MASK)
+ return 1;
+
+ return 0;
}
-static int tps65912_gpio_input(struct gpio_chip *gc, unsigned offset)
+static void tps65912_gpio_set(struct gpio_chip *gc, unsigned offset,
+ int value)
{
- struct tps65912_gpio_data *tps65912_gpio = gpiochip_get_data(gc);
- struct tps65912 *tps65912 = tps65912_gpio->tps65912;
+ struct tps65912_gpio *gpio = gpiochip_get_data(gc);
- return tps65912_clear_bits(tps65912, TPS65912_GPIO1 + offset,
- GPIO_CFG_MASK);
+ regmap_update_bits(gpio->tps->regmap, TPS65912_GPIO1 + offset,
+ GPIO_SET_MASK, value ? GPIO_SET_MASK : 0);
}
static struct gpio_chip template_chip = {
- .label = "tps65912",
+ .label = "tps65912-gpio",
.owner = THIS_MODULE,
- .direction_input = tps65912_gpio_input,
- .direction_output = tps65912_gpio_output,
+ .get_direction = tps65912_gpio_get_direction,
+ .direction_input = tps65912_gpio_direction_input,
+ .direction_output = tps65912_gpio_direction_output,
.get = tps65912_gpio_get,
.set = tps65912_gpio_set,
- .can_sleep = true,
- .ngpio = 5,
.base = -1,
+ .ngpio = 5,
+ .can_sleep = true,
};
static int tps65912_gpio_probe(struct platform_device *pdev)
{
- struct tps65912 *tps65912 = dev_get_drvdata(pdev->dev.parent);
- struct tps65912_board *pdata = dev_get_platdata(tps65912->dev);
- struct tps65912_gpio_data *tps65912_gpio;
+ struct tps65912 *tps = dev_get_drvdata(pdev->dev.parent);
+ struct tps65912_gpio *gpio;
int ret;
- tps65912_gpio = devm_kzalloc(&pdev->dev, sizeof(*tps65912_gpio),
- GFP_KERNEL);
- if (tps65912_gpio == NULL)
+ gpio = devm_kzalloc(&pdev->dev, sizeof(*gpio), GFP_KERNEL);
+ if (!gpio)
return -ENOMEM;
- tps65912_gpio->tps65912 = tps65912;
- tps65912_gpio->gpio_chip = template_chip;
- tps65912_gpio->gpio_chip.parent = &pdev->dev;
- if (pdata && pdata->gpio_base)
- tps65912_gpio->gpio_chip.base = pdata->gpio_base;
+ gpio->tps = dev_get_drvdata(pdev->dev.parent);
+ gpio->gpio_chip = template_chip;
+ gpio->gpio_chip.parent = tps->dev;
- ret = gpiochip_add_data(&tps65912_gpio->gpio_chip, tps65912_gpio);
+ ret = gpiochip_add_data(&gpio->gpio_chip, gpio);
if (ret < 0) {
- dev_err(&pdev->dev, "Failed to register gpiochip, %d\n", ret);
+ dev_err(&pdev->dev, "Could not register gpiochip, %d\n", ret);
return ret;
}
- platform_set_drvdata(pdev, tps65912_gpio);
+ platform_set_drvdata(pdev, gpio);
- return ret;
+ return 0;
}
static int tps65912_gpio_remove(struct platform_device *pdev)
{
- struct tps65912_gpio_data *tps65912_gpio = platform_get_drvdata(pdev);
+ struct tps65912_gpio *gpio = platform_get_drvdata(pdev);
+
+ gpiochip_remove(&gpio->gpio_chip);
- gpiochip_remove(&tps65912_gpio->gpio_chip);
return 0;
}
+static const struct platform_device_id tps65912_gpio_id_table[] = {
+ { "tps65912-gpio", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(platform, tps65912_gpio_id_table);
+
static struct platform_driver tps65912_gpio_driver = {
.driver = {
.name = "tps65912-gpio",
},
.probe = tps65912_gpio_probe,
.remove = tps65912_gpio_remove,
+ .id_table = tps65912_gpio_id_table,
};
+module_platform_driver(tps65912_gpio_driver);
-static int __init tps65912_gpio_init(void)
-{
- return platform_driver_register(&tps65912_gpio_driver);
-}
-subsys_initcall(tps65912_gpio_init);
-
-static void __exit tps65912_gpio_exit(void)
-{
- platform_driver_unregister(&tps65912_gpio_driver);
-}
-module_exit(tps65912_gpio_exit);
-
-MODULE_AUTHOR("Margarita Olaya Cabrera <magi@slimlogic.co.uk>");
-MODULE_DESCRIPTION("GPIO interface for TPS65912 PMICs");
+MODULE_AUTHOR("Andrew F. Davis <afd@ti.com>");
+MODULE_DESCRIPTION("TPS65912 GPIO driver");
MODULE_LICENSE("GPL v2");
-MODULE_ALIAS("platform:tps65912-gpio");
To compile this driver as a module, choose M here: the module will be
called exynos_adc.
+config FSL_MX25_ADC
+ tristate "Freescale MX25 ADC driver"
+ depends on MFD_MX25_TSADC
+ help
+ Generic Conversion Queue driver used for general purpose ADC in the
+ MX25. This driver supports single measurements using the MX25 ADC.
+
config HI8435
tristate "Holt Integrated Circuits HI-8435 threshold detector"
select IIO_TRIGGERED_EVENT
obj-$(CONFIG_CC10001_ADC) += cc10001_adc.o
obj-$(CONFIG_DA9150_GPADC) += da9150-gpadc.o
obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
+obj-$(CONFIG_FSL_MX25_ADC) += fsl-imx25-gcq.o
obj-$(CONFIG_HI8435) += hi8435.o
obj-$(CONFIG_IMX7D_ADC) += imx7d_adc.o
obj-$(CONFIG_INA2XX_ADC) += ina2xx-adc.o
--- /dev/null
+/*
+ * Copyright (C) 2014-2015 Pengutronix, Markus Pargmann <mpa@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or modify it under
+ * the terms of the GNU General Public License version 2 as published by the
+ * Free Software Foundation.
+ *
+ * This is the driver for the imx25 GCQ (Generic Conversion Queue)
+ * connected to the imx25 ADC.
+ */
+
+#include <dt-bindings/iio/adc/fsl-imx25-gcq.h>
+#include <linux/clk.h>
+#include <linux/iio/iio.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/imx25-tsadc.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+
+#define MX25_GCQ_TIMEOUT (msecs_to_jiffies(2000))
+
+static const char * const driver_name = "mx25-gcq";
+
+enum mx25_gcq_cfgs {
+ MX25_CFG_XP = 0,
+ MX25_CFG_YP,
+ MX25_CFG_XN,
+ MX25_CFG_YN,
+ MX25_CFG_WIPER,
+ MX25_CFG_INAUX0,
+ MX25_CFG_INAUX1,
+ MX25_CFG_INAUX2,
+ MX25_NUM_CFGS,
+};
+
+struct mx25_gcq_priv {
+ struct regmap *regs;
+ struct completion completed;
+ struct clk *clk;
+ int irq;
+ struct regulator *vref[4];
+ u32 channel_vref_mv[MX25_NUM_CFGS];
+};
+
+#define MX25_CQG_CHAN(chan, id) {\
+ .type = IIO_VOLTAGE,\
+ .indexed = 1,\
+ .channel = chan,\
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
+ BIT(IIO_CHAN_INFO_SCALE),\
+ .datasheet_name = id,\
+}
+
+static const struct iio_chan_spec mx25_gcq_channels[MX25_NUM_CFGS] = {
+ MX25_CQG_CHAN(MX25_CFG_XP, "xp"),
+ MX25_CQG_CHAN(MX25_CFG_YP, "yp"),
+ MX25_CQG_CHAN(MX25_CFG_XN, "xn"),
+ MX25_CQG_CHAN(MX25_CFG_YN, "yn"),
+ MX25_CQG_CHAN(MX25_CFG_WIPER, "wiper"),
+ MX25_CQG_CHAN(MX25_CFG_INAUX0, "inaux0"),
+ MX25_CQG_CHAN(MX25_CFG_INAUX1, "inaux1"),
+ MX25_CQG_CHAN(MX25_CFG_INAUX2, "inaux2"),
+};
+
+static const char * const mx25_gcq_refp_names[] = {
+ [MX25_ADC_REFP_YP] = "yp",
+ [MX25_ADC_REFP_XP] = "xp",
+ [MX25_ADC_REFP_INT] = "int",
+ [MX25_ADC_REFP_EXT] = "ext",
+};
+
+static irqreturn_t mx25_gcq_irq(int irq, void *data)
+{
+ struct mx25_gcq_priv *priv = data;
+ u32 stats;
+
+ regmap_read(priv->regs, MX25_ADCQ_SR, &stats);
+
+ if (stats & MX25_ADCQ_SR_EOQ) {
+ regmap_update_bits(priv->regs, MX25_ADCQ_MR,
+ MX25_ADCQ_MR_EOQ_IRQ, MX25_ADCQ_MR_EOQ_IRQ);
+ complete(&priv->completed);
+ }
+
+ /* Disable conversion queue run */
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS, 0);
+
+ /* Acknowledge all possible irqs */
+ regmap_write(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_FRR |
+ MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR |
+ MX25_ADCQ_SR_EOQ | MX25_ADCQ_SR_PD);
+
+ return IRQ_HANDLED;
+}
+
+static int mx25_gcq_get_raw_value(struct device *dev,
+ struct iio_chan_spec const *chan,
+ struct mx25_gcq_priv *priv,
+ int *val)
+{
+ long timeout;
+ u32 data;
+
+ /* Setup the configuration we want to use */
+ regmap_write(priv->regs, MX25_ADCQ_ITEM_7_0,
+ MX25_ADCQ_ITEM(0, chan->channel));
+
+ regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_EOQ_IRQ, 0);
+
+ /* Trigger queue for one run */
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FQS,
+ MX25_ADCQ_CR_FQS);
+
+ timeout = wait_for_completion_interruptible_timeout(
+ &priv->completed, MX25_GCQ_TIMEOUT);
+ if (timeout < 0) {
+ dev_err(dev, "ADC wait for measurement failed\n");
+ return timeout;
+ } else if (timeout == 0) {
+ dev_err(dev, "ADC timed out\n");
+ return -ETIMEDOUT;
+ }
+
+ regmap_read(priv->regs, MX25_ADCQ_FIFO, &data);
+
+ *val = MX25_ADCQ_FIFO_DATA(data);
+
+ return IIO_VAL_INT;
+}
+
+static int mx25_gcq_read_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan, int *val,
+ int *val2, long mask)
+{
+ struct mx25_gcq_priv *priv = iio_priv(indio_dev);
+ int ret;
+
+ switch (mask) {
+ case IIO_CHAN_INFO_RAW:
+ mutex_lock(&indio_dev->mlock);
+ ret = mx25_gcq_get_raw_value(&indio_dev->dev, chan, priv, val);
+ mutex_unlock(&indio_dev->mlock);
+ return ret;
+
+ case IIO_CHAN_INFO_SCALE:
+ *val = priv->channel_vref_mv[chan->channel];
+ *val2 = 12;
+ return IIO_VAL_FRACTIONAL_LOG2;
+
+ default:
+ return -EINVAL;
+ }
+}
+
+static const struct iio_info mx25_gcq_iio_info = {
+ .read_raw = mx25_gcq_read_raw,
+};
+
+static const struct regmap_config mx25_gcq_regconfig = {
+ .max_register = 0x5c,
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+};
+
+static int mx25_gcq_setup_cfgs(struct platform_device *pdev,
+ struct mx25_gcq_priv *priv)
+{
+ struct device_node *np = pdev->dev.of_node;
+ struct device_node *child;
+ struct device *dev = &pdev->dev;
+ unsigned int refp_used[4] = {};
+ int ret, i;
+
+ /*
+ * Setup all configurations registers with a default conversion
+ * configuration for each input
+ */
+ for (i = 0; i < MX25_NUM_CFGS; ++i)
+ regmap_write(priv->regs, MX25_ADCQ_CFG(i),
+ MX25_ADCQ_CFG_YPLL_OFF |
+ MX25_ADCQ_CFG_XNUR_OFF |
+ MX25_ADCQ_CFG_XPUL_OFF |
+ MX25_ADCQ_CFG_REFP_INT |
+ MX25_ADCQ_CFG_IN(i) |
+ MX25_ADCQ_CFG_REFN_NGND2);
+
+ /*
+ * First get all regulators to store them in channel_vref_mv if
+ * necessary. Later we use that information for proper IIO scale
+ * information.
+ */
+ priv->vref[MX25_ADC_REFP_INT] = NULL;
+ priv->vref[MX25_ADC_REFP_EXT] =
+ devm_regulator_get_optional(&pdev->dev, "vref-ext");
+ priv->vref[MX25_ADC_REFP_XP] =
+ devm_regulator_get_optional(&pdev->dev, "vref-xp");
+ priv->vref[MX25_ADC_REFP_YP] =
+ devm_regulator_get_optional(&pdev->dev, "vref-yp");
+
+ for_each_child_of_node(np, child) {
+ u32 reg;
+ u32 refp = MX25_ADCQ_CFG_REFP_INT;
+ u32 refn = MX25_ADCQ_CFG_REFN_NGND2;
+
+ ret = of_property_read_u32(child, "reg", ®);
+ if (ret) {
+ dev_err(dev, "Failed to get reg property\n");
+ return ret;
+ }
+
+ if (reg >= MX25_NUM_CFGS) {
+ dev_err(dev,
+ "reg value is greater than the number of available configuration registers\n");
+ return -EINVAL;
+ }
+
+ of_property_read_u32(child, "fsl,adc-refp", &refp);
+ of_property_read_u32(child, "fsl,adc-refn", &refn);
+
+ switch (refp) {
+ case MX25_ADC_REFP_EXT:
+ case MX25_ADC_REFP_XP:
+ case MX25_ADC_REFP_YP:
+ if (IS_ERR(priv->vref[refp])) {
+ dev_err(dev, "Error, trying to use external voltage reference without a vref-%s regulator.",
+ mx25_gcq_refp_names[refp]);
+ return PTR_ERR(priv->vref[refp]);
+ }
+ priv->channel_vref_mv[reg] =
+ regulator_get_voltage(priv->vref[refp]);
+ /* Conversion from uV to mV */
+ priv->channel_vref_mv[reg] /= 1000;
+ break;
+ case MX25_ADC_REFP_INT:
+ priv->channel_vref_mv[reg] = 2500;
+ break;
+ default:
+ dev_err(dev, "Invalid positive reference %d\n", refp);
+ return -EINVAL;
+ }
+
+ ++refp_used[refp];
+
+ /*
+ * Shift the read values to the correct positions within the
+ * register.
+ */
+ refp = MX25_ADCQ_CFG_REFP(refp);
+ refn = MX25_ADCQ_CFG_REFN(refn);
+
+ if ((refp & MX25_ADCQ_CFG_REFP_MASK) != refp) {
+ dev_err(dev, "Invalid fsl,adc-refp property value\n");
+ return -EINVAL;
+ }
+ if ((refn & MX25_ADCQ_CFG_REFN_MASK) != refn) {
+ dev_err(dev, "Invalid fsl,adc-refn property value\n");
+ return -EINVAL;
+ }
+
+ regmap_update_bits(priv->regs, MX25_ADCQ_CFG(reg),
+ MX25_ADCQ_CFG_REFP_MASK |
+ MX25_ADCQ_CFG_REFN_MASK,
+ refp | refn);
+ }
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST,
+ MX25_ADCQ_CR_FRST | MX25_ADCQ_CR_QRST);
+
+ regmap_write(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_PDMSK | MX25_ADCQ_CR_QSM_FQS);
+
+ /* Remove unused regulators */
+ for (i = 0; i != 4; ++i) {
+ if (!refp_used[i]) {
+ if (!IS_ERR_OR_NULL(priv->vref[i]))
+ devm_regulator_put(priv->vref[i]);
+ priv->vref[i] = NULL;
+ }
+ }
+
+ return 0;
+}
+
+static int mx25_gcq_probe(struct platform_device *pdev)
+{
+ struct iio_dev *indio_dev;
+ struct mx25_gcq_priv *priv;
+ struct mx25_tsadc *tsadc = dev_get_drvdata(pdev->dev.parent);
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ void __iomem *mem;
+ int ret;
+ int i;
+
+ indio_dev = devm_iio_device_alloc(&pdev->dev, sizeof(*priv));
+ if (!indio_dev)
+ return -ENOMEM;
+
+ priv = iio_priv(indio_dev);
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ mem = devm_ioremap_resource(dev, res);
+ if (IS_ERR(mem))
+ return PTR_ERR(mem);
+
+ priv->regs = devm_regmap_init_mmio(dev, mem, &mx25_gcq_regconfig);
+ if (IS_ERR(priv->regs)) {
+ dev_err(dev, "Failed to initialize regmap\n");
+ return PTR_ERR(priv->regs);
+ }
+
+ init_completion(&priv->completed);
+
+ ret = mx25_gcq_setup_cfgs(pdev, priv);
+ if (ret)
+ return ret;
+
+ for (i = 0; i != 4; ++i) {
+ if (!priv->vref[i])
+ continue;
+
+ ret = regulator_enable(priv->vref[i]);
+ if (ret)
+ goto err_regulator_disable;
+ }
+
+ priv->clk = tsadc->clk;
+ ret = clk_prepare_enable(priv->clk);
+ if (ret) {
+ dev_err(dev, "Failed to enable clock\n");
+ goto err_vref_disable;
+ }
+
+ priv->irq = platform_get_irq(pdev, 0);
+ if (priv->irq <= 0) {
+ dev_err(dev, "Failed to get IRQ\n");
+ ret = priv->irq;
+ if (!ret)
+ ret = -ENXIO;
+ goto err_clk_unprepare;
+ }
+
+ ret = request_irq(priv->irq, mx25_gcq_irq, 0, pdev->name, priv);
+ if (ret) {
+ dev_err(dev, "Failed requesting IRQ\n");
+ goto err_clk_unprepare;
+ }
+
+ indio_dev->dev.parent = &pdev->dev;
+ indio_dev->channels = mx25_gcq_channels;
+ indio_dev->num_channels = ARRAY_SIZE(mx25_gcq_channels);
+ indio_dev->info = &mx25_gcq_iio_info;
+ indio_dev->name = driver_name;
+
+ ret = iio_device_register(indio_dev);
+ if (ret) {
+ dev_err(dev, "Failed to register iio device\n");
+ goto err_irq_free;
+ }
+
+ platform_set_drvdata(pdev, indio_dev);
+
+ return 0;
+
+err_irq_free:
+ free_irq(priv->irq, priv);
+err_clk_unprepare:
+ clk_disable_unprepare(priv->clk);
+err_vref_disable:
+ i = 4;
+err_regulator_disable:
+ for (; i-- > 0;) {
+ if (priv->vref[i])
+ regulator_disable(priv->vref[i]);
+ }
+ return ret;
+}
+
+static int mx25_gcq_remove(struct platform_device *pdev)
+{
+ struct iio_dev *indio_dev = platform_get_drvdata(pdev);
+ struct mx25_gcq_priv *priv = iio_priv(indio_dev);
+ int i;
+
+ iio_device_unregister(indio_dev);
+ free_irq(priv->irq, priv);
+ clk_disable_unprepare(priv->clk);
+ for (i = 4; i-- > 0;) {
+ if (priv->vref[i])
+ regulator_disable(priv->vref[i]);
+ }
+
+ return 0;
+}
+
+static const struct of_device_id mx25_gcq_ids[] = {
+ { .compatible = "fsl,imx25-gcq", },
+ { /* Sentinel */ }
+};
+
+static struct platform_driver mx25_gcq_driver = {
+ .driver = {
+ .name = "mx25-gcq",
+ .of_match_table = mx25_gcq_ids,
+ },
+ .probe = mx25_gcq_probe,
+ .remove = mx25_gcq_remove,
+};
+module_platform_driver(mx25_gcq_driver);
+
+MODULE_DESCRIPTION("ADC driver for Freescale mx25");
+MODULE_AUTHOR("Markus Pargmann <mpa@pengutronix.de>");
+MODULE_LICENSE("GPL v2");
To compile this driver as a module, choose M here: the
module will be called usbtouchscreen.
+config TOUCHSCREEN_MX25
+ tristate "Freescale i.MX25 touchscreen input driver"
+ depends on MFD_MX25_TSADC
+ help
+ Enable support for touchscreen connected to your i.MX25.
+
+ To compile this driver as a module, choose M here: the
+ module will be called fsl-imx25-tcq.
+
config TOUCHSCREEN_MC13783
tristate "Freescale MC13783 touchscreen input driver"
depends on MFD_MC13XXX
obj-$(CONFIG_TOUCHSCREEN_IPROC) += bcm_iproc_tsc.o
obj-$(CONFIG_TOUCHSCREEN_LPC32XX) += lpc32xx_ts.o
obj-$(CONFIG_TOUCHSCREEN_MAX11801) += max11801_ts.o
+obj-$(CONFIG_TOUCHSCREEN_MX25) += fsl-imx25-tcq.o
obj-$(CONFIG_TOUCHSCREEN_MC13783) += mc13783_ts.o
obj-$(CONFIG_TOUCHSCREEN_MCS5000) += mcs5000_ts.o
obj-$(CONFIG_TOUCHSCREEN_MIGOR) += migor_ts.o
--- /dev/null
+/*
+ * Copyright (C) 2014-2015 Pengutronix, Markus Pargmann <mpa@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or modify it under
+ * the terms of the GNU General Public License version 2 as published by the
+ * Free Software Foundation.
+ *
+ * Based on driver from 2011:
+ * Juergen Beisert, Pengutronix <kernel@pengutronix.de>
+ *
+ * This is the driver for the imx25 TCQ (Touchscreen Conversion Queue)
+ * connected to the imx25 ADC.
+ */
+
+#include <linux/clk.h>
+#include <linux/device.h>
+#include <linux/input.h>
+#include <linux/interrupt.h>
+#include <linux/mfd/imx25-tsadc.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+static const char mx25_tcq_name[] = "mx25-tcq";
+
+enum mx25_tcq_mode {
+ MX25_TS_4WIRE,
+};
+
+struct mx25_tcq_priv {
+ struct regmap *regs;
+ struct regmap *core_regs;
+ struct input_dev *idev;
+ enum mx25_tcq_mode mode;
+ unsigned int pen_threshold;
+ unsigned int sample_count;
+ unsigned int expected_samples;
+ unsigned int pen_debounce;
+ unsigned int settling_time;
+ struct clk *clk;
+ int irq;
+ struct device *dev;
+};
+
+static struct regmap_config mx25_tcq_regconfig = {
+ .fast_io = true,
+ .max_register = 0x5c,
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+};
+
+static const struct of_device_id mx25_tcq_ids[] = {
+ { .compatible = "fsl,imx25-tcq", },
+ { /* Sentinel */ }
+};
+
+#define TSC_4WIRE_PRE_INDEX 0
+#define TSC_4WIRE_X_INDEX 1
+#define TSC_4WIRE_Y_INDEX 2
+#define TSC_4WIRE_POST_INDEX 3
+#define TSC_4WIRE_LEAVE 4
+
+#define MX25_TSC_DEF_THRESHOLD 80
+#define TSC_MAX_SAMPLES 16
+
+#define MX25_TSC_REPEAT_WAIT 14
+
+enum mx25_adc_configurations {
+ MX25_CFG_PRECHARGE = 0,
+ MX25_CFG_TOUCH_DETECT,
+ MX25_CFG_X_MEASUREMENT,
+ MX25_CFG_Y_MEASUREMENT,
+};
+
+#define MX25_PRECHARGE_VALUE (\
+ MX25_ADCQ_CFG_YPLL_OFF | \
+ MX25_ADCQ_CFG_XNUR_OFF | \
+ MX25_ADCQ_CFG_XPUL_HIGH | \
+ MX25_ADCQ_CFG_REFP_INT | \
+ MX25_ADCQ_CFG_IN_XP | \
+ MX25_ADCQ_CFG_REFN_NGND2 | \
+ MX25_ADCQ_CFG_IGS)
+
+#define MX25_TOUCH_DETECT_VALUE (\
+ MX25_ADCQ_CFG_YNLR | \
+ MX25_ADCQ_CFG_YPLL_OFF | \
+ MX25_ADCQ_CFG_XNUR_OFF | \
+ MX25_ADCQ_CFG_XPUL_OFF | \
+ MX25_ADCQ_CFG_REFP_INT | \
+ MX25_ADCQ_CFG_IN_XP | \
+ MX25_ADCQ_CFG_REFN_NGND2 | \
+ MX25_ADCQ_CFG_PENIACK)
+
+static void imx25_setup_queue_cfgs(struct mx25_tcq_priv *priv,
+ unsigned int settling_cnt)
+{
+ u32 precharge_cfg =
+ MX25_PRECHARGE_VALUE |
+ MX25_ADCQ_CFG_SETTLING_TIME(settling_cnt);
+ u32 touch_detect_cfg =
+ MX25_TOUCH_DETECT_VALUE |
+ MX25_ADCQ_CFG_NOS(1) |
+ MX25_ADCQ_CFG_SETTLING_TIME(settling_cnt);
+
+ regmap_write(priv->core_regs, MX25_TSC_TICR, precharge_cfg);
+
+ /* PRECHARGE */
+ regmap_write(priv->regs, MX25_ADCQ_CFG(MX25_CFG_PRECHARGE),
+ precharge_cfg);
+
+ /* TOUCH_DETECT */
+ regmap_write(priv->regs, MX25_ADCQ_CFG(MX25_CFG_TOUCH_DETECT),
+ touch_detect_cfg);
+
+ /* X Measurement */
+ regmap_write(priv->regs, MX25_ADCQ_CFG(MX25_CFG_X_MEASUREMENT),
+ MX25_ADCQ_CFG_YPLL_OFF |
+ MX25_ADCQ_CFG_XNUR_LOW |
+ MX25_ADCQ_CFG_XPUL_HIGH |
+ MX25_ADCQ_CFG_REFP_XP |
+ MX25_ADCQ_CFG_IN_YP |
+ MX25_ADCQ_CFG_REFN_XN |
+ MX25_ADCQ_CFG_NOS(priv->sample_count) |
+ MX25_ADCQ_CFG_SETTLING_TIME(settling_cnt));
+
+ /* Y Measurement */
+ regmap_write(priv->regs, MX25_ADCQ_CFG(MX25_CFG_Y_MEASUREMENT),
+ MX25_ADCQ_CFG_YNLR |
+ MX25_ADCQ_CFG_YPLL_HIGH |
+ MX25_ADCQ_CFG_XNUR_OFF |
+ MX25_ADCQ_CFG_XPUL_OFF |
+ MX25_ADCQ_CFG_REFP_YP |
+ MX25_ADCQ_CFG_IN_XP |
+ MX25_ADCQ_CFG_REFN_YN |
+ MX25_ADCQ_CFG_NOS(priv->sample_count) |
+ MX25_ADCQ_CFG_SETTLING_TIME(settling_cnt));
+
+ /* Enable the touch detection right now */
+ regmap_write(priv->core_regs, MX25_TSC_TICR, touch_detect_cfg |
+ MX25_ADCQ_CFG_IGS);
+}
+
+static int imx25_setup_queue_4wire(struct mx25_tcq_priv *priv,
+ unsigned settling_cnt, int *items)
+{
+ imx25_setup_queue_cfgs(priv, settling_cnt);
+
+ /* Setup the conversion queue */
+ regmap_write(priv->regs, MX25_ADCQ_ITEM_7_0,
+ MX25_ADCQ_ITEM(0, MX25_CFG_PRECHARGE) |
+ MX25_ADCQ_ITEM(1, MX25_CFG_TOUCH_DETECT) |
+ MX25_ADCQ_ITEM(2, MX25_CFG_X_MEASUREMENT) |
+ MX25_ADCQ_ITEM(3, MX25_CFG_Y_MEASUREMENT) |
+ MX25_ADCQ_ITEM(4, MX25_CFG_PRECHARGE) |
+ MX25_ADCQ_ITEM(5, MX25_CFG_TOUCH_DETECT));
+
+ /*
+ * We measure X/Y with 'sample_count' number of samples and execute a
+ * touch detection twice, with 1 sample each
+ */
+ priv->expected_samples = priv->sample_count * 2 + 2;
+ *items = 6;
+
+ return 0;
+}
+
+static void mx25_tcq_disable_touch_irq(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_PDMSK,
+ MX25_ADCQ_CR_PDMSK);
+}
+
+static void mx25_tcq_enable_touch_irq(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_PDMSK, 0);
+}
+
+static void mx25_tcq_disable_fifo_irq(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_FDRY_IRQ,
+ MX25_ADCQ_MR_FDRY_IRQ);
+}
+
+static void mx25_tcq_enable_fifo_irq(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_FDRY_IRQ, 0);
+}
+
+static void mx25_tcq_force_queue_start(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_FQS,
+ MX25_ADCQ_CR_FQS);
+}
+
+static void mx25_tcq_force_queue_stop(struct mx25_tcq_priv *priv)
+{
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_FQS, 0);
+}
+
+static void mx25_tcq_fifo_reset(struct mx25_tcq_priv *priv)
+{
+ u32 tcqcr;
+
+ regmap_read(priv->regs, MX25_ADCQ_CR, &tcqcr);
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FRST,
+ MX25_ADCQ_CR_FRST);
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_FRST, 0);
+ regmap_write(priv->regs, MX25_ADCQ_CR, tcqcr);
+}
+
+static void mx25_tcq_re_enable_touch_detection(struct mx25_tcq_priv *priv)
+{
+ /* stop the queue from looping */
+ mx25_tcq_force_queue_stop(priv);
+
+ /* for a clean touch detection, preload the X plane */
+ regmap_write(priv->core_regs, MX25_TSC_TICR, MX25_PRECHARGE_VALUE);
+
+ /* waste some time now to pre-load the X plate to high voltage */
+ mx25_tcq_fifo_reset(priv);
+
+ /* re-enable the detection right now */
+ regmap_write(priv->core_regs, MX25_TSC_TICR,
+ MX25_TOUCH_DETECT_VALUE | MX25_ADCQ_CFG_IGS);
+
+ regmap_update_bits(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_PD,
+ MX25_ADCQ_SR_PD);
+
+ /* enable the pen down event to be a source for the interrupt */
+ regmap_update_bits(priv->regs, MX25_ADCQ_MR, MX25_ADCQ_MR_PD_IRQ, 0);
+
+ /* lets fire the next IRQ if someone touches the touchscreen */
+ mx25_tcq_enable_touch_irq(priv);
+}
+
+static void mx25_tcq_create_event_for_4wire(struct mx25_tcq_priv *priv,
+ u32 *sample_buf,
+ unsigned int samples)
+{
+ unsigned int x_pos = 0;
+ unsigned int y_pos = 0;
+ unsigned int touch_pre = 0;
+ unsigned int touch_post = 0;
+ unsigned int i;
+
+ for (i = 0; i < samples; i++) {
+ unsigned int index = MX25_ADCQ_FIFO_ID(sample_buf[i]);
+ unsigned int val = MX25_ADCQ_FIFO_DATA(sample_buf[i]);
+
+ switch (index) {
+ case 1:
+ touch_pre = val;
+ break;
+ case 2:
+ x_pos = val;
+ break;
+ case 3:
+ y_pos = val;
+ break;
+ case 5:
+ touch_post = val;
+ break;
+ default:
+ dev_dbg(priv->dev, "Dropped samples because of invalid index %d\n",
+ index);
+ return;
+ }
+ }
+
+ if (samples != 0) {
+ /*
+ * only if both touch measures are below a threshold,
+ * the position is valid
+ */
+ if (touch_pre < priv->pen_threshold &&
+ touch_post < priv->pen_threshold) {
+ /* valid samples, generate a report */
+ x_pos /= priv->sample_count;
+ y_pos /= priv->sample_count;
+ input_report_abs(priv->idev, ABS_X, x_pos);
+ input_report_abs(priv->idev, ABS_Y, y_pos);
+ input_report_key(priv->idev, BTN_TOUCH, 1);
+ input_sync(priv->idev);
+
+ /* get next sample */
+ mx25_tcq_enable_fifo_irq(priv);
+ } else if (touch_pre >= priv->pen_threshold &&
+ touch_post >= priv->pen_threshold) {
+ /*
+ * if both samples are invalid,
+ * generate a release report
+ */
+ input_report_key(priv->idev, BTN_TOUCH, 0);
+ input_sync(priv->idev);
+ mx25_tcq_re_enable_touch_detection(priv);
+ } else {
+ /*
+ * if only one of both touch measurements are
+ * below the threshold, still some bouncing
+ * happens. Take additional samples in this
+ * case to be sure
+ */
+ mx25_tcq_enable_fifo_irq(priv);
+ }
+ }
+}
+
+static irqreturn_t mx25_tcq_irq_thread(int irq, void *dev_id)
+{
+ struct mx25_tcq_priv *priv = dev_id;
+ u32 sample_buf[TSC_MAX_SAMPLES];
+ unsigned int samples;
+ u32 stats;
+ unsigned int i;
+
+ /*
+ * Check how many samples are available. We always have to read exactly
+ * sample_count samples from the fifo, or a multiple of sample_count.
+ * Otherwise we mixup samples into different touch events.
+ */
+ regmap_read(priv->regs, MX25_ADCQ_SR, &stats);
+ samples = MX25_ADCQ_SR_FDN(stats);
+ samples -= samples % priv->sample_count;
+
+ if (!samples)
+ return IRQ_HANDLED;
+
+ for (i = 0; i != samples; ++i)
+ regmap_read(priv->regs, MX25_ADCQ_FIFO, &sample_buf[i]);
+
+ mx25_tcq_create_event_for_4wire(priv, sample_buf, samples);
+
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t mx25_tcq_irq(int irq, void *dev_id)
+{
+ struct mx25_tcq_priv *priv = dev_id;
+ u32 stat;
+ int ret = IRQ_HANDLED;
+
+ regmap_read(priv->regs, MX25_ADCQ_SR, &stat);
+
+ if (stat & (MX25_ADCQ_SR_FRR | MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR))
+ mx25_tcq_re_enable_touch_detection(priv);
+
+ if (stat & MX25_ADCQ_SR_PD) {
+ mx25_tcq_disable_touch_irq(priv);
+ mx25_tcq_force_queue_start(priv);
+ mx25_tcq_enable_fifo_irq(priv);
+ }
+
+ if (stat & MX25_ADCQ_SR_FDRY) {
+ mx25_tcq_disable_fifo_irq(priv);
+ ret = IRQ_WAKE_THREAD;
+ }
+
+ regmap_update_bits(priv->regs, MX25_ADCQ_SR, MX25_ADCQ_SR_FRR |
+ MX25_ADCQ_SR_FUR | MX25_ADCQ_SR_FOR |
+ MX25_ADCQ_SR_PD,
+ MX25_ADCQ_SR_FRR | MX25_ADCQ_SR_FUR |
+ MX25_ADCQ_SR_FOR | MX25_ADCQ_SR_PD);
+
+ return ret;
+}
+
+/* configure the state machine for a 4-wire touchscreen */
+static int mx25_tcq_init(struct mx25_tcq_priv *priv)
+{
+ u32 tgcr;
+ unsigned int ipg_div;
+ unsigned int adc_period;
+ unsigned int debounce_cnt;
+ unsigned int settling_cnt;
+ int itemct;
+ int error;
+
+ regmap_read(priv->core_regs, MX25_TSC_TGCR, &tgcr);
+ ipg_div = max_t(unsigned int, 4, MX25_TGCR_GET_ADCCLK(tgcr));
+ adc_period = USEC_PER_SEC * ipg_div * 2 + 2;
+ adc_period /= clk_get_rate(priv->clk) / 1000 + 1;
+ debounce_cnt = DIV_ROUND_UP(priv->pen_debounce, adc_period * 8) - 1;
+ settling_cnt = DIV_ROUND_UP(priv->settling_time, adc_period * 8) - 1;
+
+ /* Reset */
+ regmap_write(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_QRST | MX25_ADCQ_CR_FRST);
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_QRST | MX25_ADCQ_CR_FRST, 0);
+
+ /* up to 128 * 8 ADC clocks are possible */
+ if (debounce_cnt > 127)
+ debounce_cnt = 127;
+
+ /* up to 255 * 8 ADC clocks are possible */
+ if (settling_cnt > 255)
+ settling_cnt = 255;
+
+ error = imx25_setup_queue_4wire(priv, settling_cnt, &itemct);
+ if (error)
+ return error;
+
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_LITEMID_MASK | MX25_ADCQ_CR_WMRK_MASK,
+ MX25_ADCQ_CR_LITEMID(itemct - 1) |
+ MX25_ADCQ_CR_WMRK(priv->expected_samples - 1));
+
+ /* setup debounce count */
+ regmap_update_bits(priv->core_regs, MX25_TSC_TGCR,
+ MX25_TGCR_PDBTIME_MASK,
+ MX25_TGCR_PDBTIME(debounce_cnt));
+
+ /* enable debounce */
+ regmap_update_bits(priv->core_regs, MX25_TSC_TGCR, MX25_TGCR_PDBEN,
+ MX25_TGCR_PDBEN);
+ regmap_update_bits(priv->core_regs, MX25_TSC_TGCR, MX25_TGCR_PDEN,
+ MX25_TGCR_PDEN);
+
+ /* enable the engine on demand */
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR, MX25_ADCQ_CR_QSM_MASK,
+ MX25_ADCQ_CR_QSM_FQS);
+
+ /* Enable repeat and repeat wait */
+ regmap_update_bits(priv->regs, MX25_ADCQ_CR,
+ MX25_ADCQ_CR_RPT | MX25_ADCQ_CR_RWAIT_MASK,
+ MX25_ADCQ_CR_RPT |
+ MX25_ADCQ_CR_RWAIT(MX25_TSC_REPEAT_WAIT));
+
+ return 0;
+}
+
+static int mx25_tcq_parse_dt(struct platform_device *pdev,
+ struct mx25_tcq_priv *priv)
+{
+ struct device_node *np = pdev->dev.of_node;
+ u32 wires;
+ int error;
+
+ /* Setup defaults */
+ priv->pen_threshold = 500;
+ priv->sample_count = 3;
+ priv->pen_debounce = 1000000;
+ priv->settling_time = 250000;
+
+ error = of_property_read_u32(np, "fsl,wires", &wires);
+ if (error) {
+ dev_err(&pdev->dev, "Failed to find fsl,wires properties\n");
+ return error;
+ }
+
+ if (wires == 4) {
+ priv->mode = MX25_TS_4WIRE;
+ } else {
+ dev_err(&pdev->dev, "%u-wire mode not supported\n", wires);
+ return -EINVAL;
+ }
+
+ /* These are optional, we don't care about the return values */
+ of_property_read_u32(np, "fsl,pen-threshold", &priv->pen_threshold);
+ of_property_read_u32(np, "fsl,settling-time-ns", &priv->settling_time);
+ of_property_read_u32(np, "fsl,pen-debounce-ns", &priv->pen_debounce);
+
+ return 0;
+}
+
+static int mx25_tcq_open(struct input_dev *idev)
+{
+ struct device *dev = &idev->dev;
+ struct mx25_tcq_priv *priv = dev_get_drvdata(dev);
+ int error;
+
+ error = clk_prepare_enable(priv->clk);
+ if (error) {
+ dev_err(dev, "Failed to enable ipg clock\n");
+ return error;
+ }
+
+ error = mx25_tcq_init(priv);
+ if (error) {
+ dev_err(dev, "Failed to init tcq\n");
+ clk_disable_unprepare(priv->clk);
+ return error;
+ }
+
+ mx25_tcq_re_enable_touch_detection(priv);
+
+ return 0;
+}
+
+static void mx25_tcq_close(struct input_dev *idev)
+{
+ struct mx25_tcq_priv *priv = input_get_drvdata(idev);
+
+ mx25_tcq_force_queue_stop(priv);
+ mx25_tcq_disable_touch_irq(priv);
+ mx25_tcq_disable_fifo_irq(priv);
+ clk_disable_unprepare(priv->clk);
+}
+
+static int mx25_tcq_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct input_dev *idev;
+ struct mx25_tcq_priv *priv;
+ struct mx25_tsadc *tsadc = dev_get_drvdata(pdev->dev.parent);
+ struct resource *res;
+ void __iomem *mem;
+ int error;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+ priv->dev = dev;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ mem = devm_ioremap_resource(dev, res);
+ if (IS_ERR(mem))
+ return PTR_ERR(mem);
+
+ error = mx25_tcq_parse_dt(pdev, priv);
+ if (error)
+ return error;
+
+ priv->regs = devm_regmap_init_mmio(dev, mem, &mx25_tcq_regconfig);
+ if (IS_ERR(priv->regs)) {
+ dev_err(dev, "Failed to initialize regmap\n");
+ return PTR_ERR(priv->regs);
+ }
+
+ priv->irq = platform_get_irq(pdev, 0);
+ if (priv->irq <= 0) {
+ dev_err(dev, "Failed to get IRQ\n");
+ return priv->irq;
+ }
+
+ idev = devm_input_allocate_device(dev);
+ if (!idev) {
+ dev_err(dev, "Failed to allocate input device\n");
+ return -ENOMEM;
+ }
+
+ idev->name = mx25_tcq_name;
+ input_set_capability(idev, EV_KEY, BTN_TOUCH);
+ input_set_abs_params(idev, ABS_X, 0, 0xfff, 0, 0);
+ input_set_abs_params(idev, ABS_Y, 0, 0xfff, 0, 0);
+
+ idev->id.bustype = BUS_HOST;
+ idev->open = mx25_tcq_open;
+ idev->close = mx25_tcq_close;
+
+ priv->idev = idev;
+ input_set_drvdata(idev, priv);
+
+ priv->core_regs = tsadc->regs;
+ if (!priv->core_regs)
+ return -EINVAL;
+
+ priv->clk = tsadc->clk;
+ if (!priv->clk)
+ return -EINVAL;
+
+ platform_set_drvdata(pdev, priv);
+
+ error = devm_request_threaded_irq(dev, priv->irq, mx25_tcq_irq,
+ mx25_tcq_irq_thread, 0, pdev->name,
+ priv);
+ if (error) {
+ dev_err(dev, "Failed requesting IRQ\n");
+ return error;
+ }
+
+ error = input_register_device(idev);
+ if (error) {
+ dev_err(dev, "Failed to register input device\n");
+ return error;
+ }
+
+ return 0;
+}
+
+static struct platform_driver mx25_tcq_driver = {
+ .driver = {
+ .name = "mx25-tcq",
+ .of_match_table = mx25_tcq_ids,
+ },
+ .probe = mx25_tcq_probe,
+};
+module_platform_driver(mx25_tcq_driver);
+
+MODULE_DESCRIPTION("TS input driver for Freescale mx25");
+MODULE_AUTHOR("Markus Pargmann <mpa@pengutronix.de>");
+MODULE_LICENSE("GPL v2");
Support for the BCM590xx PMUs from Broadcom
config MFD_AXP20X
- bool "X-Powers AXP20X"
+ tristate
select MFD_CORE
- select REGMAP_I2C
select REGMAP_IRQ
- depends on I2C=y
+
+config MFD_AXP20X_I2C
+ tristate "X-Powers AXP series PMICs with I2C"
+ select MFD_AXP20X
+ select REGMAP_I2C
+ depends on I2C
+ help
+ If you say Y here you get support for the X-Powers AXP series power
+ management ICs (PMICs) controlled with I2C.
+ This driver include only the core APIs. You have to select individual
+ components like regulators or the PEK (Power Enable Key) under the
+ corresponding menus.
+
+config MFD_AXP20X_RSB
+ tristate "X-Powers AXP series PMICs with RSB"
+ select MFD_AXP20X
+ depends on SUNXI_RSB
help
- If you say Y here you get support for the X-Powers AXP202, AXP209 and
- AXP288 power management IC (PMIC).
+ If you say Y here you get support for the X-Powers AXP series power
+ management ICs (PMICs) controlled with RSB.
This driver include only the core APIs. You have to select individual
components like regulators or the PEK (Power Enable Key) under the
corresponding menus.
help
Select this if your MC13xxx is connected via an I2C bus.
+config MFD_MX25_TSADC
+ tristate "Freescale i.MX25 integrated Touchscreen and ADC unit"
+ select REGMAP_MMIO
+ depends on (SOC_IMX25 && OF) || COMPILE_TEST
+ help
+ Enable support for the integrated Touchscreen and ADC unit of the
+ i.MX25 processors. They consist of a conversion queue for general
+ purpose ADC and a queue for Touchscreens.
+
config MFD_HI6421_PMIC
tristate "HiSilicon Hi6421 PMU/Codec IC"
depends on OF
Power Management chips.
config MFD_TPS65912
- bool "TI TPS65912 Power Management chip"
- depends on GPIOLIB
+ tristate
select MFD_CORE
- help
- If you say yes here you get support for the TPS65912 series of
- PM chips.
+ select REGMAP
+ select REGMAP_IRQ
config MFD_TPS65912_I2C
- bool "TI TPS65912 Power Management chip with I2C"
- select MFD_CORE
+ tristate "TI TPS65912 Power Management chip with I2C"
select MFD_TPS65912
- depends on I2C=y && GPIOLIB
+ select REGMAP_I2C
+ depends on I2C
help
If you say yes here you get support for the TPS65912 series of
PM chips with I2C interface.
config MFD_TPS65912_SPI
- bool "TI TPS65912 Power Management chip with SPI"
- select MFD_CORE
+ tristate "TI TPS65912 Power Management chip with SPI"
select MFD_TPS65912
- depends on SPI_MASTER && GPIOLIB
+ select REGMAP_SPI
+ depends on SPI_MASTER
help
If you say yes here you get support for the TPS65912 series of
PM chips with SPI interface.
obj-$(CONFIG_MFD_TPS65217) += tps65217.o
obj-$(CONFIG_MFD_TPS65218) += tps65218.o
obj-$(CONFIG_MFD_TPS65910) += tps65910.o
-tps65912-objs := tps65912-core.o tps65912-irq.o
-obj-$(CONFIG_MFD_TPS65912) += tps65912.o
+obj-$(CONFIG_MFD_TPS65912) += tps65912-core.o
obj-$(CONFIG_MFD_TPS65912_I2C) += tps65912-i2c.o
obj-$(CONFIG_MFD_TPS65912_SPI) += tps65912-spi.o
obj-$(CONFIG_MFD_TPS80031) += tps80031.o
obj-$(CONFIG_MFD_TWL4030_AUDIO) += twl4030-audio.o
obj-$(CONFIG_TWL6040_CORE) += twl6040.o
+obj-$(CONFIG_MFD_MX25_TSADC) += fsl-imx25-tsadc.o
+
obj-$(CONFIG_MFD_MC13XXX) += mc13xxx-core.o
obj-$(CONFIG_MFD_MC13XXX_SPI) += mc13xxx-spi.o
obj-$(CONFIG_MFD_MC13XXX_I2C) += mc13xxx-i2c.o
obj-$(CONFIG_MFD_DA9052_SPI) += da9052-spi.o
obj-$(CONFIG_MFD_DA9052_I2C) += da9052-i2c.o
obj-$(CONFIG_MFD_AXP20X) += axp20x.o
+obj-$(CONFIG_MFD_AXP20X_I2C) += axp20x-i2c.o
+obj-$(CONFIG_MFD_AXP20X_RSB) += axp20x-rsb.o
obj-$(CONFIG_MFD_LP3943) += lp3943.o
obj-$(CONFIG_MFD_LP8788) += lp8788.o lp8788-irq.o
--- /dev/null
+/*
+ * I2C driver for the X-Powers' Power Management ICs
+ *
+ * AXP20x typically comprises an adaptive USB-Compatible PWM charger, BUCK DC-DC
+ * converters, LDOs, multiple 12-bit ADCs of voltage, current and temperature
+ * as well as configurable GPIOs.
+ *
+ * This driver supports the I2C variants.
+ *
+ * Copyright (C) 2014 Carlo Caione
+ *
+ * Author: Carlo Caione <carlo@caione.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/acpi.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/mfd/axp20x.h>
+#include <linux/of.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+static int axp20x_i2c_probe(struct i2c_client *i2c,
+ const struct i2c_device_id *id)
+{
+ struct axp20x_dev *axp20x;
+ int ret;
+
+ axp20x = devm_kzalloc(&i2c->dev, sizeof(*axp20x), GFP_KERNEL);
+ if (!axp20x)
+ return -ENOMEM;
+
+ axp20x->dev = &i2c->dev;
+ axp20x->irq = i2c->irq;
+ dev_set_drvdata(axp20x->dev, axp20x);
+
+ ret = axp20x_match_device(axp20x);
+ if (ret)
+ return ret;
+
+ axp20x->regmap = devm_regmap_init_i2c(i2c, axp20x->regmap_cfg);
+ if (IS_ERR(axp20x->regmap)) {
+ ret = PTR_ERR(axp20x->regmap);
+ dev_err(&i2c->dev, "regmap init failed: %d\n", ret);
+ return ret;
+ }
+
+ return axp20x_device_probe(axp20x);
+}
+
+static int axp20x_i2c_remove(struct i2c_client *i2c)
+{
+ struct axp20x_dev *axp20x = i2c_get_clientdata(i2c);
+
+ return axp20x_device_remove(axp20x);
+}
+
+static const struct of_device_id axp20x_i2c_of_match[] = {
+ { .compatible = "x-powers,axp152", .data = (void *)AXP152_ID },
+ { .compatible = "x-powers,axp202", .data = (void *)AXP202_ID },
+ { .compatible = "x-powers,axp209", .data = (void *)AXP209_ID },
+ { .compatible = "x-powers,axp221", .data = (void *)AXP221_ID },
+ { },
+};
+MODULE_DEVICE_TABLE(of, axp20x_i2c_of_match);
+
+/*
+ * This is useless for OF-enabled devices, but it is needed by I2C subsystem
+ */
+static const struct i2c_device_id axp20x_i2c_id[] = {
+ { },
+};
+MODULE_DEVICE_TABLE(i2c, axp20x_i2c_id);
+
+static const struct acpi_device_id axp20x_i2c_acpi_match[] = {
+ {
+ .id = "INT33F4",
+ .driver_data = AXP288_ID,
+ },
+ { },
+};
+MODULE_DEVICE_TABLE(acpi, axp20x_i2c_acpi_match);
+
+static struct i2c_driver axp20x_i2c_driver = {
+ .driver = {
+ .name = "axp20x-i2c",
+ .of_match_table = of_match_ptr(axp20x_i2c_of_match),
+ .acpi_match_table = ACPI_PTR(axp20x_i2c_acpi_match),
+ },
+ .probe = axp20x_i2c_probe,
+ .remove = axp20x_i2c_remove,
+ .id_table = axp20x_i2c_id,
+};
+
+module_i2c_driver(axp20x_i2c_driver);
+
+MODULE_DESCRIPTION("PMIC MFD I2C driver for AXP20X");
+MODULE_AUTHOR("Carlo Caione <carlo@caione.org>");
+MODULE_LICENSE("GPL");
--- /dev/null
+/*
+ * RSB driver for the X-Powers' Power Management ICs
+ *
+ * AXP20x typically comprises an adaptive USB-Compatible PWM charger, BUCK DC-DC
+ * converters, LDOs, multiple 12-bit ADCs of voltage, current and temperature
+ * as well as configurable GPIOs.
+ *
+ * This driver supports the RSB variants.
+ *
+ * Copyright (C) 2015 Chen-Yu Tsai
+ *
+ * Author: Chen-Yu Tsai <wens@csie.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/acpi.h>
+#include <linux/err.h>
+#include <linux/mfd/axp20x.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+#include <linux/sunxi-rsb.h>
+
+static int axp20x_rsb_probe(struct sunxi_rsb_device *rdev)
+{
+ struct axp20x_dev *axp20x;
+ int ret;
+
+ axp20x = devm_kzalloc(&rdev->dev, sizeof(*axp20x), GFP_KERNEL);
+ if (!axp20x)
+ return -ENOMEM;
+
+ axp20x->dev = &rdev->dev;
+ axp20x->irq = rdev->irq;
+ dev_set_drvdata(&rdev->dev, axp20x);
+
+ ret = axp20x_match_device(axp20x);
+ if (ret)
+ return ret;
+
+ axp20x->regmap = devm_regmap_init_sunxi_rsb(rdev, axp20x->regmap_cfg);
+ if (IS_ERR(axp20x->regmap)) {
+ ret = PTR_ERR(axp20x->regmap);
+ dev_err(&rdev->dev, "regmap init failed: %d\n", ret);
+ return ret;
+ }
+
+ return axp20x_device_probe(axp20x);
+}
+
+static int axp20x_rsb_remove(struct sunxi_rsb_device *rdev)
+{
+ struct axp20x_dev *axp20x = sunxi_rsb_device_get_drvdata(rdev);
+
+ return axp20x_device_remove(axp20x);
+}
+
+static const struct of_device_id axp20x_rsb_of_match[] = {
+ { .compatible = "x-powers,axp223", .data = (void *)AXP223_ID },
+ { },
+};
+MODULE_DEVICE_TABLE(of, axp20x_rsb_of_match);
+
+static struct sunxi_rsb_driver axp20x_rsb_driver = {
+ .driver = {
+ .name = "axp20x-rsb",
+ .of_match_table = of_match_ptr(axp20x_rsb_of_match),
+ },
+ .probe = axp20x_rsb_probe,
+ .remove = axp20x_rsb_remove,
+};
+module_sunxi_rsb_driver(axp20x_rsb_driver);
+
+MODULE_DESCRIPTION("PMIC MFD sunXi RSB driver for AXP20X");
+MODULE_AUTHOR("Chen-Yu Tsai <wens@csie.org>");
+MODULE_LICENSE("GPL v2");
/*
- * axp20x.c - MFD core driver for the X-Powers' Power Management ICs
+ * MFD core driver for the X-Powers' Power Management ICs
*
* AXP20x typically comprises an adaptive USB-Compatible PWM charger, BUCK DC-DC
* converters, LDOs, multiple 12-bit ADCs of voltage, current and temperature
* as well as configurable GPIOs.
*
+ * This file contains the interface independent core functions.
+ *
+ * Copyright (C) 2014 Carlo Caione
+ *
* Author: Carlo Caione <carlo@caione.org>
*
* This program is free software; you can redistribute it and/or modify
*/
#include <linux/err.h>
-#include <linux/i2c.h>
#include <linux/interrupt.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pm_runtime.h>
#include <linux/regmap.h>
-#include <linux/slab.h>
#include <linux/regulator/consumer.h>
#include <linux/mfd/axp20x.h>
#include <linux/mfd/core.h>
#include <linux/of_device.h>
-#include <linux/of_irq.h>
#include <linux/acpi.h>
#define AXP20X_OFF 0x80
"AXP202",
"AXP209",
"AXP221",
+ "AXP223",
"AXP288",
};
INIT_REGMAP_IRQ(AXP288, BC_USB_CHNG, 5, 1),
};
-static const struct of_device_id axp20x_of_match[] = {
- { .compatible = "x-powers,axp152", .data = (void *) AXP152_ID },
- { .compatible = "x-powers,axp202", .data = (void *) AXP202_ID },
- { .compatible = "x-powers,axp209", .data = (void *) AXP209_ID },
- { .compatible = "x-powers,axp221", .data = (void *) AXP221_ID },
- { },
-};
-MODULE_DEVICE_TABLE(of, axp20x_of_match);
-
-/*
- * This is useless for OF-enabled devices, but it is needed by I2C subsystem
- */
-static const struct i2c_device_id axp20x_i2c_id[] = {
- { },
-};
-MODULE_DEVICE_TABLE(i2c, axp20x_i2c_id);
-
-static const struct acpi_device_id axp20x_acpi_match[] = {
- {
- .id = "INT33F4",
- .driver_data = AXP288_ID,
- },
- { },
-};
-MODULE_DEVICE_TABLE(acpi, axp20x_acpi_match);
-
static const struct regmap_irq_chip axp152_regmap_irq_chip = {
.name = "axp152_irq_chip",
.status_base = AXP152_IRQ1_STATE,
AXP20X_OFF);
}
-static int axp20x_match_device(struct axp20x_dev *axp20x, struct device *dev)
+int axp20x_match_device(struct axp20x_dev *axp20x)
{
+ struct device *dev = axp20x->dev;
const struct acpi_device_id *acpi_id;
const struct of_device_id *of_id;
if (dev->of_node) {
- of_id = of_match_device(axp20x_of_match, dev);
+ of_id = of_match_device(dev->driver->of_match_table, dev);
if (!of_id) {
dev_err(dev, "Unable to match OF ID\n");
return -ENODEV;
}
- axp20x->variant = (long) of_id->data;
+ axp20x->variant = (long)of_id->data;
} else {
acpi_id = acpi_match_device(dev->driver->acpi_match_table, dev);
if (!acpi_id || !acpi_id->driver_data) {
dev_err(dev, "Unable to match ACPI ID and data\n");
return -ENODEV;
}
- axp20x->variant = (long) acpi_id->driver_data;
+ axp20x->variant = (long)acpi_id->driver_data;
}
switch (axp20x->variant) {
axp20x->regmap_irq_chip = &axp20x_regmap_irq_chip;
break;
case AXP221_ID:
+ case AXP223_ID:
axp20x->nr_cells = ARRAY_SIZE(axp22x_cells);
axp20x->cells = axp22x_cells;
axp20x->regmap_cfg = &axp22x_regmap_config;
return -EINVAL;
}
dev_info(dev, "AXP20x variant %s found\n",
- axp20x_model_names[axp20x->variant]);
+ axp20x_model_names[axp20x->variant]);
return 0;
}
+EXPORT_SYMBOL(axp20x_match_device);
-static int axp20x_i2c_probe(struct i2c_client *i2c,
- const struct i2c_device_id *id)
+int axp20x_device_probe(struct axp20x_dev *axp20x)
{
- struct axp20x_dev *axp20x;
int ret;
- axp20x = devm_kzalloc(&i2c->dev, sizeof(*axp20x), GFP_KERNEL);
- if (!axp20x)
- return -ENOMEM;
-
- ret = axp20x_match_device(axp20x, &i2c->dev);
- if (ret)
- return ret;
-
- axp20x->i2c_client = i2c;
- axp20x->dev = &i2c->dev;
- dev_set_drvdata(axp20x->dev, axp20x);
-
- axp20x->regmap = devm_regmap_init_i2c(i2c, axp20x->regmap_cfg);
- if (IS_ERR(axp20x->regmap)) {
- ret = PTR_ERR(axp20x->regmap);
- dev_err(&i2c->dev, "regmap init failed: %d\n", ret);
- return ret;
- }
-
- ret = regmap_add_irq_chip(axp20x->regmap, i2c->irq,
+ ret = regmap_add_irq_chip(axp20x->regmap, axp20x->irq,
IRQF_ONESHOT | IRQF_SHARED, -1,
axp20x->regmap_irq_chip,
&axp20x->regmap_irqc);
if (ret) {
- dev_err(&i2c->dev, "failed to add irq chip: %d\n", ret);
+ dev_err(axp20x->dev, "failed to add irq chip: %d\n", ret);
return ret;
}
ret = mfd_add_devices(axp20x->dev, -1, axp20x->cells,
- axp20x->nr_cells, NULL, 0, NULL);
+ axp20x->nr_cells, NULL, 0, NULL);
if (ret) {
- dev_err(&i2c->dev, "failed to add MFD devices: %d\n", ret);
- regmap_del_irq_chip(i2c->irq, axp20x->regmap_irqc);
+ dev_err(axp20x->dev, "failed to add MFD devices: %d\n", ret);
+ regmap_del_irq_chip(axp20x->irq, axp20x->regmap_irqc);
return ret;
}
pm_power_off = axp20x_power_off;
}
- dev_info(&i2c->dev, "AXP20X driver loaded\n");
+ dev_info(axp20x->dev, "AXP20X driver loaded\n");
return 0;
}
+EXPORT_SYMBOL(axp20x_device_probe);
-static int axp20x_i2c_remove(struct i2c_client *i2c)
+int axp20x_device_remove(struct axp20x_dev *axp20x)
{
- struct axp20x_dev *axp20x = i2c_get_clientdata(i2c);
-
if (axp20x == axp20x_pm_power_off) {
axp20x_pm_power_off = NULL;
pm_power_off = NULL;
}
mfd_remove_devices(axp20x->dev);
- regmap_del_irq_chip(axp20x->i2c_client->irq, axp20x->regmap_irqc);
+ regmap_del_irq_chip(axp20x->irq, axp20x->regmap_irqc);
return 0;
}
-
-static struct i2c_driver axp20x_i2c_driver = {
- .driver = {
- .name = "axp20x",
- .of_match_table = of_match_ptr(axp20x_of_match),
- .acpi_match_table = ACPI_PTR(axp20x_acpi_match),
- },
- .probe = axp20x_i2c_probe,
- .remove = axp20x_i2c_remove,
- .id_table = axp20x_i2c_id,
-};
-
-module_i2c_driver(axp20x_i2c_driver);
+EXPORT_SYMBOL(axp20x_device_remove);
MODULE_DESCRIPTION("PMIC MFD core driver for AXP20X");
MODULE_AUTHOR("Carlo Caione <carlo@caione.org>");
--- /dev/null
+/*
+ * Copyright (C) 2014-2015 Pengutronix, Markus Pargmann <mpa@pengutronix.de>
+ *
+ * This program is free software; you can redistribute it and/or modify it under
+ * the terms of the GNU General Public License version 2 as published by the
+ * Free Software Foundation.
+ */
+
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/irqchip/chained_irq.h>
+#include <linux/irqdesc.h>
+#include <linux/irqdomain.h>
+#include <linux/irq.h>
+#include <linux/mfd/imx25-tsadc.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+static struct regmap_config mx25_tsadc_regmap_config = {
+ .fast_io = true,
+ .max_register = 8,
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+};
+
+static void mx25_tsadc_irq_handler(struct irq_desc *desc)
+{
+ struct mx25_tsadc *tsadc = irq_desc_get_handler_data(desc);
+ struct irq_chip *chip = irq_desc_get_chip(desc);
+ u32 status;
+
+ chained_irq_enter(chip, desc);
+
+ regmap_read(tsadc->regs, MX25_TSC_TGSR, &status);
+
+ if (status & MX25_TGSR_GCQ_INT)
+ generic_handle_irq(irq_find_mapping(tsadc->domain, 1));
+
+ if (status & MX25_TGSR_TCQ_INT)
+ generic_handle_irq(irq_find_mapping(tsadc->domain, 0));
+
+ chained_irq_exit(chip, desc);
+}
+
+static int mx25_tsadc_domain_map(struct irq_domain *d, unsigned int irq,
+ irq_hw_number_t hwirq)
+{
+ struct mx25_tsadc *tsadc = d->host_data;
+
+ irq_set_chip_data(irq, tsadc);
+ irq_set_chip_and_handler(irq, &dummy_irq_chip,
+ handle_level_irq);
+ irq_modify_status(irq, IRQ_NOREQUEST, IRQ_NOPROBE);
+
+ return 0;
+}
+
+static struct irq_domain_ops mx25_tsadc_domain_ops = {
+ .map = mx25_tsadc_domain_map,
+ .xlate = irq_domain_xlate_onecell,
+};
+
+static int mx25_tsadc_setup_irq(struct platform_device *pdev,
+ struct mx25_tsadc *tsadc)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ int irq;
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq <= 0) {
+ dev_err(dev, "Failed to get irq\n");
+ return irq;
+ }
+
+ tsadc->domain = irq_domain_add_simple(np, 2, 0, &mx25_tsadc_domain_ops,
+ tsadc);
+ if (!tsadc->domain) {
+ dev_err(dev, "Failed to add irq domain\n");
+ return -ENOMEM;
+ }
+
+ irq_set_chained_handler(irq, mx25_tsadc_irq_handler);
+ irq_set_handler_data(irq, tsadc);
+
+ return 0;
+}
+
+static void mx25_tsadc_setup_clk(struct platform_device *pdev,
+ struct mx25_tsadc *tsadc)
+{
+ unsigned clk_div;
+
+ /*
+ * According to the datasheet the ADC clock should never
+ * exceed 1,75 MHz. Base clock is the IPG and the ADC unit uses
+ * a funny clock divider. To keep the ADC conversion time constant
+ * adapt the ADC internal clock divider to the IPG clock rate.
+ */
+
+ dev_dbg(&pdev->dev, "Found master clock at %lu Hz\n",
+ clk_get_rate(tsadc->clk));
+
+ clk_div = DIV_ROUND_UP(clk_get_rate(tsadc->clk), 1750000);
+ dev_dbg(&pdev->dev, "Setting up ADC clock divider to %u\n", clk_div);
+
+ /* adc clock = IPG clock / (2 * div + 2) */
+ clk_div -= 2;
+ clk_div /= 2;
+
+ /*
+ * the ADC clock divider changes its behaviour when values below 4
+ * are used: it is fixed to "/ 10" in this case
+ */
+ clk_div = max_t(unsigned, 4, clk_div);
+
+ dev_dbg(&pdev->dev, "Resulting ADC conversion clock at %lu Hz\n",
+ clk_get_rate(tsadc->clk) / (2 * clk_div + 2));
+
+ regmap_update_bits(tsadc->regs, MX25_TSC_TGCR,
+ MX25_TGCR_ADCCLKCFG(0x1f),
+ MX25_TGCR_ADCCLKCFG(clk_div));
+}
+
+static int mx25_tsadc_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ struct mx25_tsadc *tsadc;
+ struct resource *res;
+ int ret;
+ void __iomem *iomem;
+
+ tsadc = devm_kzalloc(dev, sizeof(*tsadc), GFP_KERNEL);
+ if (!tsadc)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ iomem = devm_ioremap_resource(dev, res);
+ if (IS_ERR(iomem))
+ return PTR_ERR(iomem);
+
+ tsadc->regs = devm_regmap_init_mmio(dev, iomem,
+ &mx25_tsadc_regmap_config);
+ if (IS_ERR(tsadc->regs)) {
+ dev_err(dev, "Failed to initialize regmap\n");
+ return PTR_ERR(tsadc->regs);
+ }
+
+ tsadc->clk = devm_clk_get(dev, "ipg");
+ if (IS_ERR(tsadc->clk)) {
+ dev_err(dev, "Failed to get ipg clock\n");
+ return PTR_ERR(tsadc->clk);
+ }
+
+ /* setup clock according to the datasheet */
+ mx25_tsadc_setup_clk(pdev, tsadc);
+
+ /* Enable clock and reset the component */
+ regmap_update_bits(tsadc->regs, MX25_TSC_TGCR, MX25_TGCR_CLK_EN,
+ MX25_TGCR_CLK_EN);
+ regmap_update_bits(tsadc->regs, MX25_TSC_TGCR, MX25_TGCR_TSC_RST,
+ MX25_TGCR_TSC_RST);
+
+ /* Setup powersaving mode, but enable internal reference voltage */
+ regmap_update_bits(tsadc->regs, MX25_TSC_TGCR, MX25_TGCR_POWERMODE_MASK,
+ MX25_TGCR_POWERMODE_SAVE);
+ regmap_update_bits(tsadc->regs, MX25_TSC_TGCR, MX25_TGCR_INTREFEN,
+ MX25_TGCR_INTREFEN);
+
+ ret = mx25_tsadc_setup_irq(pdev, tsadc);
+ if (ret)
+ return ret;
+
+ platform_set_drvdata(pdev, tsadc);
+
+ of_platform_populate(np, NULL, NULL, dev);
+
+ return 0;
+}
+
+static const struct of_device_id mx25_tsadc_ids[] = {
+ { .compatible = "fsl,imx25-tsadc" },
+ { /* Sentinel */ }
+};
+
+static struct platform_driver mx25_tsadc_driver = {
+ .driver = {
+ .name = "mx25-tsadc",
+ .of_match_table = of_match_ptr(mx25_tsadc_ids),
+ },
+ .probe = mx25_tsadc_probe,
+};
+module_platform_driver(mx25_tsadc_driver);
+
+MODULE_DESCRIPTION("MFD for ADC/TSC for Freescale mx25");
+MODULE_AUTHOR("Markus Pargmann <mpa@pengutronix.de>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:mx25-tsadc");
/*
- * tps65912-core.c -- TI TPS65912x
+ * Core functions for TI TPS65912x PMICs
*
- * Copyright 2011 Texas Instruments Inc.
+ * Copyright (C) 2015 Texas Instruments Incorporated - http://www.ti.com/
+ * Andrew F. Davis <afd@ti.com>
*
- * Author: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
*
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether expressed or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License version 2 for more details.
*
- * This driver is based on wm8350 implementation.
+ * Based on the TPS65218 driver and the previous TPS65912 driver by
+ * Margarita Olaya Cabrera <magi@slimlogic.co.uk>
*/
-#include <linux/module.h>
-#include <linux/moduleparam.h>
-#include <linux/slab.h>
-#include <linux/gpio.h>
+#include <linux/interrupt.h>
#include <linux/mfd/core.h>
+#include <linux/module.h>
+
#include <linux/mfd/tps65912.h>
-static const struct mfd_cell tps65912s[] = {
- {
- .name = "tps65912-pmic",
- },
+static const struct mfd_cell tps65912_cells[] = {
+ { .name = "tps65912-regulator", },
+ { .name = "tps65912-gpio", },
};
-int tps65912_set_bits(struct tps65912 *tps65912, u8 reg, u8 mask)
-{
- u8 data;
- int err;
-
- mutex_lock(&tps65912->io_mutex);
-
- err = tps65912->read(tps65912, reg, 1, &data);
- if (err) {
- dev_err(tps65912->dev, "Read from reg 0x%x failed\n", reg);
- goto out;
- }
-
- data |= mask;
- err = tps65912->write(tps65912, reg, 1, &data);
- if (err)
- dev_err(tps65912->dev, "Write to reg 0x%x failed\n", reg);
+static const struct regmap_irq tps65912_irqs[] = {
+ /* INT_STS IRQs */
+ REGMAP_IRQ_REG(TPS65912_IRQ_PWRHOLD_F, 0, TPS65912_INT_STS_PWRHOLD_F),
+ REGMAP_IRQ_REG(TPS65912_IRQ_VMON, 0, TPS65912_INT_STS_VMON),
+ REGMAP_IRQ_REG(TPS65912_IRQ_PWRON, 0, TPS65912_INT_STS_PWRON),
+ REGMAP_IRQ_REG(TPS65912_IRQ_PWRON_LP, 0, TPS65912_INT_STS_PWRON_LP),
+ REGMAP_IRQ_REG(TPS65912_IRQ_PWRHOLD_R, 0, TPS65912_INT_STS_PWRHOLD_R),
+ REGMAP_IRQ_REG(TPS65912_IRQ_HOTDIE, 0, TPS65912_INT_STS_HOTDIE),
+ REGMAP_IRQ_REG(TPS65912_IRQ_GPIO1_R, 0, TPS65912_INT_STS_GPIO1_R),
+ REGMAP_IRQ_REG(TPS65912_IRQ_GPIO1_F, 0, TPS65912_INT_STS_GPIO1_F),
+ /* INT_STS2 IRQs */
+ REGMAP_IRQ_REG(TPS65912_IRQ_GPIO2_R, 1, TPS65912_INT_STS2_GPIO2_R),
+ REGMAP_IRQ_REG(TPS65912_IRQ_GPIO2_F, 1, TPS65912_INT_STS2_GPIO2_F),
+ REGMAP_IRQ_REG(TPS65912_IRQ_GPIO3_R, 1, TPS65912_INT_STS2_GPIO3_R),
+ REGMAP_IRQ_REG(TPS65912_IRQ_GPIO3_F, 1, TPS65912_INT_STS2_GPIO3_F),
+ REGMAP_IRQ_REG(TPS65912_IRQ_GPIO4_R, 1, TPS65912_INT_STS2_GPIO4_R),
+ REGMAP_IRQ_REG(TPS65912_IRQ_GPIO4_F, 1, TPS65912_INT_STS2_GPIO4_F),
+ REGMAP_IRQ_REG(TPS65912_IRQ_GPIO5_R, 1, TPS65912_INT_STS2_GPIO5_R),
+ REGMAP_IRQ_REG(TPS65912_IRQ_GPIO5_F, 1, TPS65912_INT_STS2_GPIO5_F),
+ /* INT_STS3 IRQs */
+ REGMAP_IRQ_REG(TPS65912_IRQ_PGOOD_DCDC1, 2, TPS65912_INT_STS3_PGOOD_DCDC1),
+ REGMAP_IRQ_REG(TPS65912_IRQ_PGOOD_DCDC2, 2, TPS65912_INT_STS3_PGOOD_DCDC2),
+ REGMAP_IRQ_REG(TPS65912_IRQ_PGOOD_DCDC3, 2, TPS65912_INT_STS3_PGOOD_DCDC3),
+ REGMAP_IRQ_REG(TPS65912_IRQ_PGOOD_DCDC4, 2, TPS65912_INT_STS3_PGOOD_DCDC4),
+ REGMAP_IRQ_REG(TPS65912_IRQ_PGOOD_LDO1, 2, TPS65912_INT_STS3_PGOOD_LDO1),
+ REGMAP_IRQ_REG(TPS65912_IRQ_PGOOD_LDO2, 2, TPS65912_INT_STS3_PGOOD_LDO2),
+ REGMAP_IRQ_REG(TPS65912_IRQ_PGOOD_LDO3, 2, TPS65912_INT_STS3_PGOOD_LDO3),
+ REGMAP_IRQ_REG(TPS65912_IRQ_PGOOD_LDO4, 2, TPS65912_INT_STS3_PGOOD_LDO4),
+ /* INT_STS4 IRQs */
+ REGMAP_IRQ_REG(TPS65912_IRQ_PGOOD_LDO5, 3, TPS65912_INT_STS4_PGOOD_LDO5),
+ REGMAP_IRQ_REG(TPS65912_IRQ_PGOOD_LDO6, 3, TPS65912_INT_STS4_PGOOD_LDO6),
+ REGMAP_IRQ_REG(TPS65912_IRQ_PGOOD_LDO7, 3, TPS65912_INT_STS4_PGOOD_LDO7),
+ REGMAP_IRQ_REG(TPS65912_IRQ_PGOOD_LDO8, 3, TPS65912_INT_STS4_PGOOD_LDO8),
+ REGMAP_IRQ_REG(TPS65912_IRQ_PGOOD_LDO9, 3, TPS65912_INT_STS4_PGOOD_LDO9),
+ REGMAP_IRQ_REG(TPS65912_IRQ_PGOOD_LDO10, 3, TPS65912_INT_STS4_PGOOD_LDO10),
+};
-out:
- mutex_unlock(&tps65912->io_mutex);
- return err;
-}
-EXPORT_SYMBOL_GPL(tps65912_set_bits);
+static struct regmap_irq_chip tps65912_irq_chip = {
+ .name = "tps65912",
+ .irqs = tps65912_irqs,
+ .num_irqs = ARRAY_SIZE(tps65912_irqs),
+ .num_regs = 4,
+ .irq_reg_stride = 2,
+ .mask_base = TPS65912_INT_MSK,
+ .status_base = TPS65912_INT_STS,
+ .ack_base = TPS65912_INT_STS,
+ .init_ack_masked = true,
+};
-int tps65912_clear_bits(struct tps65912 *tps65912, u8 reg, u8 mask)
+int tps65912_device_init(struct tps65912 *tps)
{
- u8 data;
- int err;
-
- mutex_lock(&tps65912->io_mutex);
- err = tps65912->read(tps65912, reg, 1, &data);
- if (err) {
- dev_err(tps65912->dev, "Read from reg 0x%x failed\n", reg);
- goto out;
+ int ret;
+
+ ret = regmap_add_irq_chip(tps->regmap, tps->irq, IRQF_ONESHOT, 0,
+ &tps65912_irq_chip, &tps->irq_data);
+ if (ret)
+ return ret;
+
+ ret = mfd_add_devices(tps->dev, PLATFORM_DEVID_AUTO, tps65912_cells,
+ ARRAY_SIZE(tps65912_cells), NULL, 0,
+ regmap_irq_get_domain(tps->irq_data));
+ if (ret) {
+ regmap_del_irq_chip(tps->irq, tps->irq_data);
+ return ret;
}
- data &= ~mask;
- err = tps65912->write(tps65912, reg, 1, &data);
- if (err)
- dev_err(tps65912->dev, "Write to reg 0x%x failed\n", reg);
-
-out:
- mutex_unlock(&tps65912->io_mutex);
- return err;
+ return 0;
}
-EXPORT_SYMBOL_GPL(tps65912_clear_bits);
+EXPORT_SYMBOL_GPL(tps65912_device_init);
-static inline int tps65912_read(struct tps65912 *tps65912, u8 reg)
+int tps65912_device_exit(struct tps65912 *tps)
{
- u8 val;
- int err;
-
- err = tps65912->read(tps65912, reg, 1, &val);
- if (err < 0)
- return err;
-
- return val;
-}
-
-static inline int tps65912_write(struct tps65912 *tps65912, u8 reg, u8 val)
-{
- return tps65912->write(tps65912, reg, 1, &val);
-}
-
-int tps65912_reg_read(struct tps65912 *tps65912, u8 reg)
-{
- int data;
-
- mutex_lock(&tps65912->io_mutex);
+ regmap_del_irq_chip(tps->irq, tps->irq_data);
- data = tps65912_read(tps65912, reg);
- if (data < 0)
- dev_err(tps65912->dev, "Read from reg 0x%x failed\n", reg);
-
- mutex_unlock(&tps65912->io_mutex);
- return data;
-}
-EXPORT_SYMBOL_GPL(tps65912_reg_read);
-
-int tps65912_reg_write(struct tps65912 *tps65912, u8 reg, u8 val)
-{
- int err;
-
- mutex_lock(&tps65912->io_mutex);
-
- err = tps65912_write(tps65912, reg, val);
- if (err < 0)
- dev_err(tps65912->dev, "Write for reg 0x%x failed\n", reg);
-
- mutex_unlock(&tps65912->io_mutex);
- return err;
-}
-EXPORT_SYMBOL_GPL(tps65912_reg_write);
-
-int tps65912_device_init(struct tps65912 *tps65912)
-{
- struct tps65912_board *pmic_plat_data = dev_get_platdata(tps65912->dev);
- struct tps65912_platform_data *init_data;
- int ret, dcdc_avs, value;
-
- init_data = kzalloc(sizeof(struct tps65912_platform_data), GFP_KERNEL);
- if (init_data == NULL)
- return -ENOMEM;
-
- mutex_init(&tps65912->io_mutex);
- dev_set_drvdata(tps65912->dev, tps65912);
-
- dcdc_avs = (pmic_plat_data->is_dcdc1_avs << 0 |
- pmic_plat_data->is_dcdc2_avs << 1 |
- pmic_plat_data->is_dcdc3_avs << 2 |
- pmic_plat_data->is_dcdc4_avs << 3);
- if (dcdc_avs) {
- tps65912->read(tps65912, TPS65912_I2C_SPI_CFG, 1, &value);
- dcdc_avs |= value;
- tps65912->write(tps65912, TPS65912_I2C_SPI_CFG, 1, &dcdc_avs);
- }
-
- ret = mfd_add_devices(tps65912->dev, -1,
- tps65912s, ARRAY_SIZE(tps65912s),
- NULL, 0, NULL);
- if (ret < 0)
- goto err;
-
- init_data->irq = pmic_plat_data->irq;
- init_data->irq_base = pmic_plat_data->irq_base;
- ret = tps65912_irq_init(tps65912, init_data->irq, init_data);
- if (ret < 0)
- goto err;
-
- kfree(init_data);
- return ret;
-
-err:
- kfree(init_data);
- mfd_remove_devices(tps65912->dev);
- return ret;
-}
-
-void tps65912_device_exit(struct tps65912 *tps65912)
-{
- mfd_remove_devices(tps65912->dev);
- tps65912_irq_exit(tps65912);
+ return 0;
}
+EXPORT_SYMBOL_GPL(tps65912_device_exit);
-MODULE_AUTHOR("Margarita Olaya <magi@slimlogic.co.uk>");
-MODULE_DESCRIPTION("TPS65912x chip family multi-function driver");
-MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Andrew F. Davis <afd@ti.com>");
+MODULE_DESCRIPTION("TPS65912x MFD Driver");
+MODULE_LICENSE("GPL v2");
/*
- * tps65912-i2c.c -- I2C access for TI TPS65912x PMIC
+ * I2C access driver for TI TPS65912x PMICs
*
- * Copyright 2011 Texas Instruments Inc.
+ * Copyright (C) 2015 Texas Instruments Incorporated - http://www.ti.com/
+ * Andrew F. Davis <afd@ti.com>
*
- * Author: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
*
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether expressed or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License version 2 for more details.
*
- * This driver is based on wm8350 implementation.
+ * Based on the TPS65218 driver and the previous TPS65912 driver by
+ * Margarita Olaya Cabrera <magi@slimlogic.co.uk>
*/
-#include <linux/module.h>
-#include <linux/moduleparam.h>
-#include <linux/init.h>
-#include <linux/slab.h>
-#include <linux/gpio.h>
#include <linux/i2c.h>
-#include <linux/mfd/core.h>
-#include <linux/mfd/tps65912.h>
-
-static int tps65912_i2c_read(struct tps65912 *tps65912, u8 reg,
- int bytes, void *dest)
-{
- struct i2c_client *i2c = tps65912->control_data;
- struct i2c_msg xfer[2];
- int ret;
-
- /* Write register */
- xfer[0].addr = i2c->addr;
- xfer[0].flags = 0;
- xfer[0].len = 1;
- xfer[0].buf = ®
-
- /* Read data */
- xfer[1].addr = i2c->addr;
- xfer[1].flags = I2C_M_RD;
- xfer[1].len = bytes;
- xfer[1].buf = dest;
-
- ret = i2c_transfer(i2c->adapter, xfer, 2);
- if (ret == 2)
- ret = 0;
- else if (ret >= 0)
- ret = -EIO;
- return ret;
-}
-
-static int tps65912_i2c_write(struct tps65912 *tps65912, u8 reg,
- int bytes, void *src)
-{
- struct i2c_client *i2c = tps65912->control_data;
- /* we add 1 byte for device register */
- u8 msg[TPS6591X_MAX_REGISTER + 1];
- int ret;
-
- if (bytes > TPS6591X_MAX_REGISTER)
- return -EINVAL;
-
- msg[0] = reg;
- memcpy(&msg[1], src, bytes);
+#include <linux/module.h>
+#include <linux/regmap.h>
- ret = i2c_master_send(i2c, msg, bytes + 1);
- if (ret < 0)
- return ret;
- if (ret != bytes + 1)
- return -EIO;
+#include <linux/mfd/tps65912.h>
- return 0;
-}
+static const struct of_device_id tps65912_i2c_of_match_table[] = {
+ { .compatible = "ti,tps65912", },
+ { /* sentinel */ }
+};
-static int tps65912_i2c_probe(struct i2c_client *i2c,
- const struct i2c_device_id *id)
+static int tps65912_i2c_probe(struct i2c_client *client,
+ const struct i2c_device_id *ids)
{
- struct tps65912 *tps65912;
+ struct tps65912 *tps;
- tps65912 = devm_kzalloc(&i2c->dev,
- sizeof(struct tps65912), GFP_KERNEL);
- if (tps65912 == NULL)
+ tps = devm_kzalloc(&client->dev, sizeof(*tps), GFP_KERNEL);
+ if (!tps)
return -ENOMEM;
- i2c_set_clientdata(i2c, tps65912);
- tps65912->dev = &i2c->dev;
- tps65912->control_data = i2c;
- tps65912->read = tps65912_i2c_read;
- tps65912->write = tps65912_i2c_write;
+ i2c_set_clientdata(client, tps);
+ tps->dev = &client->dev;
+ tps->irq = client->irq;
+
+ tps->regmap = devm_regmap_init_i2c(client, &tps65912_regmap_config);
+ if (IS_ERR(tps->regmap)) {
+ dev_err(tps->dev, "Failed to initialize register map\n");
+ return PTR_ERR(tps->regmap);
+ }
- return tps65912_device_init(tps65912);
+ return tps65912_device_init(tps);
}
-static int tps65912_i2c_remove(struct i2c_client *i2c)
+static int tps65912_i2c_remove(struct i2c_client *client)
{
- struct tps65912 *tps65912 = i2c_get_clientdata(i2c);
+ struct tps65912 *tps = i2c_get_clientdata(client);
- tps65912_device_exit(tps65912);
-
- return 0;
+ return tps65912_device_exit(tps);
}
-static const struct i2c_device_id tps65912_i2c_id[] = {
- {"tps65912", 0 },
- { }
+static const struct i2c_device_id tps65912_i2c_id_table[] = {
+ { "tps65912", 0 },
+ { /* sentinel */ }
};
-MODULE_DEVICE_TABLE(i2c, tps65912_i2c_id);
+MODULE_DEVICE_TABLE(i2c, tps65912_i2c_id_table);
static struct i2c_driver tps65912_i2c_driver = {
- .driver = {
- .name = "tps65912",
+ .driver = {
+ .name = "tps65912",
+ .of_match_table = tps65912_i2c_of_match_table,
},
- .probe = tps65912_i2c_probe,
- .remove = tps65912_i2c_remove,
- .id_table = tps65912_i2c_id,
+ .probe = tps65912_i2c_probe,
+ .remove = tps65912_i2c_remove,
+ .id_table = tps65912_i2c_id_table,
};
+module_i2c_driver(tps65912_i2c_driver);
-static int __init tps65912_i2c_init(void)
-{
- int ret;
-
- ret = i2c_add_driver(&tps65912_i2c_driver);
- if (ret != 0)
- pr_err("Failed to register TPS65912 I2C driver: %d\n", ret);
-
- return ret;
-}
-/* init early so consumer devices can complete system boot */
-subsys_initcall(tps65912_i2c_init);
-
-static void __exit tps65912_i2c_exit(void)
-{
- i2c_del_driver(&tps65912_i2c_driver);
-}
-module_exit(tps65912_i2c_exit);
-
-MODULE_AUTHOR("Margarita Olaya <magi@slimlogic.co.uk>");
-MODULE_DESCRIPTION("TPS6591x chip family multi-function driver");
-MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Andrew F. Davis <afd@ti.com>");
+MODULE_DESCRIPTION("TPS65912x I2C Interface Driver");
+MODULE_LICENSE("GPL v2");
+++ /dev/null
-/*
- * tps65912-irq.c -- TI TPS6591x
- *
- * Copyright 2011 Texas Instruments Inc.
- *
- * Author: Margarita Olaya <magi@slimlogic.co.uk>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * This driver is based on wm8350 implementation.
- */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/bug.h>
-#include <linux/device.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/gpio.h>
-#include <linux/mfd/tps65912.h>
-
-static inline int irq_to_tps65912_irq(struct tps65912 *tps65912,
- int irq)
-{
- return irq - tps65912->irq_base;
-}
-
-/*
- * This is a threaded IRQ handler so can access I2C/SPI. Since the
- * IRQ handler explicitly clears the IRQ it handles the IRQ line
- * will be reasserted and the physical IRQ will be handled again if
- * another interrupt is asserted while we run - in the normal course
- * of events this is a rare occurrence so we save I2C/SPI reads. We're
- * also assuming that it's rare to get lots of interrupts firing
- * simultaneously so try to minimise I/O.
- */
-static irqreturn_t tps65912_irq(int irq, void *irq_data)
-{
- struct tps65912 *tps65912 = irq_data;
- u32 irq_sts;
- u32 irq_mask;
- u8 reg;
- int i;
-
-
- tps65912->read(tps65912, TPS65912_INT_STS, 1, ®);
- irq_sts = reg;
- tps65912->read(tps65912, TPS65912_INT_STS2, 1, ®);
- irq_sts |= reg << 8;
- tps65912->read(tps65912, TPS65912_INT_STS3, 1, ®);
- irq_sts |= reg << 16;
- tps65912->read(tps65912, TPS65912_INT_STS4, 1, ®);
- irq_sts |= reg << 24;
-
- tps65912->read(tps65912, TPS65912_INT_MSK, 1, ®);
- irq_mask = reg;
- tps65912->read(tps65912, TPS65912_INT_MSK2, 1, ®);
- irq_mask |= reg << 8;
- tps65912->read(tps65912, TPS65912_INT_MSK3, 1, ®);
- irq_mask |= reg << 16;
- tps65912->read(tps65912, TPS65912_INT_MSK4, 1, ®);
- irq_mask |= reg << 24;
-
- irq_sts &= ~irq_mask;
- if (!irq_sts)
- return IRQ_NONE;
-
- for (i = 0; i < tps65912->irq_num; i++) {
- if (!(irq_sts & (1 << i)))
- continue;
-
- handle_nested_irq(tps65912->irq_base + i);
- }
-
- /* Write the STS register back to clear IRQs we handled */
- reg = irq_sts & 0xFF;
- irq_sts >>= 8;
- if (reg)
- tps65912->write(tps65912, TPS65912_INT_STS, 1, ®);
- reg = irq_sts & 0xFF;
- irq_sts >>= 8;
- if (reg)
- tps65912->write(tps65912, TPS65912_INT_STS2, 1, ®);
- reg = irq_sts & 0xFF;
- irq_sts >>= 8;
- if (reg)
- tps65912->write(tps65912, TPS65912_INT_STS3, 1, ®);
- reg = irq_sts & 0xFF;
- if (reg)
- tps65912->write(tps65912, TPS65912_INT_STS4, 1, ®);
-
- return IRQ_HANDLED;
-}
-
-static void tps65912_irq_lock(struct irq_data *data)
-{
- struct tps65912 *tps65912 = irq_data_get_irq_chip_data(data);
-
- mutex_lock(&tps65912->irq_lock);
-}
-
-static void tps65912_irq_sync_unlock(struct irq_data *data)
-{
- struct tps65912 *tps65912 = irq_data_get_irq_chip_data(data);
- u32 reg_mask;
- u8 reg;
-
- tps65912->read(tps65912, TPS65912_INT_MSK, 1, ®);
- reg_mask = reg;
- tps65912->read(tps65912, TPS65912_INT_MSK2, 1, ®);
- reg_mask |= reg << 8;
- tps65912->read(tps65912, TPS65912_INT_MSK3, 1, ®);
- reg_mask |= reg << 16;
- tps65912->read(tps65912, TPS65912_INT_MSK4, 1, ®);
- reg_mask |= reg << 24;
-
- if (tps65912->irq_mask != reg_mask) {
- reg = tps65912->irq_mask & 0xFF;
- tps65912->write(tps65912, TPS65912_INT_MSK, 1, ®);
- reg = tps65912->irq_mask >> 8 & 0xFF;
- tps65912->write(tps65912, TPS65912_INT_MSK2, 1, ®);
- reg = tps65912->irq_mask >> 16 & 0xFF;
- tps65912->write(tps65912, TPS65912_INT_MSK3, 1, ®);
- reg = tps65912->irq_mask >> 24 & 0xFF;
- tps65912->write(tps65912, TPS65912_INT_MSK4, 1, ®);
- }
-
- mutex_unlock(&tps65912->irq_lock);
-}
-
-static void tps65912_irq_enable(struct irq_data *data)
-{
- struct tps65912 *tps65912 = irq_data_get_irq_chip_data(data);
-
- tps65912->irq_mask &= ~(1 << irq_to_tps65912_irq(tps65912, data->irq));
-}
-
-static void tps65912_irq_disable(struct irq_data *data)
-{
- struct tps65912 *tps65912 = irq_data_get_irq_chip_data(data);
-
- tps65912->irq_mask |= (1 << irq_to_tps65912_irq(tps65912, data->irq));
-}
-
-static struct irq_chip tps65912_irq_chip = {
- .name = "tps65912",
- .irq_bus_lock = tps65912_irq_lock,
- .irq_bus_sync_unlock = tps65912_irq_sync_unlock,
- .irq_disable = tps65912_irq_disable,
- .irq_enable = tps65912_irq_enable,
-};
-
-int tps65912_irq_init(struct tps65912 *tps65912, int irq,
- struct tps65912_platform_data *pdata)
-{
- int ret, cur_irq;
- int flags = IRQF_ONESHOT;
- u8 reg;
-
- if (!irq) {
- dev_warn(tps65912->dev, "No interrupt support, no core IRQ\n");
- return 0;
- }
-
- if (!pdata || !pdata->irq_base) {
- dev_warn(tps65912->dev, "No interrupt support, no IRQ base\n");
- return 0;
- }
-
- /* Clear unattended interrupts */
- tps65912->read(tps65912, TPS65912_INT_STS, 1, ®);
- tps65912->write(tps65912, TPS65912_INT_STS, 1, ®);
- tps65912->read(tps65912, TPS65912_INT_STS2, 1, ®);
- tps65912->write(tps65912, TPS65912_INT_STS2, 1, ®);
- tps65912->read(tps65912, TPS65912_INT_STS3, 1, ®);
- tps65912->write(tps65912, TPS65912_INT_STS3, 1, ®);
- tps65912->read(tps65912, TPS65912_INT_STS4, 1, ®);
- tps65912->write(tps65912, TPS65912_INT_STS4, 1, ®);
-
- /* Mask top level interrupts */
- tps65912->irq_mask = 0xFFFFFFFF;
-
- mutex_init(&tps65912->irq_lock);
- tps65912->chip_irq = irq;
- tps65912->irq_base = pdata->irq_base;
-
- tps65912->irq_num = TPS65912_NUM_IRQ;
-
- /* Register with genirq */
- for (cur_irq = tps65912->irq_base;
- cur_irq < tps65912->irq_num + tps65912->irq_base;
- cur_irq++) {
- irq_set_chip_data(cur_irq, tps65912);
- irq_set_chip_and_handler(cur_irq, &tps65912_irq_chip,
- handle_edge_irq);
- irq_set_nested_thread(cur_irq, 1);
- irq_clear_status_flags(cur_irq, IRQ_NOREQUEST | IRQ_NOPROBE);
- }
-
- ret = request_threaded_irq(irq, NULL, tps65912_irq, flags,
- "tps65912", tps65912);
-
- irq_set_irq_type(irq, IRQ_TYPE_LEVEL_LOW);
- if (ret != 0)
- dev_err(tps65912->dev, "Failed to request IRQ: %d\n", ret);
-
- return ret;
-}
-
-int tps65912_irq_exit(struct tps65912 *tps65912)
-{
- free_irq(tps65912->chip_irq, tps65912);
- return 0;
-}
/*
- * tps65912-spi.c -- SPI access for TI TPS65912x PMIC
+ * SPI access driver for TI TPS65912x PMICs
*
- * Copyright 2011 Texas Instruments Inc.
+ * Copyright (C) 2015 Texas Instruments Incorporated - http://www.ti.com/
+ * Andrew F. Davis <afd@ti.com>
*
- * Author: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
*
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether expressed or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License version 2 for more details.
*
- * This driver is based on wm8350 implementation.
+ * Based on the TPS65218 driver and the previous TPS65912 driver by
+ * Margarita Olaya Cabrera <magi@slimlogic.co.uk>
*/
#include <linux/module.h>
-#include <linux/moduleparam.h>
-#include <linux/init.h>
-#include <linux/slab.h>
-#include <linux/gpio.h>
+#include <linux/regmap.h>
#include <linux/spi/spi.h>
-#include <linux/mfd/core.h>
-#include <linux/mfd/tps65912.h>
-
-static int tps65912_spi_write(struct tps65912 *tps65912, u8 addr,
- int bytes, void *src)
-{
- struct spi_device *spi = tps65912->control_data;
- u8 *data = (u8 *) src;
- int ret;
- /* bit 23 is the read/write bit */
- unsigned long spi_data = 1 << 23 | addr << 15 | *data;
- struct spi_transfer xfer;
- struct spi_message msg;
- u32 tx_buf;
-
- tx_buf = spi_data;
-
- xfer.tx_buf = &tx_buf;
- xfer.rx_buf = NULL;
- xfer.len = sizeof(unsigned long);
- xfer.bits_per_word = 24;
-
- spi_message_init(&msg);
- spi_message_add_tail(&xfer, &msg);
-
- ret = spi_sync(spi, &msg);
- return ret;
-}
-
-static int tps65912_spi_read(struct tps65912 *tps65912, u8 addr,
- int bytes, void *dest)
-{
- struct spi_device *spi = tps65912->control_data;
- /* bit 23 is the read/write bit */
- unsigned long spi_data = 0 << 23 | addr << 15;
- struct spi_transfer xfer;
- struct spi_message msg;
- int ret;
- u8 *data = (u8 *) dest;
- u32 tx_buf, rx_buf;
-
- tx_buf = spi_data;
- rx_buf = 0;
- xfer.tx_buf = &tx_buf;
- xfer.rx_buf = &rx_buf;
- xfer.len = sizeof(unsigned long);
- xfer.bits_per_word = 24;
-
- spi_message_init(&msg);
- spi_message_add_tail(&xfer, &msg);
-
- if (spi == NULL)
- return 0;
+#include <linux/mfd/tps65912.h>
- ret = spi_sync(spi, &msg);
- if (ret == 0)
- *data = (u8) (rx_buf & 0xFF);
- return ret;
-}
+static const struct of_device_id tps65912_spi_of_match_table[] = {
+ { .compatible = "ti,tps65912", },
+ { /* sentinel */ }
+};
static int tps65912_spi_probe(struct spi_device *spi)
{
- struct tps65912 *tps65912;
+ struct tps65912 *tps;
- tps65912 = devm_kzalloc(&spi->dev,
- sizeof(struct tps65912), GFP_KERNEL);
- if (tps65912 == NULL)
+ tps = devm_kzalloc(&spi->dev, sizeof(*tps), GFP_KERNEL);
+ if (!tps)
return -ENOMEM;
- tps65912->dev = &spi->dev;
- tps65912->control_data = spi;
- tps65912->read = tps65912_spi_read;
- tps65912->write = tps65912_spi_write;
+ spi_set_drvdata(spi, tps);
+ tps->dev = &spi->dev;
+ tps->irq = spi->irq;
- spi_set_drvdata(spi, tps65912);
+ tps->regmap = devm_regmap_init_spi(spi, &tps65912_regmap_config);
+ if (IS_ERR(tps->regmap)) {
+ dev_err(tps->dev, "Failed to initialize register map\n");
+ return PTR_ERR(tps->regmap);
+ }
- return tps65912_device_init(tps65912);
+ return tps65912_device_init(tps);
}
-static int tps65912_spi_remove(struct spi_device *spi)
+static int tps65912_spi_remove(struct spi_device *client)
{
- struct tps65912 *tps65912 = spi_get_drvdata(spi);
+ struct tps65912 *tps = spi_get_drvdata(client);
- tps65912_device_exit(tps65912);
-
- return 0;
+ return tps65912_device_exit(tps);
}
+static const struct spi_device_id tps65912_spi_id_table[] = {
+ { "tps65912", 0 },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(spi, tps65912_spi_id_table);
+
static struct spi_driver tps65912_spi_driver = {
- .driver = {
- .name = "tps65912",
+ .driver = {
+ .name = "tps65912",
+ .of_match_table = tps65912_spi_of_match_table,
},
- .probe = tps65912_spi_probe,
- .remove = tps65912_spi_remove,
+ .probe = tps65912_spi_probe,
+ .remove = tps65912_spi_remove,
+ .id_table = tps65912_spi_id_table,
};
+module_spi_driver(tps65912_spi_driver);
-static int __init tps65912_spi_init(void)
-{
- int ret;
-
- ret = spi_register_driver(&tps65912_spi_driver);
- if (ret != 0)
- pr_err("Failed to register TPS65912 SPI driver: %d\n", ret);
-
- return 0;
-}
-/* init early so consumer devices can complete system boot */
-subsys_initcall(tps65912_spi_init);
-
-static void __exit tps65912_spi_exit(void)
-{
- spi_unregister_driver(&tps65912_spi_driver);
-}
-module_exit(tps65912_spi_exit);
-
-MODULE_AUTHOR("Margarita Olaya <magi@slimlogic.co.uk>");
-MODULE_DESCRIPTION("SPI support for TPS65912 chip family mfd");
-MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Andrew F. Davis <afd@ti.com>");
+MODULE_DESCRIPTION("TPS65912x SPI Interface Driver");
+MODULE_LICENSE("GPL v2");
config REGULATOR_TPS65912
tristate "TI TPS65912 Power regulator"
- depends on (MFD_TPS65912_I2C || MFD_TPS65912_SPI)
+ depends on MFD_TPS65912
help
This driver supports TPS65912 voltage regulator chip.
step = 75;
break;
case AXP221_ID:
+ case AXP223_ID:
min = 1800;
max = 4050;
def = 3000;
break;
case AXP221_ID:
+ case AXP223_ID:
if (id < AXP22X_DCDC1 || id > AXP22X_DCDC5)
return -EINVAL;
nregulators = AXP20X_REG_ID_MAX;
break;
case AXP221_ID:
+ case AXP223_ID:
regulators = axp22x_regulators;
nregulators = AXP22X_REG_ID_MAX;
break;
/*
- * tps65912.c -- TI tps65912
+ * Regulator driver for TI TPS65912x PMICs
*
- * Copyright 2011 Texas Instruments Inc.
+ * Copyright (C) 2015 Texas Instruments Incorporated - http://www.ti.com/
+ * Andrew F. Davis <afd@ti.com>
*
- * Author: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
*
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether expressed or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License version 2 for more details.
*
- * This driver is based on wm8350 implementation.
+ * Based on the TPS65218 driver and the previous TPS65912 driver by
+ * Margarita Olaya Cabrera <magi@slimlogic.co.uk>
*/
-#include <linux/kernel.h>
#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/err.h>
#include <linux/platform_device.h>
#include <linux/regulator/driver.h>
-#include <linux/regulator/machine.h>
-#include <linux/slab.h>
-#include <linux/gpio.h>
-#include <linux/mfd/tps65912.h>
-
-/* DCDC's */
-#define TPS65912_REG_DCDC1 0
-#define TPS65912_REG_DCDC2 1
-#define TPS65912_REG_DCDC3 2
-#define TPS65912_REG_DCDC4 3
-
-/* LDOs */
-#define TPS65912_REG_LDO1 4
-#define TPS65912_REG_LDO2 5
-#define TPS65912_REG_LDO3 6
-#define TPS65912_REG_LDO4 7
-#define TPS65912_REG_LDO5 8
-#define TPS65912_REG_LDO6 9
-#define TPS65912_REG_LDO7 10
-#define TPS65912_REG_LDO8 11
-#define TPS65912_REG_LDO9 12
-#define TPS65912_REG_LDO10 13
-
-/* Number of step-down converters available */
-#define TPS65912_NUM_DCDC 4
-
-/* Number of LDO voltage regulators available */
-#define TPS65912_NUM_LDO 10
-/* Number of total regulators available */
-#define TPS65912_NUM_REGULATOR (TPS65912_NUM_DCDC + TPS65912_NUM_LDO)
-
-#define TPS65912_REG_ENABLED 0x80
-#define OP_SELREG_MASK 0x40
-#define OP_SELREG_SHIFT 6
-
-struct tps_info {
- const char *name;
-};
+#include <linux/mfd/tps65912.h>
-static struct tps_info tps65912_regs[] = {
- {
- .name = "DCDC1",
- },
- {
- .name = "DCDC2",
- },
- {
- .name = "DCDC3",
- },
- {
- .name = "DCDC4",
- },
- {
- .name = "LDO1",
- },
- {
- .name = "LDO2",
- },
- {
- .name = "LDO3",
- },
- {
- .name = "LDO4",
- },
- {
- .name = "LDO5",
- },
- {
- .name = "LDO6",
- },
- {
- .name = "LDO7",
- },
- {
- .name = "LDO8",
- },
- {
- .name = "LDO9",
- },
- {
- .name = "LDO10",
- },
-};
+enum tps65912_regulators { DCDC1, DCDC2, DCDC3, DCDC4, LDO1, LDO2, LDO3,
+ LDO4, LDO5, LDO6, LDO7, LDO8, LDO9, LDO10 };
+
+#define TPS65912_REGULATOR(_name, _id, _of_match, _ops, _vr, _er, _lr) \
+ [_id] = { \
+ .name = _name, \
+ .of_match = _of_match, \
+ .regulators_node = "regulators", \
+ .id = _id, \
+ .ops = &_ops, \
+ .n_voltages = 64, \
+ .type = REGULATOR_VOLTAGE, \
+ .owner = THIS_MODULE, \
+ .vsel_reg = _vr, \
+ .vsel_mask = 0x3f, \
+ .enable_reg = _er, \
+ .enable_mask = BIT(7), \
+ .volt_table = NULL, \
+ .linear_ranges = _lr, \
+ .n_linear_ranges = ARRAY_SIZE(_lr), \
+ }
-struct tps65912_reg {
- struct regulator_desc desc[TPS65912_NUM_REGULATOR];
- struct tps65912 *mfd;
- struct regulator_dev *rdev[TPS65912_NUM_REGULATOR];
- struct tps_info *info[TPS65912_NUM_REGULATOR];
- /* for read/write access */
- struct mutex io_lock;
- int mode;
- int (*get_ctrl_reg)(int);
- int dcdc_range[TPS65912_NUM_DCDC];
- int pwm_mode_reg;
- int eco_reg;
+static const struct regulator_linear_range tps65912_dcdc_ranges[] = {
+ REGULATOR_LINEAR_RANGE(500000, 0x0, 0x3f, 50000),
};
static const struct regulator_linear_range tps65912_ldo_ranges[] = {
- REGULATOR_LINEAR_RANGE(800000, 0, 32, 25000),
- REGULATOR_LINEAR_RANGE(1650000, 33, 60, 50000),
- REGULATOR_LINEAR_RANGE(3100000, 61, 63, 100000),
+ REGULATOR_LINEAR_RANGE(800000, 0x0, 0x20, 25000),
+ REGULATOR_LINEAR_RANGE(1650000, 0x21, 0x3c, 50000),
+ REGULATOR_LINEAR_RANGE(3100000, 0x3d, 0x3f, 100000),
};
-static int tps65912_get_range(struct tps65912_reg *pmic, int id)
-{
- struct tps65912 *mfd = pmic->mfd;
- int range;
-
- switch (id) {
- case TPS65912_REG_DCDC1:
- range = tps65912_reg_read(mfd, TPS65912_DCDC1_LIMIT);
- break;
- case TPS65912_REG_DCDC2:
- range = tps65912_reg_read(mfd, TPS65912_DCDC2_LIMIT);
- break;
- case TPS65912_REG_DCDC3:
- range = tps65912_reg_read(mfd, TPS65912_DCDC3_LIMIT);
- break;
- case TPS65912_REG_DCDC4:
- range = tps65912_reg_read(mfd, TPS65912_DCDC4_LIMIT);
- break;
- default:
- return 0;
- }
-
- if (range >= 0)
- range = (range & DCDC_LIMIT_RANGE_MASK)
- >> DCDC_LIMIT_RANGE_SHIFT;
-
- pmic->dcdc_range[id] = range;
- return range;
-}
-
-static unsigned long tps65912_vsel_to_uv_range0(u8 vsel)
-{
- unsigned long uv;
-
- uv = ((vsel * 12500) + 500000);
- return uv;
-}
-
-static unsigned long tps65912_vsel_to_uv_range1(u8 vsel)
-{
- unsigned long uv;
-
- uv = ((vsel * 12500) + 700000);
- return uv;
-}
-
-static unsigned long tps65912_vsel_to_uv_range2(u8 vsel)
-{
- unsigned long uv;
-
- uv = ((vsel * 25000) + 500000);
- return uv;
-}
-
-static unsigned long tps65912_vsel_to_uv_range3(u8 vsel)
-{
- unsigned long uv;
-
- if (vsel == 0x3f)
- uv = 3800000;
- else
- uv = ((vsel * 50000) + 500000);
-
- return uv;
-}
-
-static int tps65912_get_ctrl_register(int id)
-{
- if (id >= TPS65912_REG_DCDC1 && id <= TPS65912_REG_LDO4)
- return id * 3 + TPS65912_DCDC1_AVS;
- else if (id >= TPS65912_REG_LDO5 && id <= TPS65912_REG_LDO10)
- return id - TPS65912_REG_LDO5 + TPS65912_LDO5;
- else
- return -EINVAL;
-}
-
-static int tps65912_get_sel_register(struct tps65912_reg *pmic, int id)
-{
- struct tps65912 *mfd = pmic->mfd;
- int opvsel;
- u8 reg = 0;
-
- if (id >= TPS65912_REG_DCDC1 && id <= TPS65912_REG_LDO4) {
- opvsel = tps65912_reg_read(mfd, id * 3 + TPS65912_DCDC1_OP);
- if (opvsel & OP_SELREG_MASK)
- reg = id * 3 + TPS65912_DCDC1_AVS;
- else
- reg = id * 3 + TPS65912_DCDC1_OP;
- } else if (id >= TPS65912_REG_LDO5 && id <= TPS65912_REG_LDO10) {
- reg = id - TPS65912_REG_LDO5 + TPS65912_LDO5;
- } else {
- return -EINVAL;
- }
-
- return reg;
-}
-
-static int tps65912_get_mode_regiters(struct tps65912_reg *pmic, int id)
-{
- switch (id) {
- case TPS65912_REG_DCDC1:
- pmic->pwm_mode_reg = TPS65912_DCDC1_CTRL;
- pmic->eco_reg = TPS65912_DCDC1_AVS;
- break;
- case TPS65912_REG_DCDC2:
- pmic->pwm_mode_reg = TPS65912_DCDC2_CTRL;
- pmic->eco_reg = TPS65912_DCDC2_AVS;
- break;
- case TPS65912_REG_DCDC3:
- pmic->pwm_mode_reg = TPS65912_DCDC3_CTRL;
- pmic->eco_reg = TPS65912_DCDC3_AVS;
- break;
- case TPS65912_REG_DCDC4:
- pmic->pwm_mode_reg = TPS65912_DCDC4_CTRL;
- pmic->eco_reg = TPS65912_DCDC4_AVS;
- break;
- default:
- return -EINVAL;
- }
-
- return 0;
-}
-
-static int tps65912_reg_is_enabled(struct regulator_dev *dev)
-{
- struct tps65912_reg *pmic = rdev_get_drvdata(dev);
- struct tps65912 *mfd = pmic->mfd;
- int reg, value, id = rdev_get_id(dev);
-
- if (id < TPS65912_REG_DCDC1 || id > TPS65912_REG_LDO10)
- return -EINVAL;
-
- reg = pmic->get_ctrl_reg(id);
- if (reg < 0)
- return reg;
-
- value = tps65912_reg_read(mfd, reg);
- if (value < 0)
- return value;
-
- return value & TPS65912_REG_ENABLED;
-}
-
-static int tps65912_reg_enable(struct regulator_dev *dev)
-{
- struct tps65912_reg *pmic = rdev_get_drvdata(dev);
- struct tps65912 *mfd = pmic->mfd;
- int id = rdev_get_id(dev);
- int reg;
-
- if (id < TPS65912_REG_DCDC1 || id > TPS65912_REG_LDO10)
- return -EINVAL;
-
- reg = pmic->get_ctrl_reg(id);
- if (reg < 0)
- return reg;
-
- return tps65912_set_bits(mfd, reg, TPS65912_REG_ENABLED);
-}
-
-static int tps65912_reg_disable(struct regulator_dev *dev)
-{
- struct tps65912_reg *pmic = rdev_get_drvdata(dev);
- struct tps65912 *mfd = pmic->mfd;
- int id = rdev_get_id(dev), reg;
-
- reg = pmic->get_ctrl_reg(id);
- if (reg < 0)
- return reg;
-
- return tps65912_clear_bits(mfd, reg, TPS65912_REG_ENABLED);
-}
-
-static int tps65912_set_mode(struct regulator_dev *dev, unsigned int mode)
-{
- struct tps65912_reg *pmic = rdev_get_drvdata(dev);
- struct tps65912 *mfd = pmic->mfd;
- int pwm_mode, eco, id = rdev_get_id(dev);
-
- tps65912_get_mode_regiters(pmic, id);
-
- pwm_mode = tps65912_reg_read(mfd, pmic->pwm_mode_reg);
- eco = tps65912_reg_read(mfd, pmic->eco_reg);
-
- pwm_mode &= DCDCCTRL_DCDC_MODE_MASK;
- eco &= DCDC_AVS_ECO_MASK;
-
- switch (mode) {
- case REGULATOR_MODE_FAST:
- /* Verify if mode alredy set */
- if (pwm_mode && !eco)
- break;
- tps65912_set_bits(mfd, pmic->pwm_mode_reg, DCDCCTRL_DCDC_MODE_MASK);
- tps65912_clear_bits(mfd, pmic->eco_reg, DCDC_AVS_ECO_MASK);
- break;
- case REGULATOR_MODE_NORMAL:
- case REGULATOR_MODE_IDLE:
- if (!pwm_mode && !eco)
- break;
- tps65912_clear_bits(mfd, pmic->pwm_mode_reg, DCDCCTRL_DCDC_MODE_MASK);
- tps65912_clear_bits(mfd, pmic->eco_reg, DCDC_AVS_ECO_MASK);
- break;
- case REGULATOR_MODE_STANDBY:
- if (!pwm_mode && eco)
- break;
- tps65912_clear_bits(mfd, pmic->pwm_mode_reg, DCDCCTRL_DCDC_MODE_MASK);
- tps65912_set_bits(mfd, pmic->eco_reg, DCDC_AVS_ECO_MASK);
- break;
- default:
- return -EINVAL;
- }
-
- return 0;
-}
-
-static unsigned int tps65912_get_mode(struct regulator_dev *dev)
-{
- struct tps65912_reg *pmic = rdev_get_drvdata(dev);
- struct tps65912 *mfd = pmic->mfd;
- int pwm_mode, eco, mode = 0, id = rdev_get_id(dev);
-
- tps65912_get_mode_regiters(pmic, id);
-
- pwm_mode = tps65912_reg_read(mfd, pmic->pwm_mode_reg);
- eco = tps65912_reg_read(mfd, pmic->eco_reg);
-
- pwm_mode &= DCDCCTRL_DCDC_MODE_MASK;
- eco &= DCDC_AVS_ECO_MASK;
-
- if (pwm_mode && !eco)
- mode = REGULATOR_MODE_FAST;
- else if (!pwm_mode && !eco)
- mode = REGULATOR_MODE_NORMAL;
- else if (!pwm_mode && eco)
- mode = REGULATOR_MODE_STANDBY;
-
- return mode;
-}
-
-static int tps65912_list_voltage(struct regulator_dev *dev, unsigned selector)
-{
- struct tps65912_reg *pmic = rdev_get_drvdata(dev);
- int range, voltage = 0, id = rdev_get_id(dev);
-
- if (id > TPS65912_REG_DCDC4)
- return -EINVAL;
-
- range = pmic->dcdc_range[id];
-
- switch (range) {
- case 0:
- /* 0.5 - 1.2875V in 12.5mV steps */
- voltage = tps65912_vsel_to_uv_range0(selector);
- break;
- case 1:
- /* 0.7 - 1.4875V in 12.5mV steps */
- voltage = tps65912_vsel_to_uv_range1(selector);
- break;
- case 2:
- /* 0.5 - 2.075V in 25mV steps */
- voltage = tps65912_vsel_to_uv_range2(selector);
- break;
- case 3:
- /* 0.5 - 3.8V in 50mV steps */
- voltage = tps65912_vsel_to_uv_range3(selector);
- break;
- }
- return voltage;
-}
-
-static int tps65912_get_voltage_sel(struct regulator_dev *dev)
-{
- struct tps65912_reg *pmic = rdev_get_drvdata(dev);
- struct tps65912 *mfd = pmic->mfd;
- int id = rdev_get_id(dev);
- int reg, vsel;
-
- reg = tps65912_get_sel_register(pmic, id);
- if (reg < 0)
- return reg;
-
- vsel = tps65912_reg_read(mfd, reg);
- vsel &= 0x3F;
-
- return vsel;
-}
-
-static int tps65912_set_voltage_sel(struct regulator_dev *dev,
- unsigned selector)
-{
- struct tps65912_reg *pmic = rdev_get_drvdata(dev);
- struct tps65912 *mfd = pmic->mfd;
- int id = rdev_get_id(dev);
- int value;
- u8 reg;
-
- reg = tps65912_get_sel_register(pmic, id);
- value = tps65912_reg_read(mfd, reg);
- value &= 0xC0;
- return tps65912_reg_write(mfd, reg, selector | value);
-}
-
/* Operations permitted on DCDCx */
static struct regulator_ops tps65912_ops_dcdc = {
- .is_enabled = tps65912_reg_is_enabled,
- .enable = tps65912_reg_enable,
- .disable = tps65912_reg_disable,
- .set_mode = tps65912_set_mode,
- .get_mode = tps65912_get_mode,
- .get_voltage_sel = tps65912_get_voltage_sel,
- .set_voltage_sel = tps65912_set_voltage_sel,
- .list_voltage = tps65912_list_voltage,
+ .is_enabled = regulator_is_enabled_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .list_voltage = regulator_list_voltage_linear_range,
};
/* Operations permitted on LDOx */
static struct regulator_ops tps65912_ops_ldo = {
- .is_enabled = tps65912_reg_is_enabled,
- .enable = tps65912_reg_enable,
- .disable = tps65912_reg_disable,
- .get_voltage_sel = tps65912_get_voltage_sel,
- .set_voltage_sel = tps65912_set_voltage_sel,
- .list_voltage = regulator_list_voltage_linear_range,
- .map_voltage = regulator_map_voltage_linear_range,
+ .is_enabled = regulator_is_enabled_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+};
+
+static const struct regulator_desc regulators[] = {
+ TPS65912_REGULATOR("DCDC1", DCDC1, "dcdc1", tps65912_ops_dcdc,
+ TPS65912_DCDC1_OP, TPS65912_DCDC1_CTRL,
+ tps65912_dcdc_ranges),
+ TPS65912_REGULATOR("DCDC2", DCDC2, "dcdc2", tps65912_ops_dcdc,
+ TPS65912_DCDC2_OP, TPS65912_DCDC2_CTRL,
+ tps65912_dcdc_ranges),
+ TPS65912_REGULATOR("DCDC3", DCDC3, "dcdc3", tps65912_ops_dcdc,
+ TPS65912_DCDC3_OP, TPS65912_DCDC3_CTRL,
+ tps65912_dcdc_ranges),
+ TPS65912_REGULATOR("DCDC4", DCDC4, "dcdc4", tps65912_ops_dcdc,
+ TPS65912_DCDC4_OP, TPS65912_DCDC4_CTRL,
+ tps65912_dcdc_ranges),
+ TPS65912_REGULATOR("LDO1", LDO1, "ldo1", tps65912_ops_ldo,
+ TPS65912_LDO1_OP, TPS65912_LDO1_AVS,
+ tps65912_ldo_ranges),
+ TPS65912_REGULATOR("LDO2", LDO2, "ldo2", tps65912_ops_ldo,
+ TPS65912_LDO2_OP, TPS65912_LDO2_AVS,
+ tps65912_ldo_ranges),
+ TPS65912_REGULATOR("LDO3", LDO3, "ldo3", tps65912_ops_ldo,
+ TPS65912_LDO3_OP, TPS65912_LDO3_AVS,
+ tps65912_ldo_ranges),
+ TPS65912_REGULATOR("LDO4", LDO4, "ldo4", tps65912_ops_ldo,
+ TPS65912_LDO4_OP, TPS65912_LDO4_AVS,
+ tps65912_ldo_ranges),
+ TPS65912_REGULATOR("LDO5", LDO5, "ldo5", tps65912_ops_ldo,
+ TPS65912_LDO5, TPS65912_LDO5,
+ tps65912_ldo_ranges),
+ TPS65912_REGULATOR("LDO6", LDO6, "ldo6", tps65912_ops_ldo,
+ TPS65912_LDO6, TPS65912_LDO6,
+ tps65912_ldo_ranges),
+ TPS65912_REGULATOR("LDO7", LDO7, "ldo7", tps65912_ops_ldo,
+ TPS65912_LDO7, TPS65912_LDO7,
+ tps65912_ldo_ranges),
+ TPS65912_REGULATOR("LDO8", LDO8, "ldo8", tps65912_ops_ldo,
+ TPS65912_LDO8, TPS65912_LDO8,
+ tps65912_ldo_ranges),
+ TPS65912_REGULATOR("LDO9", LDO9, "ldo9", tps65912_ops_ldo,
+ TPS65912_LDO9, TPS65912_LDO9,
+ tps65912_ldo_ranges),
+ TPS65912_REGULATOR("LDO10", LDO10, "ldo10", tps65912_ops_ldo,
+ TPS65912_LDO10, TPS65912_LDO10,
+ tps65912_ldo_ranges),
};
-static int tps65912_probe(struct platform_device *pdev)
+static int tps65912_regulator_probe(struct platform_device *pdev)
{
- struct tps65912 *tps65912 = dev_get_drvdata(pdev->dev.parent);
+ struct tps65912 *tps = dev_get_drvdata(pdev->dev.parent);
struct regulator_config config = { };
- struct tps_info *info;
- struct regulator_init_data *reg_data;
struct regulator_dev *rdev;
- struct tps65912_reg *pmic;
- struct tps65912_board *pmic_plat_data;
int i;
- pmic_plat_data = dev_get_platdata(tps65912->dev);
- if (!pmic_plat_data)
- return -EINVAL;
+ platform_set_drvdata(pdev, tps);
- reg_data = pmic_plat_data->tps65912_pmic_init_data;
+ config.dev = &pdev->dev;
+ config.driver_data = tps;
+ config.dev->of_node = tps->dev->of_node;
+ config.regmap = tps->regmap;
- pmic = devm_kzalloc(&pdev->dev, sizeof(*pmic), GFP_KERNEL);
- if (!pmic)
- return -ENOMEM;
-
- mutex_init(&pmic->io_lock);
- pmic->mfd = tps65912;
- platform_set_drvdata(pdev, pmic);
-
- pmic->get_ctrl_reg = &tps65912_get_ctrl_register;
- info = tps65912_regs;
-
- for (i = 0; i < TPS65912_NUM_REGULATOR; i++, info++, reg_data++) {
- int range = 0;
- /* Register the regulators */
- pmic->info[i] = info;
-
- pmic->desc[i].name = info->name;
- pmic->desc[i].id = i;
- pmic->desc[i].n_voltages = 64;
- if (i > TPS65912_REG_DCDC4) {
- pmic->desc[i].ops = &tps65912_ops_ldo;
- pmic->desc[i].linear_ranges = tps65912_ldo_ranges;
- pmic->desc[i].n_linear_ranges =
- ARRAY_SIZE(tps65912_ldo_ranges);
- } else {
- pmic->desc[i].ops = &tps65912_ops_dcdc;
- }
- pmic->desc[i].type = REGULATOR_VOLTAGE;
- pmic->desc[i].owner = THIS_MODULE;
- range = tps65912_get_range(pmic, i);
-
- config.dev = tps65912->dev;
- config.init_data = reg_data;
- config.driver_data = pmic;
-
- rdev = devm_regulator_register(&pdev->dev, &pmic->desc[i],
+ for (i = 0; i < ARRAY_SIZE(regulators); i++) {
+ rdev = devm_regulator_register(&pdev->dev, ®ulators[i],
&config);
if (IS_ERR(rdev)) {
- dev_err(tps65912->dev,
- "failed to register %s regulator\n",
+ dev_err(tps->dev, "failed to register %s regulator\n",
pdev->name);
return PTR_ERR(rdev);
}
-
- /* Save regulator for cleanup */
- pmic->rdev[i] = rdev;
}
+
return 0;
}
-static struct platform_driver tps65912_driver = {
+static const struct platform_device_id tps65912_regulator_id_table[] = {
+ { "tps65912-regulator", },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(platform, tps65912_regulator_id_table);
+
+static struct platform_driver tps65912_regulator_driver = {
.driver = {
- .name = "tps65912-pmic",
+ .name = "tps65912-regulator",
},
- .probe = tps65912_probe,
+ .probe = tps65912_regulator_probe,
+ .id_table = tps65912_regulator_id_table,
};
+module_platform_driver(tps65912_regulator_driver);
-static int __init tps65912_init(void)
-{
- return platform_driver_register(&tps65912_driver);
-}
-subsys_initcall(tps65912_init);
-
-static void __exit tps65912_cleanup(void)
-{
- platform_driver_unregister(&tps65912_driver);
-}
-module_exit(tps65912_cleanup);
-
-MODULE_AUTHOR("Margarita Olaya Cabrera <magi@slimlogic.co.uk>");
+MODULE_AUTHOR("Andrew F. Davis <afd@ti.com>");
MODULE_DESCRIPTION("TPS65912 voltage regulator driver");
MODULE_LICENSE("GPL v2");
-MODULE_ALIAS("platform:tps65912-pmic");
--- /dev/null
+/*
+ * This header provides constants for configuring the I.MX25 ADC
+ */
+
+#ifndef _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
+#define _DT_BINDINGS_IIO_ADC_FS_IMX25_GCQ_H
+
+#define MX25_ADC_REFP_YP 0 /* YP voltage reference */
+#define MX25_ADC_REFP_XP 1 /* XP voltage reference */
+#define MX25_ADC_REFP_EXT 2 /* External voltage reference */
+#define MX25_ADC_REFP_INT 3 /* Internal voltage reference */
+
+#define MX25_ADC_REFN_XN 0 /* XN ground reference */
+#define MX25_ADC_REFN_YN 1 /* YN ground reference */
+#define MX25_ADC_REFN_NGND 2 /* Internal ground reference */
+#define MX25_ADC_REFN_NGND2 3 /* External ground reference */
+
+#endif
AXP202_ID,
AXP209_ID,
AXP221_ID,
+ AXP223_ID,
AXP288_ID,
NR_AXP20X_VARIANTS,
};
struct axp20x_dev {
struct device *dev;
- struct i2c_client *i2c_client;
+ int irq;
struct regmap *regmap;
struct regmap_irq_chip_data *regmap_irqc;
long variant;
return result;
}
+/**
+ * axp20x_match_device(): Setup axp20x variant related fields
+ *
+ * @axp20x: axp20x device to setup (.dev field must be set)
+ * @dev: device associated with this axp20x device
+ *
+ * This lets the axp20x core configure the mfd cells and register maps
+ * for later use.
+ */
+int axp20x_match_device(struct axp20x_dev *axp20x);
+
+/**
+ * axp20x_device_probe(): Probe a configured axp20x device
+ *
+ * @axp20x: axp20x device to probe (must be configured)
+ *
+ * This function lets the axp20x core register the axp20x mfd devices
+ * and irqchip. The axp20x device passed in must be fully configured
+ * with axp20x_match_device, its irq set, and regmap created.
+ */
+int axp20x_device_probe(struct axp20x_dev *axp20x);
+
+/**
+ * axp20x_device_probe(): Remove a axp20x device
+ *
+ * @axp20x: axp20x device to remove
+ *
+ * This tells the axp20x core to remove the associated mfd devices
+ */
+int axp20x_device_remove(struct axp20x_dev *axp20x);
+
#endif /* __LINUX_MFD_AXP20X_H */
--- /dev/null
+#ifndef _LINUX_INCLUDE_MFD_IMX25_TSADC_H_
+#define _LINUX_INCLUDE_MFD_IMX25_TSADC_H_
+
+struct regmap;
+struct clk;
+
+struct mx25_tsadc {
+ struct regmap *regs;
+ struct irq_domain *domain;
+ struct clk *clk;
+};
+
+#define MX25_TSC_TGCR 0x00
+#define MX25_TSC_TGSR 0x04
+#define MX25_TSC_TICR 0x08
+
+/* The same register layout for TC and GC queue */
+#define MX25_ADCQ_FIFO 0x00
+#define MX25_ADCQ_CR 0x04
+#define MX25_ADCQ_SR 0x08
+#define MX25_ADCQ_MR 0x0c
+#define MX25_ADCQ_ITEM_7_0 0x20
+#define MX25_ADCQ_ITEM_15_8 0x24
+#define MX25_ADCQ_CFG(n) (0x40 + ((n) * 0x4))
+
+#define MX25_ADCQ_MR_MASK 0xffffffff
+
+/* TGCR */
+#define MX25_TGCR_PDBTIME(x) ((x) << 25)
+#define MX25_TGCR_PDBTIME_MASK GENMASK(31, 25)
+#define MX25_TGCR_PDBEN BIT(24)
+#define MX25_TGCR_PDEN BIT(23)
+#define MX25_TGCR_ADCCLKCFG(x) ((x) << 16)
+#define MX25_TGCR_GET_ADCCLK(x) (((x) >> 16) & 0x1f)
+#define MX25_TGCR_INTREFEN BIT(10)
+#define MX25_TGCR_POWERMODE_MASK GENMASK(9, 8)
+#define MX25_TGCR_POWERMODE_SAVE (1 << 8)
+#define MX25_TGCR_POWERMODE_ON (2 << 8)
+#define MX25_TGCR_STLC BIT(5)
+#define MX25_TGCR_SLPC BIT(4)
+#define MX25_TGCR_FUNC_RST BIT(2)
+#define MX25_TGCR_TSC_RST BIT(1)
+#define MX25_TGCR_CLK_EN BIT(0)
+
+/* TGSR */
+#define MX25_TGSR_SLP_INT BIT(2)
+#define MX25_TGSR_GCQ_INT BIT(1)
+#define MX25_TGSR_TCQ_INT BIT(0)
+
+/* ADCQ_ITEM_* */
+#define _MX25_ADCQ_ITEM(item, x) ((x) << ((item) * 4))
+#define MX25_ADCQ_ITEM(item, x) ((item) >= 8 ? \
+ _MX25_ADCQ_ITEM((item) - 8, (x)) : _MX25_ADCQ_ITEM((item), (x)))
+
+/* ADCQ_FIFO (TCQFIFO and GCQFIFO) */
+#define MX25_ADCQ_FIFO_DATA(x) (((x) >> 4) & 0xfff)
+#define MX25_ADCQ_FIFO_ID(x) ((x) & 0xf)
+
+/* ADCQ_CR (TCQR and GCQR) */
+#define MX25_ADCQ_CR_PDCFG_LEVEL BIT(19)
+#define MX25_ADCQ_CR_PDMSK BIT(18)
+#define MX25_ADCQ_CR_FRST BIT(17)
+#define MX25_ADCQ_CR_QRST BIT(16)
+#define MX25_ADCQ_CR_RWAIT_MASK GENMASK(15, 12)
+#define MX25_ADCQ_CR_RWAIT(x) ((x) << 12)
+#define MX25_ADCQ_CR_WMRK_MASK GENMASK(11, 8)
+#define MX25_ADCQ_CR_WMRK(x) ((x) << 8)
+#define MX25_ADCQ_CR_LITEMID_MASK (0xf << 4)
+#define MX25_ADCQ_CR_LITEMID(x) ((x) << 4)
+#define MX25_ADCQ_CR_RPT BIT(3)
+#define MX25_ADCQ_CR_FQS BIT(2)
+#define MX25_ADCQ_CR_QSM_MASK GENMASK(1, 0)
+#define MX25_ADCQ_CR_QSM_PD 0x1
+#define MX25_ADCQ_CR_QSM_FQS 0x2
+#define MX25_ADCQ_CR_QSM_FQS_PD 0x3
+
+/* ADCQ_SR (TCQSR and GCQSR) */
+#define MX25_ADCQ_SR_FDRY BIT(15)
+#define MX25_ADCQ_SR_FULL BIT(14)
+#define MX25_ADCQ_SR_EMPT BIT(13)
+#define MX25_ADCQ_SR_FDN(x) (((x) >> 8) & 0x1f)
+#define MX25_ADCQ_SR_FRR BIT(6)
+#define MX25_ADCQ_SR_FUR BIT(5)
+#define MX25_ADCQ_SR_FOR BIT(4)
+#define MX25_ADCQ_SR_EOQ BIT(1)
+#define MX25_ADCQ_SR_PD BIT(0)
+
+/* ADCQ_MR (TCQMR and GCQMR) */
+#define MX25_ADCQ_MR_FDRY_DMA BIT(31)
+#define MX25_ADCQ_MR_FER_DMA BIT(22)
+#define MX25_ADCQ_MR_FUR_DMA BIT(21)
+#define MX25_ADCQ_MR_FOR_DMA BIT(20)
+#define MX25_ADCQ_MR_EOQ_DMA BIT(17)
+#define MX25_ADCQ_MR_PD_DMA BIT(16)
+#define MX25_ADCQ_MR_FDRY_IRQ BIT(15)
+#define MX25_ADCQ_MR_FER_IRQ BIT(6)
+#define MX25_ADCQ_MR_FUR_IRQ BIT(5)
+#define MX25_ADCQ_MR_FOR_IRQ BIT(4)
+#define MX25_ADCQ_MR_EOQ_IRQ BIT(1)
+#define MX25_ADCQ_MR_PD_IRQ BIT(0)
+
+/* ADCQ_CFG (TICR, TCC0-7,GCC0-7) */
+#define MX25_ADCQ_CFG_SETTLING_TIME(x) ((x) << 24)
+#define MX25_ADCQ_CFG_IGS (1 << 20)
+#define MX25_ADCQ_CFG_NOS_MASK GENMASK(19, 16)
+#define MX25_ADCQ_CFG_NOS(x) (((x) - 1) << 16)
+#define MX25_ADCQ_CFG_WIPER (1 << 15)
+#define MX25_ADCQ_CFG_YNLR (1 << 14)
+#define MX25_ADCQ_CFG_YPLL_HIGH (0 << 12)
+#define MX25_ADCQ_CFG_YPLL_OFF (1 << 12)
+#define MX25_ADCQ_CFG_YPLL_LOW (3 << 12)
+#define MX25_ADCQ_CFG_XNUR_HIGH (0 << 10)
+#define MX25_ADCQ_CFG_XNUR_OFF (1 << 10)
+#define MX25_ADCQ_CFG_XNUR_LOW (3 << 10)
+#define MX25_ADCQ_CFG_XPUL_HIGH (0 << 9)
+#define MX25_ADCQ_CFG_XPUL_OFF (1 << 9)
+#define MX25_ADCQ_CFG_REFP(sel) ((sel) << 7)
+#define MX25_ADCQ_CFG_REFP_YP MX25_ADCQ_CFG_REFP(0)
+#define MX25_ADCQ_CFG_REFP_XP MX25_ADCQ_CFG_REFP(1)
+#define MX25_ADCQ_CFG_REFP_EXT MX25_ADCQ_CFG_REFP(2)
+#define MX25_ADCQ_CFG_REFP_INT MX25_ADCQ_CFG_REFP(3)
+#define MX25_ADCQ_CFG_REFP_MASK GENMASK(8, 7)
+#define MX25_ADCQ_CFG_IN(sel) ((sel) << 4)
+#define MX25_ADCQ_CFG_IN_XP MX25_ADCQ_CFG_IN(0)
+#define MX25_ADCQ_CFG_IN_YP MX25_ADCQ_CFG_IN(1)
+#define MX25_ADCQ_CFG_IN_XN MX25_ADCQ_CFG_IN(2)
+#define MX25_ADCQ_CFG_IN_YN MX25_ADCQ_CFG_IN(3)
+#define MX25_ADCQ_CFG_IN_WIPER MX25_ADCQ_CFG_IN(4)
+#define MX25_ADCQ_CFG_IN_AUX0 MX25_ADCQ_CFG_IN(5)
+#define MX25_ADCQ_CFG_IN_AUX1 MX25_ADCQ_CFG_IN(6)
+#define MX25_ADCQ_CFG_IN_AUX2 MX25_ADCQ_CFG_IN(7)
+#define MX25_ADCQ_CFG_REFN(sel) ((sel) << 2)
+#define MX25_ADCQ_CFG_REFN_XN MX25_ADCQ_CFG_REFN(0)
+#define MX25_ADCQ_CFG_REFN_YN MX25_ADCQ_CFG_REFN(1)
+#define MX25_ADCQ_CFG_REFN_NGND MX25_ADCQ_CFG_REFN(2)
+#define MX25_ADCQ_CFG_REFN_NGND2 MX25_ADCQ_CFG_REFN(3)
+#define MX25_ADCQ_CFG_REFN_MASK GENMASK(3, 2)
+#define MX25_ADCQ_CFG_PENIACK (1 << 1)
+
+#endif /* _LINUX_INCLUDE_MFD_IMX25_TSADC_H_ */
/*
- * tps65912.h -- TI TPS6591x
+ * Copyright (C) 2015 Texas Instruments Incorporated - http://www.ti.com/
+ * Andrew F. Davis <afd@ti.com>
*
- * Copyright 2011 Texas Instruments Inc.
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
*
- * Author: Margarita Olaya <magi@slimlogic.co.uk>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether expressed or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License version 2 for more details.
*
+ * Based on the TPS65218 driver and the previous TPS65912 driver by
+ * Margarita Olaya Cabrera <magi@slimlogic.co.uk>
*/
#ifndef __LINUX_MFD_TPS65912_H
#define __LINUX_MFD_TPS65912_H
-/* TPS regulator type list */
-#define REGULATOR_LDO 0
-#define REGULATOR_DCDC 1
-
-/*
- * List of registers for TPS65912
- */
+#include <linux/device.h>
+#include <linux/regmap.h>
+/* List of registers for TPS65912 */
#define TPS65912_DCDC1_CTRL 0x00
#define TPS65912_DCDC2_CTRL 0x01
#define TPS65912_DCDC3_CTRL 0x02
#define TPS65912_VERNUM 0x64
#define TPS6591X_MAX_REGISTER 0x64
-/* IRQ Definitions */
-#define TPS65912_IRQ_PWRHOLD_F 0
-#define TPS65912_IRQ_VMON 1
-#define TPS65912_IRQ_PWRON 2
-#define TPS65912_IRQ_PWRON_LP 3
-#define TPS65912_IRQ_PWRHOLD_R 4
-#define TPS65912_IRQ_HOTDIE 5
-#define TPS65912_IRQ_GPIO1_R 6
-#define TPS65912_IRQ_GPIO1_F 7
-#define TPS65912_IRQ_GPIO2_R 8
-#define TPS65912_IRQ_GPIO2_F 9
-#define TPS65912_IRQ_GPIO3_R 10
-#define TPS65912_IRQ_GPIO3_F 11
-#define TPS65912_IRQ_GPIO4_R 12
-#define TPS65912_IRQ_GPIO4_F 13
-#define TPS65912_IRQ_GPIO5_R 14
-#define TPS65912_IRQ_GPIO5_F 15
-#define TPS65912_IRQ_PGOOD_DCDC1 16
-#define TPS65912_IRQ_PGOOD_DCDC2 17
-#define TPS65912_IRQ_PGOOD_DCDC3 18
-#define TPS65912_IRQ_PGOOD_DCDC4 19
-#define TPS65912_IRQ_PGOOD_LDO1 20
-#define TPS65912_IRQ_PGOOD_LDO2 21
-#define TPS65912_IRQ_PGOOD_LDO3 22
-#define TPS65912_IRQ_PGOOD_LDO4 23
-#define TPS65912_IRQ_PGOOD_LDO5 24
-#define TPS65912_IRQ_PGOOD_LDO6 25
-#define TPS65912_IRQ_PGOOD_LDO7 26
-#define TPS65912_IRQ_PGOOD_LD08 27
-#define TPS65912_IRQ_PGOOD_LDO9 28
-#define TPS65912_IRQ_PGOOD_LDO10 29
+/* INT_STS Register field definitions */
+#define TPS65912_INT_STS_PWRHOLD_F BIT(0)
+#define TPS65912_INT_STS_VMON BIT(1)
+#define TPS65912_INT_STS_PWRON BIT(2)
+#define TPS65912_INT_STS_PWRON_LP BIT(3)
+#define TPS65912_INT_STS_PWRHOLD_R BIT(4)
+#define TPS65912_INT_STS_HOTDIE BIT(5)
+#define TPS65912_INT_STS_GPIO1_R BIT(6)
+#define TPS65912_INT_STS_GPIO1_F BIT(7)
+
+/* INT_STS Register field definitions */
+#define TPS65912_INT_STS2_GPIO2_R BIT(0)
+#define TPS65912_INT_STS2_GPIO2_F BIT(1)
+#define TPS65912_INT_STS2_GPIO3_R BIT(2)
+#define TPS65912_INT_STS2_GPIO3_F BIT(3)
+#define TPS65912_INT_STS2_GPIO4_R BIT(4)
+#define TPS65912_INT_STS2_GPIO4_F BIT(5)
+#define TPS65912_INT_STS2_GPIO5_R BIT(6)
+#define TPS65912_INT_STS2_GPIO5_F BIT(7)
-#define TPS65912_NUM_IRQ 30
+/* INT_STS Register field definitions */
+#define TPS65912_INT_STS3_PGOOD_DCDC1 BIT(0)
+#define TPS65912_INT_STS3_PGOOD_DCDC2 BIT(1)
+#define TPS65912_INT_STS3_PGOOD_DCDC3 BIT(2)
+#define TPS65912_INT_STS3_PGOOD_DCDC4 BIT(3)
+#define TPS65912_INT_STS3_PGOOD_LDO1 BIT(4)
+#define TPS65912_INT_STS3_PGOOD_LDO2 BIT(5)
+#define TPS65912_INT_STS3_PGOOD_LDO3 BIT(6)
+#define TPS65912_INT_STS3_PGOOD_LDO4 BIT(7)
-/* GPIO 1 and 2 Register Definitions */
+/* INT_STS Register field definitions */
+#define TPS65912_INT_STS4_PGOOD_LDO5 BIT(0)
+#define TPS65912_INT_STS4_PGOOD_LDO6 BIT(1)
+#define TPS65912_INT_STS4_PGOOD_LDO7 BIT(2)
+#define TPS65912_INT_STS4_PGOOD_LDO8 BIT(3)
+#define TPS65912_INT_STS4_PGOOD_LDO9 BIT(4)
+#define TPS65912_INT_STS4_PGOOD_LDO10 BIT(5)
+
+/* GPIO 1 and 2 Register field definitions */
#define GPIO_SLEEP_MASK 0x80
#define GPIO_SLEEP_SHIFT 7
#define GPIO_DEB_MASK 0x10
#define GPIO_SET_MASK 0x01
#define GPIO_SET_SHIFT 0
-/* GPIO 3 Register Definitions */
+/* GPIO 3 Register field definitions */
#define GPIO3_SLEEP_MASK 0x80
#define GPIO3_SLEEP_SHIFT 7
#define GPIO3_SEL_MASK 0x40
#define GPIO3_SET_MASK 0x01
#define GPIO3_SET_SHIFT 0
-/* GPIO 4 Register Definitions */
+/* GPIO 4 Register field definitions */
#define GPIO4_SLEEP_MASK 0x80
#define GPIO4_SLEEP_SHIFT 7
#define GPIO4_SEL_MASK 0x40
#define DCDC_LIMIT_MAX_SEL_MASK 0x3F
#define DCDC_LIMIT_MAX_SEL_SHIFT 0
-/**
- * struct tps65912_board
- * Board platform dat may be used to initialize regulators.
- */
-struct tps65912_board {
- int is_dcdc1_avs;
- int is_dcdc2_avs;
- int is_dcdc3_avs;
- int is_dcdc4_avs;
- int irq;
- int irq_base;
- int gpio_base;
- struct regulator_init_data *tps65912_pmic_init_data;
+/* Define the TPS65912 IRQ numbers */
+enum tps65912_irqs {
+ /* INT_STS registers */
+ TPS65912_IRQ_PWRHOLD_F,
+ TPS65912_IRQ_VMON,
+ TPS65912_IRQ_PWRON,
+ TPS65912_IRQ_PWRON_LP,
+ TPS65912_IRQ_PWRHOLD_R,
+ TPS65912_IRQ_HOTDIE,
+ TPS65912_IRQ_GPIO1_R,
+ TPS65912_IRQ_GPIO1_F,
+ /* INT_STS2 registers */
+ TPS65912_IRQ_GPIO2_R,
+ TPS65912_IRQ_GPIO2_F,
+ TPS65912_IRQ_GPIO3_R,
+ TPS65912_IRQ_GPIO3_F,
+ TPS65912_IRQ_GPIO4_R,
+ TPS65912_IRQ_GPIO4_F,
+ TPS65912_IRQ_GPIO5_R,
+ TPS65912_IRQ_GPIO5_F,
+ /* INT_STS3 registers */
+ TPS65912_IRQ_PGOOD_DCDC1,
+ TPS65912_IRQ_PGOOD_DCDC2,
+ TPS65912_IRQ_PGOOD_DCDC3,
+ TPS65912_IRQ_PGOOD_DCDC4,
+ TPS65912_IRQ_PGOOD_LDO1,
+ TPS65912_IRQ_PGOOD_LDO2,
+ TPS65912_IRQ_PGOOD_LDO3,
+ TPS65912_IRQ_PGOOD_LDO4,
+ /* INT_STS4 registers */
+ TPS65912_IRQ_PGOOD_LDO5,
+ TPS65912_IRQ_PGOOD_LDO6,
+ TPS65912_IRQ_PGOOD_LDO7,
+ TPS65912_IRQ_PGOOD_LDO8,
+ TPS65912_IRQ_PGOOD_LDO9,
+ TPS65912_IRQ_PGOOD_LDO10,
};
-/**
- * struct tps65912 - tps65912 sub-driver chip access routines
+/*
+ * struct tps65912 - state holder for the tps65912 driver
+ *
+ * Device data may be used to access the TPS65912 chip
*/
-
struct tps65912 {
struct device *dev;
- /* for read/write acces */
- struct mutex io_mutex;
-
- /* For device IO interfaces: I2C or SPI */
- void *control_data;
-
- int (*read)(struct tps65912 *tps65912, u8 reg, int size, void *dest);
- int (*write)(struct tps65912 *tps65912, u8 reg, int size, void *src);
-
- /* Client devices */
- struct tps65912_pmic *pmic;
+ struct regmap *regmap;
- /* GPIO Handling */
- struct gpio_chip gpio;
+ /* IRQ Data */
+ int irq;
+ struct regmap_irq_chip_data *irq_data;
+};
- /* IRQ Handling */
- struct mutex irq_lock;
- int chip_irq;
- int irq_base;
- int irq_num;
- u32 irq_mask;
+static const struct regmap_range tps65912_yes_ranges[] = {
+ regmap_reg_range(TPS65912_INT_STS, TPS65912_GPIO5),
};
-struct tps65912_platform_data {
- int irq;
- int irq_base;
+static const struct regmap_access_table tps65912_volatile_table = {
+ .yes_ranges = tps65912_yes_ranges,
+ .n_yes_ranges = ARRAY_SIZE(tps65912_yes_ranges),
};
-unsigned int tps_chip(void);
+static const struct regmap_config tps65912_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .cache_type = REGCACHE_RBTREE,
+ .volatile_table = &tps65912_volatile_table,
+};
-int tps65912_set_bits(struct tps65912 *tps65912, u8 reg, u8 mask);
-int tps65912_clear_bits(struct tps65912 *tps65912, u8 reg, u8 mask);
-int tps65912_reg_read(struct tps65912 *tps65912, u8 reg);
-int tps65912_reg_write(struct tps65912 *tps65912, u8 reg, u8 val);
-int tps65912_device_init(struct tps65912 *tps65912);
-void tps65912_device_exit(struct tps65912 *tps65912);
-int tps65912_irq_init(struct tps65912 *tps65912, int irq,
- struct tps65912_platform_data *pdata);
-int tps65912_irq_exit(struct tps65912 *tps65912);
+int tps65912_device_init(struct tps65912 *tps);
+int tps65912_device_exit(struct tps65912 *tps);
#endif /* __LINUX_MFD_TPS65912_H */
projects / cascardo / linux.git / commitdiff