iwlwifi: consider VHT 160MHz while parsing NVM

Devices belonging to 9000 family can support VHT 160MHz channel
width, so need to consider it when configuring VHT capabilities.
However, NVM file doesn't have a single bit specifying that 160MHz
is supported. This patch turns on 160MHz support in VHT capabilities
in case there's at least one channel supporting 160MHz.

Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

diff --git a/drivers/net/wireless/intel/iwlwifi/iwl-eeprom-parse.h b/drivers/net/wireless/intel/iwlwifi/iwl-eeprom-parse.h
index 53f39a3..1f4e502 100644 (file)
--- a/drivers/net/wireless/intel/iwlwifi/iwl-eeprom-parse.h
+++ b/drivers/net/wireless/intel/iwlwifi/iwl-eeprom-parse.h
@@ -98,6 +98,7 @@ struct iwl_nvm_data {
        s8 max_tx_pwr_half_dbm;
 
        bool lar_enabled;
+       bool vht160_supported;
        struct ieee80211_supported_band bands[NUM_NL80211_BANDS];
        struct ieee80211_channel channels[];
 };

diff --git a/drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c b/drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c
index 14743c3..b13f409 100644 (file)
--- a/drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c
+++ b/drivers/net/wireless/intel/iwlwifi/iwl-nvm-parse.c
@@ -288,6 +288,9 @@ static int iwl_init_channel_map(struct device *dev, const struct iwl_cfg *cfg,
                    !data->sku_cap_band_52GHz_enable)
                        continue;
 
+               if (ch_flags & NVM_CHANNEL_160MHZ)
+                       data->vht160_supported = true;
+
                if (!lar_supported && !(ch_flags & NVM_CHANNEL_VALID)) {
                        /*
                         * Channels might become valid later if lar is
@@ -331,17 +334,20 @@ static int iwl_init_channel_map(struct device *dev, const struct iwl_cfg *cfg,
                        channel->flags = 0;
 
                IWL_DEBUG_EEPROM(dev,
-                                "Ch. %d [%sGHz] %s%s%s%s%s%s%s(0x%02x %ddBm): Ad-Hoc %ssupported\n",
+                                "Ch. %d [%sGHz] flags 0x%x %s%s%s%s%s%s%s%s%s%s(%ddBm): Ad-Hoc %ssupported\n",
                                 channel->hw_value,
                                 is_5ghz ? "5.2" : "2.4",
+                                ch_flags,
                                 CHECK_AND_PRINT_I(VALID),
                                 CHECK_AND_PRINT_I(IBSS),
                                 CHECK_AND_PRINT_I(ACTIVE),
                                 CHECK_AND_PRINT_I(RADAR),
-                                CHECK_AND_PRINT_I(WIDE),
                                 CHECK_AND_PRINT_I(INDOOR_ONLY),
                                 CHECK_AND_PRINT_I(GO_CONCURRENT),
-                                ch_flags,
+                                CHECK_AND_PRINT_I(WIDE),
+                                CHECK_AND_PRINT_I(40MHZ),
+                                CHECK_AND_PRINT_I(80MHZ),
+                                CHECK_AND_PRINT_I(160MHZ),
                                 channel->max_power,
                                 ((ch_flags & NVM_CHANNEL_IBSS) &&
                                  !(ch_flags & NVM_CHANNEL_RADAR))
@@ -370,6 +376,10 @@ static void iwl_init_vht_hw_capab(const struct iwl_cfg *cfg,
                       max_ampdu_exponent <<
                       IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_SHIFT;
 
+       if (data->vht160_supported)
+               vht_cap->cap |=
+                       IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ;
+
        if (cfg->vht_mu_mimo_supported)
                vht_cap->cap |= IEEE80211_VHT_CAP_MU_BEAMFORMEE_CAPABLE;