dra7-evm.dtb
dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-d2-network.dtb \
orion5x-lacie-ethernet-disk-mini-v2.dtb \
+ orion5x-maxtor-shared-storage-2.dtb \
orion5x-rd88f5182-nas.dtb
dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcom-msm8660-surf.dtb \
--- /dev/null
+/*
+ * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ * Copyright (C) Sylver Bruneau <sylver.bruneau@googlemail.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "orion5x-mv88f5182.dtsi"
+
+/ {
+ model = "Maxtor Shared Storage II";
+ compatible = "maxtor,shared-storage-2", "marvell,orion5x-88f5182", "marvell,orion5x";
+
+ memory {
+ reg = <0x00000000 0x4000000>; /* 64 MB */
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ linux,stdout-path = &uart0;
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>,
+ <MBUS_ID(0x09, 0x00) 0 0xf2200000 0x800>,
+ <MBUS_ID(0x01, 0x0f) 0 0xff800000 0x40000>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&pmx_buttons>;
+ pinctrl-names = "default";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ power {
+ label = "Power";
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
+ };
+
+ reset {
+ label = "Reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&devbus_bootcs {
+ status = "okay";
+
+ devbus,keep-config;
+
+ /*
+ * Currently the MTD code does not recognize the MX29LV400CBCT
+ * as a bottom-type device. This could cause risks of
+ * accidentally erasing critical flash sectors. We thus define
+ * a single, write-protected partition covering the whole
+ * flash. TODO: once the flash part TOP/BOTTOM detection
+ * issue is sorted out in the MTD code, break this into at
+ * least three partitions: 'u-boot code', 'u-boot environment'
+ * and 'whatever is left'.
+ */
+ flash@0 {
+ compatible = "cfi-flash";
+ reg = <0 0x40000>;
+ bank-width = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy: ethernet-phy {
+ reg = <8>;
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+ð {
+ status = "okay";
+
+ ethernet-port@0 {
+ phy-handle = <ðphy>;
+ };
+};
+
+&i2c {
+ status = "okay";
+ clock-frequency = <100000>;
+ #address-cells = <1>;
+
+ rtc@68 {
+ compatible = "st,m41t81";
+ reg = <0x68>;
+ pinctrl-0 = <&pmx_rtc>;
+ pinctrl-names = "default";
+ interrupt-parent = <&gpio0>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&pinctrl {
+ pinctrl-0 = <&pmx_leds &pmx_misc>;
+ pinctrl-names = "default";
+
+ pmx_buttons: pmx-buttons {
+ marvell,pins = "mpp11", "mpp12";
+ marvell,function = "gpio";
+ };
+
+ /*
+ * MPP0: Power LED
+ * MPP1: Error LED
+ */
+ pmx_leds: pmx-leds {
+ marvell,pins = "mpp0", "mpp1";
+ marvell,function = "gpio";
+ };
+
+ /*
+ * MPP4: HDD ind. (Single/Dual)
+ * MPP5: HD0 5V control
+ * MPP6: HD0 12V control
+ * MPP7: HD1 5V control
+ * MPP8: HD1 12V control
+ */
+ pmx_misc: pmx-misc {
+ marvell,pins = "mpp4", "mpp5", "mpp6", "mpp7", "mpp8", "mpp10";
+ marvell,function = "gpio";
+ };
+
+ pmx_rtc: pmx-rtc {
+ marvell,pins = "mpp3";
+ marvell,function = "gpio";
+ };
+
+ pmx_sata0_led_active: pmx-sata0-led-active {
+ marvell,pins = "mpp14";
+ marvell,function = "sata0";
+ };
+
+ pmx_sata1_led_active: pmx-sata1-led-active {
+ marvell,pins = "mpp15";
+ marvell,function = "sata1";
+ };
+
+ /*
+ * Non MPP GPIOs:
+ * GPIO 22: USB port 1 fuse (0 = Fail, 1 = Ok)
+ * GPIO 23: Blue front LED off
+ * GPIO 24: Inhibit board power off (0 = Disabled, 1 = Enabled)
+ */
+};
+
+&sata {
+ pinctrl-0 = <&pmx_sata0_led_active
+ &pmx_sata1_led_active>;
+ pinctrl-names = "default";
+ status = "okay";
+ nr-ports = <2>;
+};
+
+&uart0 {
+ status = "okay";
+};
Say 'Y' here if you want your kernel to support the
LaCie 2Big Network NAS.
-config MACH_MSS2
- bool "Maxtor Shared Storage II"
+config MACH_MSS2_DT
+ bool "Maxtor Shared Storage II (Flattened Device Tree)"
+ select ARCH_ORION5X_DT
help
Say 'Y' here if you want your kernel to support the
Maxtor Shared Storage II platform.
obj-$(CONFIG_MACH_TS78XX) += ts78xx-setup.o
obj-$(CONFIG_MACH_MV2120) += mv2120-setup.o
obj-$(CONFIG_MACH_NET2BIG) += net2big-setup.o
-obj-$(CONFIG_MACH_MSS2) += mss2-setup.o
obj-$(CONFIG_MACH_WNR854T) += wnr854t-setup.o
obj-$(CONFIG_MACH_RD88F5181L_GE) += rd88f5181l-ge-setup.o
obj-$(CONFIG_MACH_RD88F5181L_FXO) += rd88f5181l-fxo-setup.o
obj-$(CONFIG_ARCH_ORION5X_DT) += board-dt.o
obj-$(CONFIG_MACH_D2NET_DT) += board-d2net.o
+obj-$(CONFIG_MACH_MSS2_DT) += board-mss2.o
obj-$(CONFIG_MACH_RD88F5182_DT) += board-rd88f5182.o
cpu_idle_poll_ctrl(true);
}
+ if (of_machine_is_compatible("maxtor,shared-storage-2"))
+ mss2_init();
+
of_platform_populate(NULL, of_default_bus_match_table,
orion5x_auxdata_lookup, NULL);
}
--- /dev/null
+/*
+ * Maxtor Shared Storage II Board Setup
+ *
+ * Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/pci.h>
+#include <linux/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/pci.h>
+#include <mach/orion5x.h>
+#include <mach/bridge-regs.h>
+#include "common.h"
+
+/*****************************************************************************
+ * Maxtor Shared Storage II Info
+ ****************************************************************************/
+
+/****************************************************************************
+ * PCI setup
+ ****************************************************************************/
+static int __init mss2_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+ int irq;
+
+ /*
+ * Check for devices with hard-wired IRQs.
+ */
+ irq = orion5x_pci_map_irq(dev, slot, pin);
+ if (irq != -1)
+ return irq;
+
+ return -1;
+}
+
+static struct hw_pci mss2_pci __initdata = {
+ .nr_controllers = 2,
+ .setup = orion5x_pci_sys_setup,
+ .scan = orion5x_pci_sys_scan_bus,
+ .map_irq = mss2_pci_map_irq,
+};
+
+static int __init mss2_pci_init(void)
+{
+ if (machine_is_mss2())
+ pci_common_init(&mss2_pci);
+
+ return 0;
+}
+subsys_initcall(mss2_pci_init);
+
+/*****************************************************************************
+ * MSS2 power off method
+ ****************************************************************************/
+/*
+ * On the Maxtor Shared Storage II, the shutdown process is the following :
+ * - Userland modifies U-boot env to tell U-boot to go idle at next boot
+ * - The board reboots
+ * - U-boot starts and go into an idle mode until the user press "power"
+ */
+static void mss2_power_off(void)
+{
+ u32 reg;
+
+ /*
+ * Enable and issue soft reset
+ */
+ reg = readl(RSTOUTn_MASK);
+ reg |= 1 << 2;
+ writel(reg, RSTOUTn_MASK);
+
+ reg = readl(CPU_SOFT_RESET);
+ reg |= 1;
+ writel(reg, CPU_SOFT_RESET);
+}
+
+void __init mss2_init(void)
+{
+ /* register mss2 specific power-off method */
+ pm_power_off = mss2_power_off;
+}
struct tag;
extern void __init tag_fixup_mem32(struct tag *, char **, struct meminfo *);
+#ifdef CONFIG_MACH_MSS2_DT
+extern void mss2_init(void);
+#else
+static inline void mss2_init(void) {}
+#endif
+
/*****************************************************************************
* Helpers to access Orion registers
****************************************************************************/
+++ /dev/null
-/*
- * Maxtor Shared Storage II Board Setup
- *
- * Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License
- * as published by the Free Software Foundation; either version
- * 2 of the License, or (at your option) any later version.
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/pci.h>
-#include <linux/irq.h>
-#include <linux/mtd/physmap.h>
-#include <linux/mv643xx_eth.h>
-#include <linux/leds.h>
-#include <linux/gpio_keys.h>
-#include <linux/input.h>
-#include <linux/i2c.h>
-#include <linux/ata_platform.h>
-#include <linux/gpio.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/pci.h>
-#include <mach/orion5x.h>
-#include <mach/bridge-regs.h>
-#include "common.h"
-#include "mpp.h"
-
-#define MSS2_NOR_BOOT_BASE 0xff800000
-#define MSS2_NOR_BOOT_SIZE SZ_256K
-
-/*****************************************************************************
- * Maxtor Shared Storage II Info
- ****************************************************************************/
-
-/*
- * Maxtor Shared Storage II hardware :
- * - Marvell 88F5182-A2 C500
- * - Marvell 88E1111 Gigabit Ethernet PHY
- * - RTC M41T81 (@0x68) on I2C bus
- * - 256KB NOR flash
- * - 64MB of RAM
- */
-
-/*****************************************************************************
- * 256KB NOR Flash on BOOT Device
- ****************************************************************************/
-
-static struct physmap_flash_data mss2_nor_flash_data = {
- .width = 1,
-};
-
-static struct resource mss2_nor_flash_resource = {
- .flags = IORESOURCE_MEM,
- .start = MSS2_NOR_BOOT_BASE,
- .end = MSS2_NOR_BOOT_BASE + MSS2_NOR_BOOT_SIZE - 1,
-};
-
-static struct platform_device mss2_nor_flash = {
- .name = "physmap-flash",
- .id = 0,
- .dev = {
- .platform_data = &mss2_nor_flash_data,
- },
- .resource = &mss2_nor_flash_resource,
- .num_resources = 1,
-};
-
-/****************************************************************************
- * PCI setup
- ****************************************************************************/
-static int __init mss2_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-{
- int irq;
-
- /*
- * Check for devices with hard-wired IRQs.
- */
- irq = orion5x_pci_map_irq(dev, slot, pin);
- if (irq != -1)
- return irq;
-
- return -1;
-}
-
-static struct hw_pci mss2_pci __initdata = {
- .nr_controllers = 2,
- .setup = orion5x_pci_sys_setup,
- .scan = orion5x_pci_sys_scan_bus,
- .map_irq = mss2_pci_map_irq,
-};
-
-static int __init mss2_pci_init(void)
-{
- if (machine_is_mss2())
- pci_common_init(&mss2_pci);
-
- return 0;
-}
-subsys_initcall(mss2_pci_init);
-
-
-/*****************************************************************************
- * Ethernet
- ****************************************************************************/
-
-static struct mv643xx_eth_platform_data mss2_eth_data = {
- .phy_addr = MV643XX_ETH_PHY_ADDR(8),
-};
-
-/*****************************************************************************
- * SATA
- ****************************************************************************/
-
-static struct mv_sata_platform_data mss2_sata_data = {
- .n_ports = 2,
-};
-
-/*****************************************************************************
- * GPIO buttons
- ****************************************************************************/
-
-#define MSS2_GPIO_KEY_RESET 12
-#define MSS2_GPIO_KEY_POWER 11
-
-static struct gpio_keys_button mss2_buttons[] = {
- {
- .code = KEY_POWER,
- .gpio = MSS2_GPIO_KEY_POWER,
- .desc = "Power",
- .active_low = 1,
- }, {
- .code = KEY_RESTART,
- .gpio = MSS2_GPIO_KEY_RESET,
- .desc = "Reset",
- .active_low = 1,
- },
-};
-
-static struct gpio_keys_platform_data mss2_button_data = {
- .buttons = mss2_buttons,
- .nbuttons = ARRAY_SIZE(mss2_buttons),
-};
-
-static struct platform_device mss2_button_device = {
- .name = "gpio-keys",
- .id = -1,
- .dev = {
- .platform_data = &mss2_button_data,
- },
-};
-
-/*****************************************************************************
- * RTC m41t81 on I2C bus
- ****************************************************************************/
-
-#define MSS2_GPIO_RTC_IRQ 3
-
-static struct i2c_board_info __initdata mss2_i2c_rtc = {
- I2C_BOARD_INFO("m41t81", 0x68),
-};
-
-/*****************************************************************************
- * MSS2 power off method
- ****************************************************************************/
-/*
- * On the Maxtor Shared Storage II, the shutdown process is the following :
- * - Userland modifies U-boot env to tell U-boot to go idle at next boot
- * - The board reboots
- * - U-boot starts and go into an idle mode until the user press "power"
- */
-static void mss2_power_off(void)
-{
- u32 reg;
-
- /*
- * Enable and issue soft reset
- */
- reg = readl(RSTOUTn_MASK);
- reg |= 1 << 2;
- writel(reg, RSTOUTn_MASK);
-
- reg = readl(CPU_SOFT_RESET);
- reg |= 1;
- writel(reg, CPU_SOFT_RESET);
-}
-
-/****************************************************************************
- * General Setup
- ****************************************************************************/
-static unsigned int mss2_mpp_modes[] __initdata = {
- MPP0_GPIO, /* Power LED */
- MPP1_GPIO, /* Error LED */
- MPP2_UNUSED,
- MPP3_GPIO, /* RTC interrupt */
- MPP4_GPIO, /* HDD ind. (Single/Dual)*/
- MPP5_GPIO, /* HD0 5V control */
- MPP6_GPIO, /* HD0 12V control */
- MPP7_GPIO, /* HD1 5V control */
- MPP8_GPIO, /* HD1 12V control */
- MPP9_UNUSED,
- MPP10_GPIO, /* Fan control */
- MPP11_GPIO, /* Power button */
- MPP12_GPIO, /* Reset button */
- MPP13_UNUSED,
- MPP14_SATA_LED, /* SATA 0 active */
- MPP15_SATA_LED, /* SATA 1 active */
- MPP16_UNUSED,
- MPP17_UNUSED,
- MPP18_UNUSED,
- MPP19_UNUSED,
- 0,
-};
-
-static void __init mss2_init(void)
-{
- /* Setup basic Orion functions. Need to be called early. */
- orion5x_init();
-
- orion5x_mpp_conf(mss2_mpp_modes);
-
- /*
- * MPP[20] Unused
- * MPP[21] PCI clock
- * MPP[22] USB 0 over current
- * MPP[23] USB 1 over current
- */
-
- /*
- * Configure peripherals.
- */
- orion5x_ehci0_init();
- orion5x_ehci1_init();
- orion5x_eth_init(&mss2_eth_data);
- orion5x_i2c_init();
- orion5x_sata_init(&mss2_sata_data);
- orion5x_uart0_init();
- orion5x_xor_init();
-
- mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
- ORION_MBUS_DEVBUS_BOOT_ATTR,
- MSS2_NOR_BOOT_BASE,
- MSS2_NOR_BOOT_SIZE);
- platform_device_register(&mss2_nor_flash);
-
- platform_device_register(&mss2_button_device);
-
- if (gpio_request(MSS2_GPIO_RTC_IRQ, "rtc") == 0) {
- if (gpio_direction_input(MSS2_GPIO_RTC_IRQ) == 0)
- mss2_i2c_rtc.irq = gpio_to_irq(MSS2_GPIO_RTC_IRQ);
- else
- gpio_free(MSS2_GPIO_RTC_IRQ);
- }
- i2c_register_board_info(0, &mss2_i2c_rtc, 1);
-
- /* register mss2 specific power-off method */
- pm_power_off = mss2_power_off;
-}
-
-MACHINE_START(MSS2, "Maxtor Shared Storage II")
- /* Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com> */
- .atag_offset = 0x100,
- .init_machine = mss2_init,
- .map_io = orion5x_map_io,
- .init_early = orion5x_init_early,
- .init_irq = orion5x_init_irq,
- .init_time = orion5x_timer_init,
- .fixup = tag_fixup_mem32,
- .restart = orion5x_restart,
-MACHINE_END
projects / cascardo / linux.git / commitdiff