STMicroelectronics SoC DWMAC glue layer controller
+This file documents differences between the core properties in
+Documentation/devicetree/bindings/net/stmmac.txt
+and what is needed on STi platforms to program the stmmac glue logic.
+
The device node has following properties.
Required properties:
- compatible : Can be "st,stih415-dwmac", "st,stih416-dwmac",
- "st,stid127-dwmac", "st,stih407-dwmac".
- - reg : Offset of the glue configuration register map in system
+ "st,stih407-dwmac", "st,stid127-dwmac".
+ - reg : Offset of the glue configuration register map in system
configuration regmap pointed by st,syscon property and size.
-
- - reg-names : Should be "sti-ethconf".
-
- - st,syscon : Should be phandle to system configuration node which
+ - st,syscon : Should be phandle to system configuration node which
encompases this glue registers.
+ - st,gmac_en: this is to enable the gmac into a dedicated sysctl control
+ register available on STiH407 SoC.
+ - sti-ethconf: this is the gmac glue logic register to enable the GMAC,
+ select among the different modes and program the clk retiming.
+ - pinctrl-0: pin-control for all the MII mode supported.
- - st,tx-retime-src: On STi Parts for Giga bit speeds, 125Mhz clocks can be
- wired up in from different sources. One via TXCLK pin and other via CLK_125
- pin. This wiring is totally board dependent. However the retiming glue
- logic should be configured accordingly. Possible values for this property
-
- "txclk" - if 125Mhz clock is wired up via txclk line.
- "clk_125" - if 125Mhz clock is wired up via clk_125 line.
-
- This property is only valid for Giga bit setup( GMII, RGMII), and it is
- un-used for non-giga bit (MII and RMII) setups. Also note that internal
- clockgen can not generate stable 125Mhz clock.
-
- - st,ext-phyclk: This boolean property indicates who is generating the clock
- for tx and rx. This property is only valid for RMII case where the clock can
- be generated from the MAC or PHY.
-
- - clock-names: should be "sti-ethclk".
- - clocks: Should point to ethernet clockgen which can generate phyclk.
-
+Optional properties:
+ - resets : phandle pointing to the system reset controller with correct
+ reset line index for ethernet reset.
+ - st,ext-phyclk: valid only for RMII where PHY can generate 50MHz clock or
+ MAC can generate it.
+ - st,tx-retime-src: This specifies which clk is wired up to the mac for
+ retimeing tx lines. This is totally board dependent and can take one of the
+ posssible values from "txclk", "clk_125" or "clkgen".
+ If not passed, the internal clock will be used by default.
+ - sti-ethclk: this is the phy clock.
+ - sti-clkconf: this is an extra sysconfig register, available in new SoCs,
+ to program the clk retiming.
+ - st,gmac_en: to enable the GMAC, this only is present in some SoCs; e.g.
+ STiH407.
Example:
-ethernet0: dwmac@fe810000 {
- device_type = "network";
- compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710";
- reg = <0xfe810000 0x8000>, <0x8bc 0x4>;
- reg-names = "stmmaceth", "sti-ethconf";
- interrupts = <0 133 0>, <0 134 0>, <0 135 0>;
- interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
- phy-mode = "mii";
+ethernet0: dwmac@9630000 {
+ device_type = "network";
+ status = "disabled";
+ compatible = "st,stih407-dwmac", "snps,dwmac", "snps,dwmac-3.710";
+ reg = <0x9630000 0x8000>, <0x80 0x4>;
+ reg-names = "stmmaceth", "sti-ethconf";
- st,syscon = <&syscfg_rear>;
+ st,syscon = <&syscfg_sbc_reg>;
+ st,gmac_en;
+ resets = <&softreset STIH407_ETH1_SOFTRESET>;
+ reset-names = "stmmaceth";
- snps,pbl = <32>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_NONE>,
+ <GIC_SPI 99 IRQ_TYPE_NONE>,
+ <GIC_SPI 100 IRQ_TYPE_NONE>;
+ interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+
+ snps,pbl = <32>;
snps,mixed-burst;
- resets = <&softreset STIH416_ETH0_SOFTRESET>;
- reset-names = "stmmaceth";
- pinctrl-0 = <&pinctrl_mii0>;
- pinctrl-names = "default";
- clocks = <&CLK_S_GMAC0_PHY>;
- clock-names = "stmmaceth";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_rgmii1>;
+
+ clock-names = "stmmaceth", "sti-ethclk";
+ clocks = <&CLK_S_C0_FLEXGEN CLK_EXT2F_A9>,
+ <&CLK_S_C0_FLEXGEN CLK_ETH_PHY>;
};
*
* Copyright (C) 2003-2014 STMicroelectronics (R&D) Limited
* Author: Srinivas Kandagatla <srinivas.kandagatla@st.com>
- *
+ * Contributors: Giuseppe Cavallaro <peppe.cavallaro@st.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
#include <linux/of.h>
#include <linux/of_net.h>
+#define DWMAC_125MHZ 125000000
+#define DWMAC_50MHZ 50000000
+#define DWMAC_25MHZ 25000000
+#define DWMAC_2_5MHZ 2500000
+
+#define IS_PHY_IF_MODE_RGMII(iface) (iface == PHY_INTERFACE_MODE_RGMII || \
+ iface == PHY_INTERFACE_MODE_RGMII_ID || \
+ iface == PHY_INTERFACE_MODE_RGMII_RXID || \
+ iface == PHY_INTERFACE_MODE_RGMII_TXID)
+
+#define IS_PHY_IF_MODE_GBIT(iface) (IS_PHY_IF_MODE_RGMII(iface) || \
+ iface == PHY_INTERFACE_MODE_GMII)
+
+/* STiH4xx register definitions (STiH415/STiH416/STiH407/STiH410 families) */
+
/**
- * STi GMAC glue logic.
- * --------------------
- *
- * _
- * | \
- * --------|0 \ ETH_SEL_INTERNAL_NOTEXT_PHYCLK
- * phyclk | |___________________________________________
- * | | | (phyclk-in)
- * --------|1 / |
- * int-clk |_ / |
- * | _
- * | | \
- * |_______|1 \ ETH_SEL_TX_RETIME_CLK
- * | |___________________________
- * | | (tx-retime-clk)
- * _______|0 /
- * | |_ /
- * _ |
- * | \ |
- * --------|0 \ |
- * clk_125 | |__|
- * | | ETH_SEL_TXCLK_NOT_CLK125
- * --------|1 /
- * txclk |_ /
- *
- *
- * ETH_SEL_INTERNAL_NOTEXT_PHYCLK is valid only for RMII where PHY can
- * generate 50MHz clock or MAC can generate it.
- * This bit is configured by "st,ext-phyclk" property.
- *
- * ETH_SEL_TXCLK_NOT_CLK125 is only valid for gigabit modes, where the 125Mhz
- * clock either comes from clk-125 pin or txclk pin. This configuration is
- * totally driven by the board wiring. This bit is configured by
- * "st,tx-retime-src" property.
- *
- * TXCLK configuration is different for different phy interface modes
- * and changes according to link speed in modes like RGMII.
- *
* Below table summarizes the clock requirement and clock sources for
* supported phy interface modes with link speeds.
* ________________________________________________
* ------------------------------------------------
*| RGMII | 125Mhz | 25Mhz |
*| | clk-125/txclk | clkgen |
+ *| | clkgen | |
* ------------------------------------------------
*| RMII | n/a | 25Mhz |
*| | |clkgen/phyclk-in |
* ------------------------------------------------
*
- * TX lines are always retimed with a clk, which can vary depending
- * on the board configuration. Below is the table of these bits
- * in eth configuration register depending on source of retime clk.
- *
- *---------------------------------------------------------------
- * src | tx_rt_clk | int_not_ext_phyclk | txclk_n_clk125|
- *---------------------------------------------------------------
- * txclk | 0 | n/a | 1 |
- *---------------------------------------------------------------
- * ck_125| 0 | n/a | 0 |
- *---------------------------------------------------------------
- * phyclk| 1 | 0 | n/a |
- *---------------------------------------------------------------
- * clkgen| 1 | 1 | n/a |
- *---------------------------------------------------------------
+ * Register Configuration
+ *-------------------------------
+ * src |BIT(8)| BIT(7)| BIT(6)|
+ *-------------------------------
+ * txclk | 0 | n/a | 1 |
+ *-------------------------------
+ * ck_125| 0 | n/a | 0 |
+ *-------------------------------
+ * phyclk| 1 | 0 | n/a |
+ *-------------------------------
+ * clkgen| 1 | 1 | n/a |
+ *-------------------------------
*/
- /* Register definition */
+#define STIH4XX_RETIME_SRC_MASK GENMASK(8, 6)
+#define STIH4XX_ETH_SEL_TX_RETIME_CLK BIT(8)
+#define STIH4XX_ETH_SEL_INTERNAL_NOTEXT_PHYCLK BIT(7)
+#define STIH4XX_ETH_SEL_TXCLK_NOT_CLK125 BIT(6)
+
+/* STiD127 register definitions */
- /* 3 bits [8:6]
- * [6:6] ETH_SEL_TXCLK_NOT_CLK125
- * [7:7] ETH_SEL_INTERNAL_NOTEXT_PHYCLK
- * [8:8] ETH_SEL_TX_RETIME_CLK
- *
- */
+/**
+ *-----------------------
+ * src |BIT(6)| BIT(7)|
+ *-----------------------
+ * MII | 1 | n/a |
+ *-----------------------
+ * RMII | n/a | 1 |
+ * clkgen| | |
+ *-----------------------
+ * RMII | n/a | 0 |
+ * phyclk| | |
+ *-----------------------
+ * RGMII | 1 | n/a |
+ * clkgen| | |
+ *-----------------------
+ */
-#define TX_RETIME_SRC_MASK GENMASK(8, 6)
-#define ETH_SEL_TX_RETIME_CLK BIT(8)
-#define ETH_SEL_INTERNAL_NOTEXT_PHYCLK BIT(7)
-#define ETH_SEL_TXCLK_NOT_CLK125 BIT(6)
+#define STID127_RETIME_SRC_MASK GENMASK(7, 6)
+#define STID127_ETH_SEL_INTERNAL_NOTEXT_PHYCLK BIT(7)
+#define STID127_ETH_SEL_INTERNAL_NOTEXT_TXCLK BIT(6)
-#define ENMII_MASK GENMASK(5, 5)
-#define ENMII BIT(5)
+#define ENMII_MASK GENMASK(5, 5)
+#define ENMII BIT(5)
+#define EN_MASK GENMASK(1, 1)
+#define EN BIT(1)
/**
* 3 bits [4:2]
* 010-SGMII
* 100-RMII
*/
-#define MII_PHY_SEL_MASK GENMASK(4, 2)
-#define ETH_PHY_SEL_RMII BIT(4)
-#define ETH_PHY_SEL_SGMII BIT(3)
-#define ETH_PHY_SEL_RGMII BIT(2)
-#define ETH_PHY_SEL_GMII 0x0
-#define ETH_PHY_SEL_MII 0x0
-
-#define IS_PHY_IF_MODE_RGMII(iface) (iface == PHY_INTERFACE_MODE_RGMII || \
- iface == PHY_INTERFACE_MODE_RGMII_ID || \
- iface == PHY_INTERFACE_MODE_RGMII_RXID || \
- iface == PHY_INTERFACE_MODE_RGMII_TXID)
-
-#define IS_PHY_IF_MODE_GBIT(iface) (IS_PHY_IF_MODE_RGMII(iface) || \
- iface == PHY_INTERFACE_MODE_GMII)
+#define MII_PHY_SEL_MASK GENMASK(4, 2)
+#define ETH_PHY_SEL_RMII BIT(4)
+#define ETH_PHY_SEL_SGMII BIT(3)
+#define ETH_PHY_SEL_RGMII BIT(2)
+#define ETH_PHY_SEL_GMII 0x0
+#define ETH_PHY_SEL_MII 0x0
struct sti_dwmac {
- int interface;
- bool ext_phyclk;
- bool is_tx_retime_src_clk_125;
- struct clk *clk;
- int reg;
+ int interface; /* MII interface */
+ bool ext_phyclk; /* Clock from external PHY */
+ u32 tx_retime_src; /* TXCLK Retiming*/
+ struct clk *clk; /* PHY clock */
+ int ctrl_reg; /* GMAC glue-logic control register */
+ int clk_sel_reg; /* GMAC ext clk selection register */
struct device *dev;
struct regmap *regmap;
+ u32 speed;
};
static u32 phy_intf_sels[] = {
TX_RETIME_SRC_CLKGEN,
};
-static const char *const tx_retime_srcs[] = {
- [TX_RETIME_SRC_NA] = "",
- [TX_RETIME_SRC_TXCLK] = "txclk",
- [TX_RETIME_SRC_CLK_125] = "clk_125",
- [TX_RETIME_SRC_PHYCLK] = "phyclk",
- [TX_RETIME_SRC_CLKGEN] = "clkgen",
-};
-
-static u32 tx_retime_val[] = {
- [TX_RETIME_SRC_TXCLK] = ETH_SEL_TXCLK_NOT_CLK125,
+static u32 stih4xx_tx_retime_val[] = {
+ [TX_RETIME_SRC_TXCLK] = STIH4XX_ETH_SEL_TXCLK_NOT_CLK125,
[TX_RETIME_SRC_CLK_125] = 0x0,
- [TX_RETIME_SRC_PHYCLK] = ETH_SEL_TX_RETIME_CLK,
- [TX_RETIME_SRC_CLKGEN] = ETH_SEL_TX_RETIME_CLK |
- ETH_SEL_INTERNAL_NOTEXT_PHYCLK,
+ [TX_RETIME_SRC_PHYCLK] = STIH4XX_ETH_SEL_TX_RETIME_CLK,
+ [TX_RETIME_SRC_CLKGEN] = STIH4XX_ETH_SEL_TX_RETIME_CLK
+ | STIH4XX_ETH_SEL_INTERNAL_NOTEXT_PHYCLK,
};
-static void setup_retime_src(struct sti_dwmac *dwmac, u32 spd)
+static void stih4xx_fix_retime_src(void *priv, u32 spd)
{
- u32 src = 0, freq = 0;
-
- if (spd == SPEED_100) {
- if (dwmac->interface == PHY_INTERFACE_MODE_MII ||
- dwmac->interface == PHY_INTERFACE_MODE_GMII) {
- src = TX_RETIME_SRC_TXCLK;
- } else if (dwmac->interface == PHY_INTERFACE_MODE_RMII) {
- if (dwmac->ext_phyclk) {
- src = TX_RETIME_SRC_PHYCLK;
- } else {
- src = TX_RETIME_SRC_CLKGEN;
- freq = 50000000;
- }
-
- } else if (IS_PHY_IF_MODE_RGMII(dwmac->interface)) {
+ struct sti_dwmac *dwmac = priv;
+ u32 src = dwmac->tx_retime_src;
+ u32 reg = dwmac->ctrl_reg;
+ u32 freq = 0;
+
+ if (dwmac->interface == PHY_INTERFACE_MODE_MII) {
+ src = TX_RETIME_SRC_TXCLK;
+ } else if (dwmac->interface == PHY_INTERFACE_MODE_RMII) {
+ if (dwmac->ext_phyclk) {
+ src = TX_RETIME_SRC_PHYCLK;
+ } else {
src = TX_RETIME_SRC_CLKGEN;
- freq = 25000000;
+ freq = DWMAC_50MHZ;
}
+ } else if (IS_PHY_IF_MODE_RGMII(dwmac->interface)) {
+ /* On GiGa clk source can be either ext or from clkgen */
+ if (spd == SPEED_1000) {
+ freq = DWMAC_125MHZ;
+ } else {
+ /* Switch to clkgen for these speeds */
+ src = TX_RETIME_SRC_CLKGEN;
+ if (spd == SPEED_100)
+ freq = DWMAC_25MHZ;
+ else if (spd == SPEED_10)
+ freq = DWMAC_2_5MHZ;
+ }
+ }
- if (src == TX_RETIME_SRC_CLKGEN && dwmac->clk)
- clk_set_rate(dwmac->clk, freq);
+ if (src == TX_RETIME_SRC_CLKGEN && dwmac->clk && freq)
+ clk_set_rate(dwmac->clk, freq);
- } else if (spd == SPEED_1000) {
- if (dwmac->is_tx_retime_src_clk_125)
- src = TX_RETIME_SRC_CLK_125;
- else
- src = TX_RETIME_SRC_TXCLK;
+ regmap_update_bits(dwmac->regmap, reg, STIH4XX_RETIME_SRC_MASK,
+ stih4xx_tx_retime_val[src]);
+}
+
+static void stid127_fix_retime_src(void *priv, u32 spd)
+{
+ struct sti_dwmac *dwmac = priv;
+ u32 reg = dwmac->ctrl_reg;
+ u32 freq = 0;
+ u32 val = 0;
+
+ if (dwmac->interface == PHY_INTERFACE_MODE_MII) {
+ val = STID127_ETH_SEL_INTERNAL_NOTEXT_TXCLK;
+ } else if (dwmac->interface == PHY_INTERFACE_MODE_RMII) {
+ if (!dwmac->ext_phyclk) {
+ val = STID127_ETH_SEL_INTERNAL_NOTEXT_PHYCLK;
+ freq = DWMAC_50MHZ;
+ }
+ } else if (IS_PHY_IF_MODE_RGMII(dwmac->interface)) {
+ val = STID127_ETH_SEL_INTERNAL_NOTEXT_TXCLK;
+ if (spd == SPEED_1000)
+ freq = DWMAC_125MHZ;
+ else if (spd == SPEED_100)
+ freq = DWMAC_25MHZ;
+ else if (spd == SPEED_10)
+ freq = DWMAC_2_5MHZ;
}
- regmap_update_bits(dwmac->regmap, dwmac->reg,
- TX_RETIME_SRC_MASK, tx_retime_val[src]);
+ if (dwmac->clk && freq)
+ clk_set_rate(dwmac->clk, freq);
+
+ regmap_update_bits(dwmac->regmap, reg, STID127_RETIME_SRC_MASK, val);
}
-static void sti_dwmac_exit(struct platform_device *pdev, void *priv)
+static void sti_dwmac_ctrl_init(struct sti_dwmac *dwmac)
{
- struct sti_dwmac *dwmac = priv;
+ struct regmap *regmap = dwmac->regmap;
+ int iface = dwmac->interface;
+ struct device *dev = dwmac->dev;
+ struct device_node *np = dev->of_node;
+ u32 reg = dwmac->ctrl_reg;
+ u32 val;
if (dwmac->clk)
- clk_disable_unprepare(dwmac->clk);
+ clk_prepare_enable(dwmac->clk);
+
+ if (of_property_read_bool(np, "st,gmac_en"))
+ regmap_update_bits(regmap, reg, EN_MASK, EN);
+
+ regmap_update_bits(regmap, reg, MII_PHY_SEL_MASK, phy_intf_sels[iface]);
+
+ val = (iface == PHY_INTERFACE_MODE_REVMII) ? 0 : ENMII;
+ regmap_update_bits(regmap, reg, ENMII_MASK, val);
+}
+
+static int stix4xx_init(struct platform_device *pdev, void *priv)
+{
+ struct sti_dwmac *dwmac = priv;
+ u32 spd = dwmac->speed;
+
+ sti_dwmac_ctrl_init(dwmac);
+
+ stih4xx_fix_retime_src(priv, spd);
+
+ return 0;
}
-static void sti_fix_mac_speed(void *priv, unsigned int spd)
+static int stid127_init(struct platform_device *pdev, void *priv)
{
struct sti_dwmac *dwmac = priv;
+ u32 spd = dwmac->speed;
- setup_retime_src(dwmac, spd);
+ sti_dwmac_ctrl_init(dwmac);
- return;
+ stid127_fix_retime_src(priv, spd);
+
+ return 0;
}
+static void sti_dwmac_exit(struct platform_device *pdev, void *priv)
+{
+ struct sti_dwmac *dwmac = priv;
+
+ if (dwmac->clk)
+ clk_disable_unprepare(dwmac->clk);
+}
static int sti_dwmac_parse_data(struct sti_dwmac *dwmac,
struct platform_device *pdev)
{
res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "sti-ethconf");
if (!res)
return -ENODATA;
+ dwmac->ctrl_reg = res->start;
+
+ /* clk selection from extra syscfg register */
+ dwmac->clk_sel_reg = -ENXIO;
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "sti-clkconf");
+ if (res)
+ dwmac->clk_sel_reg = res->start;
regmap = syscon_regmap_lookup_by_phandle(np, "st,syscon");
if (IS_ERR(regmap))
dwmac->dev = dev;
dwmac->interface = of_get_phy_mode(np);
dwmac->regmap = regmap;
- dwmac->reg = res->start;
dwmac->ext_phyclk = of_property_read_bool(np, "st,ext-phyclk");
- dwmac->is_tx_retime_src_clk_125 = false;
+ dwmac->tx_retime_src = TX_RETIME_SRC_NA;
+ dwmac->speed = SPEED_100;
if (IS_PHY_IF_MODE_GBIT(dwmac->interface)) {
const char *rs;
+ dwmac->tx_retime_src = TX_RETIME_SRC_CLKGEN;
err = of_property_read_string(np, "st,tx-retime-src", &rs);
- if (err < 0) {
- dev_err(dev, "st,tx-retime-src not specified\n");
- return err;
- }
+ if (err < 0)
+ dev_warn(dev, "Use internal clock source\n");
if (!strcasecmp(rs, "clk_125"))
- dwmac->is_tx_retime_src_clk_125 = true;
+ dwmac->tx_retime_src = TX_RETIME_SRC_CLK_125;
+ else if (!strcasecmp(rs, "txclk"))
+ dwmac->tx_retime_src = TX_RETIME_SRC_TXCLK;
+
+ dwmac->speed = SPEED_1000;
}
dwmac->clk = devm_clk_get(dev, "sti-ethclk");
-
- if (IS_ERR(dwmac->clk))
+ if (IS_ERR(dwmac->clk)) {
+ dev_warn(dev, "No phy clock provided...\n");
dwmac->clk = NULL;
-
- return 0;
-}
-
-static int sti_dwmac_init(struct platform_device *pdev, void *priv)
-{
- struct sti_dwmac *dwmac = priv;
- struct regmap *regmap = dwmac->regmap;
- int iface = dwmac->interface;
- u32 reg = dwmac->reg;
- u32 val, spd;
-
- if (dwmac->clk)
- clk_prepare_enable(dwmac->clk);
-
- regmap_update_bits(regmap, reg, MII_PHY_SEL_MASK, phy_intf_sels[iface]);
-
- val = (iface == PHY_INTERFACE_MODE_REVMII) ? 0 : ENMII;
- regmap_update_bits(regmap, reg, ENMII_MASK, val);
-
- if (IS_PHY_IF_MODE_GBIT(iface))
- spd = SPEED_1000;
- else
- spd = SPEED_100;
-
- setup_retime_src(dwmac, spd);
+ }
return 0;
}
return dwmac;
}
-const struct stmmac_of_data sti_gmac_data = {
- .fix_mac_speed = sti_fix_mac_speed,
+const struct stmmac_of_data stih4xx_dwmac_data = {
+ .fix_mac_speed = stih4xx_fix_retime_src,
+ .setup = sti_dwmac_setup,
+ .init = stix4xx_init,
+ .exit = sti_dwmac_exit,
+};
+
+const struct stmmac_of_data stid127_dwmac_data = {
+ .fix_mac_speed = stid127_fix_retime_src,
.setup = sti_dwmac_setup,
- .init = sti_dwmac_init,
+ .init = stid127_init,
.exit = sti_dwmac_exit,
};
projects / cascardo / linux.git / commitdiff