serial: 8250_dw: Use 64-bit access for OCTEON.

Although the existing code appears to work on most hardware, the
hardware designers tell us that 8-bit access to the registers is not
guaranteed to be reliable.  Also the OCTEON simulation environments
prohibit 8-bit accesses.

For these reasons, we use __raw_readq/__raw_writeq for OCTEON.  This
code is protected with #ifdef CONFIG_64BIT so it still builds under
configurations lacking readq/writeq.

We can get rid of the #ifdef __BIG_ENDIAN, as under 64-bit accesses,
OCTEON is byte order invariant.

Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@auriga.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index 18ff532..f4fd362 100644 (file)
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -122,13 +122,44 @@ static unsigned int dw8250_serial_in(struct uart_port *p, int offset)
        return dw8250_modify_msr(p, offset, value);
 }
 
-/* Read Back (rb) version to ensure register access ording. */
-static void dw8250_serial_out_rb(struct uart_port *p, int offset, int value)
+#ifdef CONFIG_64BIT
+static unsigned int dw8250_serial_inq(struct uart_port *p, int offset)
 {
-       dw8250_serial_out(p, offset, value);
-       dw8250_serial_in(p, UART_LCR);
+       unsigned int value;
+
+       value = (u8)__raw_readq(p->membase + (offset << p->regshift));
+
+       return dw8250_modify_msr(p, offset, value);
 }
 
+static void dw8250_serial_outq(struct uart_port *p, int offset, int value)
+{
+       struct dw8250_data *d = p->private_data;
+
+       if (offset == UART_MCR)
+               d->last_mcr = value;
+
+       value &= 0xff;
+       __raw_writeq(value, p->membase + (offset << p->regshift));
+       /* Read back to ensure register write ordering. */
+       __raw_readq(p->membase + (UART_LCR << p->regshift));
+
+       /* Make sure LCR write wasn't ignored */
+       if (offset == UART_LCR) {
+               int tries = 1000;
+               while (tries--) {
+                       unsigned int lcr = p->serial_in(p, UART_LCR);
+                       if ((value & ~UART_LCR_SPAR) == (lcr & ~UART_LCR_SPAR))
+                               return;
+                       dw8250_force_idle(p);
+                       __raw_writeq(value & 0xff,
+                                    p->membase + (UART_LCR << p->regshift));
+               }
+               dev_err(p->dev, "Couldn't set LCR to %d\n", value);
+       }
+}
+#endif /* CONFIG_64BIT */
+
 static void dw8250_serial_out32(struct uart_port *p, int offset, int value)
 {
        struct dw8250_data *d = p->private_data;
@@ -260,21 +291,17 @@ static int dw8250_probe_of(struct uart_port *p,
        bool has_ucv = true;
        int id;
 
+#ifdef CONFIG_64BIT
        if (of_device_is_compatible(np, "cavium,octeon-3860-uart")) {
-#ifdef __BIG_ENDIAN
-               /*
-                * Low order bits of these 64-bit registers, when
-                * accessed as a byte, are 7 bytes further down in the
-                * address space in big endian mode.
-                */
-               p->membase += 7;
-#endif
-               p->serial_out = dw8250_serial_out_rb;
+               p->serial_in = dw8250_serial_inq;
+               p->serial_out = dw8250_serial_outq;
                p->flags = UPF_SKIP_TEST | UPF_SHARE_IRQ | UPF_FIXED_TYPE;
                p->type = PORT_OCTEON;
                data->usr_reg = 0x27;
                has_ucv = false;
-       } else if (!of_property_read_u32(np, "reg-io-width", &val)) {
+       } else
+#endif
+       if (!of_property_read_u32(np, "reg-io-width", &val)) {
                switch (val) {
                case 1:
                        break;